Houzz is the new way to design your home.
4,628 corten steel planter Home Design Photos
fence Corten steel or mild steel?
oxidized corten is very similar to mild steel. The main difference (besides cost) is that corten will only patina to a certain level then stop, while mild steel will continue to oxidize till it rusts out- not a problem if the water running off the wall goes into a flower bed filled with plants that like
this is corten because there isn't any visible staining on the patio which the water running off of mild steel would cause.
like the planter on the inside
Northern Virginia Landscape Architect and Custom Pool Builder
Pristine Acres is committed to offering the highest-quality, most professional landscape design/installation services with the best customer service in the Washington DC Metro.
Banyon Tree Design Studio
cold-rolled steel for railing spindles. Thanks!
How far below grade did you bury each of the steel stair treads?
how (sizes) and where can the steel be purchased?
local steel fabricator in your area to construct the piece you are looking for. good luck!
use of steel, gravel and approach!
love Cor-Ten, but also love the steel steps with pea gravel fill!
corten steel and dk grey gravel
raised planter at the base of the embankment
Corten steel not this size but material
wow, beautiful steel wall with fountain
curved steel wall, a spiral in both plan and elevation, divides the upper and lower areas of the front yard. It is made from cold-rolled ¼-inch plate steel. Port used a concrete block wall beneath the ornamental steel wall to structurally secure the 5-foot grade change. A curved wood bench projects off
corten, gabian wall planters, simple planter, metal & wood
Metal troughs with rock in cage legs for planters. Cool.
Steel planters supported by rocks in wire cages
how clever with stone and steel raised beds
post for raised planter
Planter idea by dock
Planters with stones
planters I can make these
from the steel of the rill to the gravel below.
planter idea...Planter bench...steel color...Neat planters...Planter box...steel and rOcks
Huettl Landscape Architecture
how the Corten Fence is installed? How is it seated into the ground? concrete footings? Thanks!
in the steel sheets and rebar are inserted which help it connect to the reinforced concrete footing that is poured around it.
also wondering how the steel is installed thx
Wind Break Cordan Steel with Grasses
steel as screening, planters and intrique
corten steele. plants planted below level of paving like the batters we currently have?
firepit, cor-ten steel, clean looking cement slab
Cor-ten dividers or even fence panels?
Steel plates anchored in concrete as focus point
Combination of Corten Steel and Grass
cor ten steel & grasses, simple
"The Cor-Ten seems to rust more evenly than regular mild steel and therefore is often worth the extra cost for those instances where you want a calm, consistent rusty color as a backdrop or foil for plantings," says landscape architect Joseph Huettl.Feathery grasses create a dynamic backdrop beyond these
Tim Davies Landscaping
is the steel plate vs say stone?
How thick is the steel?
Drip irrigation w raised planter for. Herbs
5-6mm steel with internal cross bracing beneath synthetic turf
raised planter. core10
For planters around pool
Natural steel, rusted
steel retaining wall
more carbon [Cor-Ten] steel walls
steel walls/turf drip irrigation
Corten Steel retinaing wall!
Here Cor-Ten steel has been used to form a cost-effective barrier.
cool steel planters...corton steel...use of corten steel...Stone and Steel...Steel wall...Steel edging
over the corten rusted-steel edges of this courtyard waterfeature and down into a small channel also filled with pebbles. This whole structure was set to finish flush with only a half-inch gap between the water surface and a cast concrete seat wall that extends along the courtyard’s perimeter. The pool’s
will the corten steel last as a water feature?
I have been advised this type of steel may not be too great over a long period of time as the water washes the rust effect away? It looks fantastic though and would like to use it if possible.
Corten edging walls on infinity water feature
Water runs over the Cor-Ten-steel-edged, rock-filled pool custom created by Bianchi Design.
“will the corten steel last as a water feature?” “I have been advised this type of steel may not be too great over a long period of time as the water washes the rust effect away? It looks fantastic though and would like to use it if possible.” “Water runs over the Cor-Ten-steel-edged, rock-filled” “The steel
the construction zone, ltd.
The Brown Residence
rolled steel, over a waterproof membrane
glass + steel retreat in the Mojave
hot rod steel instead of cor 10
Can we use corten steel for window frames
Love the steel incorporatedino walls and the jilt in firepit
Exterior material - sheet steel panels
Hot-Rolled Steel The process of hot rolling steel begins with larger raw materials
rolled steel over water proof membrane
cold rolled steel - could do door like this
use of cold rolled steel for exterior
the steel cannot be beat for its multitude of appearance and effect...
hot-rolled steel all around the project; in our dry climate, we don't need to use weathering Cor-Ten steel," says Byrnes.
Hot-Rolled SteelThe process of hot rolling steel begins with larger raw materials and can be done more quickly (no need to wait for cooling) and efficiently. This process yields a
How much is corten steel approx per linear foot?
guage steel (I plan to dothe same). How did you join the strips together? It appears that there is some sort of clip, or are these simply strips of the same steel cut in 3or 4" wide strips 18" long so that they can be anchored in the ground to support the curves?
I used cold-rolled steel to frame
layers. Cor-ten is much more expensive, but after the work it takes to get steel to look like this and be protected, its worth it. (unless you're looking for a 3 year solution). I've never seen metal like this at a building store, look for a local "metal supply" or "metal fabricator." For metal patinaing
work that cor-ten would have been much more worth it. I then painted the back side with rust-preventing paint, patinaed the front so it would rust immediately, then applied a 2-part clear coat to protect it. Without the protection, the metal would fail in 3-5 years (and it was heavier gauge than this)