Houzz is the new way to design your home.
172 Twyford 3D vanity unit & side unit Entry Design Photos
Did you mean: stafford 3rd vanity unit side unit
Creative Touch Interiors
this unit, can you tell me the depth?
What are the measurements of this unit?
Love the whole unit, where can I buy it??
Would love to know where to buy the storage unit, we're looking to remodel our laundry room and that would be perfect.
custom unit cost. So I have an idea.
4'-4"W x 2' D; the left and right side is 1'-8.5"W x 2'-1"D. The seat height is 18" and approx. 66" to the bottom of the storage shelf.
bench unit came from? I'm also curious about the cushion, where was it purchased?
This unit was built-in by the builder and custom designed by CTI.
Will this fit on right side of entry!
Small coat storage to one side, cubby and bench on the other
Mohler + Ghillino Architects
for main unit below the cantilevered upper floor. photo: Fred Kihara
What is the siding? Looks great!
The siding is a box-rib corrugated sheet metal siding manufactered by AEP Span. It is in a Zatique II finish. It requires no maintanance so it helps balance the maintanace required on the clear finish decks, doors and windows.
locally. i'd have to go back through the files to confirm.
Modern stepped entry w metal siding
box rib corrugated metal siding - combine with clear western red cedar; love the stark contrast of cool metal and warm wood
bottom unit – 18” high, middle unit: 48”, top unit: 11” high. The wood is ¾” plywood. Hope that helps! Linda
Restyled Home My husband built the lockers and reports the following measurements (for an individual locker): depth - 15”, over all height – 79”, width – 19”, bottom unit – 18” high, middle unit: 48”, top unit: 11” high. The wood is ¾” plywood. Hope that helps!
sides of our unit would look similar to this
3 hooks varying height. Needs to be a wire rack on bottom for wet shoes.
ished 3/4" plank. The installer (Krystynick Flooring for those in Austin) supplied it, we had seen it in a few other houses, so we told them to match what they had done before.
We did have the doors custom made. However, it is not a custom unit. It is actually
single units like this, but they were impressively expensive, this was just mildly expensive. However, we really feel it was worth it for the functionality. We open the side doors quite a bite during the Spring and Fall.
of the side doors is to be able to open them to allow breezes to move through the house (there are screens to prevent the cat and pesky insects from doing similarly) without having to have a screen door on the main door of the house.
Diane Burgoyne Interiors
seating unit or custom made. What dimensions, this is what I need. .
on the sides...The storage unit...Wall Unit...Bench unit...Side entrance
A Lake Home
Like bench in muddle and drawers on either side
would be awesome with closed lockers going all the way up on both sides
Left side ladder, right side shelves
on this unit? Thank you!
Sitting unit...The unit...lockers 3...Coat unit.....on one side
Quaker Bluff Residence
cut 2 x 3 and 2 x 2 to finish with a pre drilled dowel holes to stack glue and clamp. Or if you have access to a large scale D&C routing table to pre cut assembled 5/4 slabs for either side of a foam core panel while pre morticing the unit for future assemble. Good work is copied and emulated by those
sold 50 units. Most will not make this level, but there is a satisfaction of seeing that the design is appreciated.
other side. Here is a view from outside in the evening ...
the back side to maintain a wonderful glossy finish. This particular application is referred to as a factory finish. Heavy-duty epoxy paint is uniformly applied to the reverse side of the glass in a controlled environment to prevent imperfections. The end result is a perfect finish, seen through the other
Crystal Kitchen Center
ASID Showcase House
on all 3 sides, to get the same floating effect.
room? I'd like to do the same ceiling in my kitchen but was wondering if 8 ft is too low?
supported by 3/4" stock material that runs the length and on the sides underneath the top.
Hood morning, Thank you for your inquiry on this project. The openings are approximately 16"w x 12" d x 12"h(the bottom cubby is 16"W x 12" d x 14"h). If you are designing this from scratch, we would suggest
The bench was existing, but we believe it is maple. It is supported by 3/4" stock material that runs the length and on the sides
Hooks and baskets on the side for mud room