134 no drill Modern Home Design Photos

Ceramiques Hugo Sanchez Inc
4 Reviews
Modern style bathroom with linear drain
Ideabooks1,198
Questions0
from an article I bookmarked and the article is about tile positioning and drilling.
BATH The oversize tile is installed flawlessly. The tile for the shower controls was drilled for the plumbing fixture and mitered along the long edge (the bottom of
The tile for the shower controls was drilled for the plumbing fixture and mitered along the long edge (the bottom of the tile) to meet the tile on the top of the niche.
This is one of my favorite bathrooms ever. The oversize tile is installed flawlessly. The tile for the shower controls was drilled for the plumbing fixture and mitered along the long edge (the bottom of the tile) to meet the tile on the top of the niche. So much effort for just
This is one of my favorite bathrooms ever. The oversize tile is installed flawlessly. The tile for the shower controls was drilled for the plumbing fixture and mitered along the long edge (the bottom of the tile) to meet the tile on the top of the niche. So much effort for just
“niche” — mr_joshua
Dichotomy Interiors
7 Reviews
butterfly roof residence
Ideabooks1,204
Questions2
Mayone drilled holes through the walnut and into the 2-by-4s, then fit the rods into the holes. Oldenburger recommends using tape while drilling to minimize splintering. "Measure your cuts on the aluminum rods by the length of
metal rods drilled into post support the wine bottles.
Mayone drilled holes through the walnut and into the 2-by-4s, then fit the rods into the holes. Oldenburger recommends using tape while drilling to minimize splintering. "Measure your cuts on the aluminum rods by the length of the bottle and then add the additional inches for the wood which will hold
“Bar pulls” — Celeste Designs
John Whipple - By Any Design ltd.
40 Reviews
Westridge Master Ensuite - West Vancouver
Ideabooks4,883
Questions3
shower drilled a perfect hole for the shower hose. These holes are drilled very close to the edge of the tile, which is hard to get right. Tip: When drilling holes so close to the edge of the tile, make sure that the tile is protected from vibration damage. Fully support the tile while drilling and press
“Need these” — juliethomson
Northern VA Landscape Architect & Designer
Best of Houzz 2013 & 2014
Since 1999, we have worked with homeowners to develop truly unique and distinctive outdoor living spaces. We specialize in upscale poolscapes, hardscapes and landscapes.
Sponsored
Sasha Lanka
Modern Loft Project
Ideabooks1,670
Questions4
DIY bench, buy bench drill holes strap thorough 2 matching belts
strappy leather accents on upholstery. I love how the belt-style strap holds the cushion in place in this room. This could be a simple DIY project: Just drill four holes, run matching belts through and secure them in place.
“end table/bench with straps” — dennipep
Envi Interior Design Studio
The Bon Ton Loft
Ideabooks4,047
Questions3
In wood-framed structures, holes are drilled through wood studs and the electrical wire is pulled through. Nail plates are added on the outside of the stud before any wallboard is put up, to prevent anyone from hammering nails into the electrical cable.
“blue paint” — lknop
dSPACE Studio Ltd
5 Reviews
Powder Room
Ideabooks4,650
Questions12
Can you please share the method you used to float your mirror? Did you glue your mirror to a piece of plywood and then drill the plywood into the wall studs? I want to do the same with my master bath, however my walls are already tiled so i'm a bit stuck on how to attack
and LED lighting was installed by the electrician in the space behind the mirror, top and bottom. Your general contractor/installer may be able to drill through the existing tiles to attach the plywood and blocking to the studs in the walls. However, if they are concerned about cracking, they may recommend
and LED lighting was installed by the electrician in the space behind the mirror, top and bottom. Your general contractor/installer may be able to drill through the existing tiles to attach the plywood and blocking to the studs in the walls. This bathroom is actually painted drywall. Benjamin Moore has
“Lighting behind mirror. Int. sink/surface” — rustywd
Charles Luck Stone Center
1 Review
Exterior
Ideabooks309
Questions1
This would be easier than drilling holes, but it may be a "hip-hazard".
“Dock rail” — randlneufeld
Cary Bernstein Architect
1 Review
Cary Bernstein Architect Ridge House
Ideabooks2,969
Questions2
drilled holes for airline cable arbour
“Cable Wiring Cover” — marmij06
© 2014 Houzz Inc.
Houzz® The new way to design your home™