595 screw Traditional Home Design Photos

Sarah Greenman
1 Review
Dallas, TX: Tyler & Crispin Deneault
Ideabooks248
Questions0
which are screwed into the wall.
Add vintage knob to a support/wall screw
drawer pulls attached to long screws. shutters rest on them and lean against wall.
Long screws w/knobs to hold up shutters.
Shutters resting on knobs and screws.
to long screws so that the shutters could rest on them and lean back against the wall.
The shutters are solid wood and therefore quite heavy. Due to their age and patina, the Deneaults didn’t want to attach any hardware to them. Tyler rigged these vintage drawer pulls to long screws so that the shutters
to long screws so that the shutters could rest on them and lean back against the wall.
“If we want to hangs our shutters on the wall.” — jrmeunier
Karen Heffernan
Our New Kitchen
Ideabooks2,834
Questions2
dowel pin screwed into the bottom
By installing a pegboard cut to the size of your drawer and using wooden dowels with a dowel pin screwed into the bottom, you can
dowel pin screwed into the bottom, you can create your own customizable dish organizer.
make it myself; get pegboard cut size of draw, wooden dowels with a dowl pin screwed into bottom
dowel pin screwed into the bottom, you can create your own customizable dish organizer. The dowels keep the dishes in place and can be moved around as needed.
By installing a pegboard cut to the size of your drawer and using wooden dowels with a dowel pin screwed into the bottom, you can create your
dowel pin screwed into the bottom, you can create your own customizable dish organizer. The dowels keep the dishes in place and can be moved around as needed."
“drawer storage” — Bouche' Design Group
Schtork, LLC
Kid's Bathroom Remodel
Ideabooks73
Questions0
Remove the screws holding in the old light switch and gently pull it out of the wall. The switch either will be held by wires wrapped around connector screws at its sides, or will have wires coming out of it that are connected to wires coming out of the wall and capped with wire nuts (they look like marker
connector screws, undo them, snip them and strip them. Follow the package instructions to loop the ends of the wire around the connector screws on the new dimmer switch and tighten them with a screwdriver. If the unit is installed wire to wire, remove the wire nut and untwist the copper strands, then snip
Remove the screws holding in the old light switch and gently pull it out of the wall. The switch either will be held by wires wrapped around connector screws at its sides, or will have wires coming out of it that are connected to wires coming out of the wall and capped with wire nuts (they look like marker
“I like these dimmer switches.” — croisanmountain
Northern Virginia Landscape Architecture and Construction
Metes & Bounds Landscape Design was established in 2004 as a landscape architecture firm dedicated to providing full-service design/build solutions for residential properties.
Sponsored
Erin Lau Landscape Design- Seattle
19 Reviews
Wallingford Vegetable Beds
Ideabooks872
Questions1
Predrill and screw in the timberLOK screws to fasten the two courses together (see diagram). Continue in the same way with the other three corners. 4. Check that the rectangle is square. Continue to build up the courses, checking that they are level and square as you go. All the courses are fastened in the
timberLOK screws at each corner screwed down into the course below it. Build the beds as tall as you like, but it’s important to keep in mind that cost and time will increase as the height does. If you’re building on a parking strip or easement, like these juniper beds were built, local codes may dictate
with deck screws. This box has a 2-inch overhang, and the cap is mounted flush with the inside of the box. How much the cap hangs over is up to you, but make sure it’s consistent around the box. 6. For the bench, bolt at least three supports into the 4-by-4s of the raised bed (see diagram). The bench portion
“sitting ledge on box, grid wires for planting, wood chips (better than pea gravel IMO)” — lisamarietoe
Venegas and Company
10 Reviews
Le Metro
Ideabooks1,628
Questions8
center (screw hole to screw hole) dimension and go find some new, interesting hardware. A screw driver and an hour are all you need.
center (screw hole to screw hole) dimension and go find some new, interesting hardware. A screw driver and an hour are all you need.
“Cabinet knobs” — lsmith221
Boor Bridges Architecture
farmhouse kitchen
Ideabooks5,156
Questions12
it; a screw-into-the-wall version is much more secure. Childproofing consultant Altman reminds us, though, that “childproofing is an ongoing process. The gate you put at the top of the stairs for your 1-year-old may become his favorite climbing structure when he’s 2.”
“Hardwood floor finish” — slm1988
LORRAINE G VALE, Allied ASID
19 Reviews
Lorraine Vale
Ideabooks3,548
Questions7
stapled or screwed in place.Tip: Decide early on which lines you want highlighted in your cane chair. Do you want a curved back for a fun and flirty room; a rounded top, which is versatile enough for any decor; or a straight back for a more formal setting?
“Love the dining chairs” — onetennismom
Dawn Hearn Interior Design
25 Reviews
Traditional Front Porch Christmas
Ideabooks41,928
Questions13
You'll need screws made for masonry and know where to drill and how to repair the holes after the holidays.
“awesome brick” — tlincolnde
© 2014 Houzz Inc.
Houzz® The new way to design your home™