Software
Houzz Logo Print
afjenkins

Updating stained concrete floors?

7 days ago

Hi! My house is almost 25 years old. When built we took care and had the whole 1st floor concrete slab professionally polished/cut and stained. It’s a chocolate brown. I am in Central Texas. It has been a great floor raising 4 kids and multiple large dogs.
Now, it’s time to get ready to sell in the next few years. It’s not a super expensive house (~500k). What should I do?
Tile? LVP?
See if it could be professionally polished again and let new buyers decide?

Thanks for opinions.

Comments (11)

  • 7 days ago
    last modified: 7 days ago

    A desirable floor to look at is wide plank, flat cut pale non yellow matte finished engineered European Oak. Hurst Hardwoods can have good pricing. Did your floor get a 5mm vapor barrier under the pour? Link.



  • 7 days ago

    I like that floor and see that look a lot. No, I don’t think there is a vapor barrier but have not had moisture be an issue. We don’t get a lot of rain.

  • 7 days ago

    To test tape around a foot or so of plastic wrap in a few areas for 48 hours. If no moisture that's great.

  • PRO
    7 days ago

    Have a professional come in to clean and re-burnish the floors. You do not need to do a full polish.

  • 6 days ago

    " See if it could be professionally polished again and let new buyers decide? "


    Between what G&S says above and this question by you is your answer.

  • 6 days ago

    Good! I don’t want the floors to be an immediate turn off when a potential buyer walks in. But I can face that if it happens.

  • 6 days ago

    Flooring is a major design component for an interior. Bringing your house completely up to current level will have a positive impact on buyers. It will sell faster for more money.

  • PRO
    5 days ago

    Selling in a few years at that price point, I wouldn't cover a polished slab. Texas buyers get concrete, and it's basically indestructible. The chocolate stain is what dates it, not the floor. Have a concrete polishing pro look at it. Often they can grind, go lighter or more natural, and repolish for way less than tile or LVP through the whole first floor. If they say it can't be lightened, I'd still do a fresh polish and let buyers decide. LVP over a good slab right before listing can actually read as a downgrade.

  • 5 days ago

    AI would find 5-15 homes per 10,000 listings $500k-700k in El Paso and Lubbock areas. That is very niche. I'd change it. But, imo, only to engineered Euro Oak.

  • PRO
    4 days ago

    @dan1888 Fair point on the buyer pool. If they do replace it, I'm with you, engineered European oak over LVP every time, and get a moisture test on the slab first. My take is still cost vs return. Covering or removing a stained slab is real money before resale, while a regrind and a lighter neutral stain kills the dated chocolate tone for a fraction. Staying ten plus years, go oak. Selling soon, refinish the concrete.

  • 4 days ago
    last modified: 4 days ago

    These forums help with the info to check pricing for two specific choices. The op can focus on learning more about 2 things now. I think that's a good start. Eoropean Oak is totally different in grain than domestic white or red oak. Closed grain allows flat cut to show off the grain cathedrals using 7 to 11 inch wide boards. Go for hardwood eucalyptus or birch plywood core, especially using a 3mm top layer to reduce denting.

    Another thing t check in addition to moisture content is floor flatness. LVP is thin with various quality levels of holding power for the different locking mechanisms. You need a flatter floor over a 10 foot area than is needed for much thicker laminate or engineered planks. 1/8" over 6 feet. 3/16" over a 10 foot span for LVP, laminate and engineered. These requirements are the same but LVP flexes and this is more likely to lead to failure of the locking mechanism, imo. Flatter is always better for everything.