Knobco and Prime-Line Products Cabinet and Drawer Hardware

This by-pass closet door track is constructed of galvanized steel. It features the same double J-track as those used in Prime-Line's 2-door kits, and it can also be used with 3-door by-pass systems. The track length is pre-cut to 95 in. to minimize the need for cutting, and it is commonly used with wooden door panels measuring from 3/4 in. thick to 1-3/8 in. thick. This track will safely hold doors that weigh up to 60 lbs. each, and it can be used to mount one panel on each track or one panel on one track and two panels on the second.

• Used to hang two and three door, by-passing sliding closet door panels
• Accepts 3/4 in., 7/8 in., 1-1/8 in. or 1-3/8 in. thick doors
• Galvanized steel construction
• Constructed of one solid piece of track
• Installation fasteners are included with this item
• For further dimensional information, please see the line drawing

This back plate is constructed from plastic and is used to hold your track to the back of your cabinet. It features a reversible design for right or left-handed tracks. Fits on most popular side mount rails.

• Reversible for right or left hand track
• Mounts in back of cabinet, supports track
• White in color
• Easy to install with a few simple tools
• Installation fasteners are included
• For further dimensional information, please see the line drawing

These drawer slide kits are constructed of steel tracks with plastic rollers and come in a white powder-coated finish. They feature a self-closing design that commences at the final 2-1/2 in. from the end of the 19-3/4 in. long tracks when closing. The maximum load capacity for this kit is 75 lbs., and it fits most bottom-mount drawer systems. This kit cannot be cut down to fit smaller drawer depths as it is designed with a positive stop at the ends of the fixed tracks, and because the rear rollers (11/16 in. diameter wheels) on the sliding tracks are fastened to the ends of the drawer-mounted track pieces. These bottom-mount drawer slides can be installed in drawer cabinets with face frames and without. If installing in drawer cabinet with face frame, Prime-Line part R 7240 (purchased separately) may be necessary if existing back plates are damaged. The clearance required between the drawer and the drawer opening for these types of slides is as follows: 1/2 in. on left and right sides, 1/4 in. at the bottom and 5/8 in. at the top. Installation instructions are included with each set, and they can also be found within the manufacturer�s website.

• These drawer slides can be installed in cabinetry constructed with and without face frames, that have a depth of 20 in.
• Durable steel-constructed drawer slides with plastic wheels designed for years of use
• Designed with self-closing feature that begins towards the end of the slide
• Easy to install slides fit most bottom-mount drawer systems
• Maximum load capacity is 75 lbs.
• Ideal for use in kitchen cabinets
• Installation fasteners and instructions are included
• For further dimensional information, please see the line drawing

This 13/16 in diameter roller features a 3-3/8 in. high bracket. Roller is a 5/16 in. in width. It mounts on the left side of your drawer when viewed from the rear. Contains 2 rollers and includes fasteners for a quick and easy installation.

• Used by mono-rail track drawers
• Right hand roller
• Mounting holes are 1-5/8 in. on center
• Stamped steel construction with nylon roller
• Features a 13/16 in. roller
• Mounting hardware included
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

This is a white plastic track guide and glides with no back alignment tabs. The white plastic side saddles restores smooth operation of track mounted drawers.

• Constructed from white polyethylene
• Guide with no back alignment tabs
• Side saddles
• Restore smooth operation
• For further dimensional information, please see the line drawing

These roller assemblies are constructed of steel brackets and plastic wheels, and they're manufactured in a left and right-hand roller assembly. The roller assemblies are used to replace worn or missing guide buttons, allowing the drawers to glide easily when opening and closing, while at the same time preventing wear on the cabinet�s face frame or drawer opening. These roller assemblies install into the inside lower left and right corners of the drawer face opening with necessary fasteners provided within each kit. This pair of roller assemblies have a max load rating of 20 lbs., and they are used by many to replace missing or malfunctioning drawer track hardware. For a complete kit with track, guide and back plate, see Prime-Line part R 7137.

• Used on the front of drawer opening to aid in a smoother operation
• Features a 1 in. outside diameter roller, 9/16 in. wide
• Used to help center your drawer
• Constructed of steel brackets and plastic wheels
• Includes 1 left hand and 1 right hand roller assembly
• Mounting hardware included
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

This is an adjustable stamped steel sliding closet door floor guide, with nylon tips. The guides are made of white nylon and can be adjusted to accommodate doors from 3/4 in. to 1-3/8 in. wide. Used by a variety of closet door manufacturers.

• Used by Acme and a variety of other closet door manufacturers
• Fits doors from 3/4 in. to 1-3/8 in. thick
• 2 guides per package
• Stamped steel base with adjustable white nylon tips
• Guides are 5/8 in. tall
• Fasteners are included
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

These rear drawer track brackets are constructed of a thick, durable plastic and they come in white, left and right-hand pair. They are designed to support and maintain alignment of bottom/side-mounted steel drawer slides They feature an easy to install design, with a 3-9/16 in. socket depth to allow for front to back adjustment of the drawer slides. This pair of drawer track back plates includes the installation fasteners, and they have a maximum load rating of 75 lbs. per pair. These rear drawer replacement track sockets are simple to install and are used by many.

• Used to support side mounted drawer glides
• 3/8 in. wide x 1 in. tall x 3-9/16 in. deep openings
• Fits drawer track systems that are 3/8 in. x 1 in.
• White plastic construction
• Contains 1 pair of drawer track back plates (1 left and 1 right)
• Mounting hardware included
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

This is a drawer guide and glide set constructed from mold injected brown plastic. Typically this set can be used with a majority of furniture drawer systems. The saddles offer less resistance on the drawer being pulled out or pushed in making this set perfect for your dressers, hutches and night stand drawers. Opening for metal track on the large piece is 15/16 in. x 3/32 in. make sure to measure your track before ordering. All the necessary mounting hardware is included for a quick and easy installation.

• Typically used for dressers, hutches and night stand drawers
• Replaces Rite-Trak Drawer Hardware
• A metal track is required for these guides but is not included
• Dark brown plastic construction
• Contains 2 dark brown plastic track case guides 2 track guides and 4 white glides
• For dressers, hutches and night stand drawers
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

This is a plated diecast housing and steel cam lock with 3 different cams, and features a classic bronze face. It can be mounted to metal or wood doors or drawers with a maximum 13/16 in. thickness. 2 Yale Y-11keys come with this cam lock. Dimensions are 1-1/8 in. length and a 3/4 in. diameter cylinder. An adjustable wrench will be required for installation.

• Used on doors and drawers that are 13/16 in. thick
• Allows you to secure drawer or cabinet
• Can be special ordered to be keyed the same
• Durable diecast and steel construction with a bronze finish
• All hardware included for installation
• Contains 1 lock, 3 cams, 1 trim collar, 1 spur washer, 2 rotation washers, 1 lock nut and 2 keys
• Body of this lock is 1-1/8 in. diameter with a face of 7/8 in. diameter
• For further dimensional information, please see the line drawing

These drawer slide kits are constructed of steel tracks with plastic rollers and come in a white powder-coated finish. They feature a self-closing design that commences at the final 2-1/2 in. from the end of the 17-3/4 in. long tracks when closing. The maximum load capacity for this kit is 75 lbs., and it fits most bottom-mount drawer systems. This kit cannot be cut down to fit smaller drawer depths as it is designed with a positive stop at the ends of the fixed tracks, and because the rear rollers (11/16 in. diameter wheels) on the sliding tracks are fastened to the ends of the drawer-mounted track pieces. These bottom-mount drawer slides can be installed in drawer cabinets with face frames and without. If installing in drawer cabinet with face frame, Prime-Line part R 7240 (purchased separately) may be necessary if existing back plates are damaged. The clearance required between the drawer and the drawer opening for these types of slides is as follows: 1/2 in. on left and right sides, 1/4 in. at the bottom and 5/8 in. at the top. Installation instructions are included with each set, and they can also be found within the manufacturer�s website.

• These drawer slides can be installed in cabinetry constructed with and without face frames, that have a depth of 18 in.
• Durable steel-constructed drawer slides with plastic wheels designed for years of use
• Designed with self-closing feature that begins towards the end of the slide
• Easy to install slides fit most bottom-mount drawer systems
• Maximum load capacity is 75 lbs.
• Ideal for use in kitchen cabinets
• Installation fasteners and instructions are included
• For further dimensional information, please see the line drawing

These guides are constructed from brown plastic. They help in keeping your drawers aligned and make for a smoother operation. Fits a 1/4 in. by 7/8 in. track.

• Bulk pack includes guides only, the fasteners and corner saddles not included
• Fits a 1/4 in. x 7/8 in. track
• Plastic construction
• Brown colored guide
• For further dimensional information, please see the line drawing

This drawer track guide and glides are constructed from plastic. It features a rear mounted design that keeps this item out of sight. It is used for aligning drawers and helps for a smooth operation.

• Includes guides and side saddles
• Fits a 1/4 in. x 3/4 in. track
• Plastic construction
• Blue colored guide
• White colored saddles
• For further dimensional information, please see the line drawing

These cabinet knob backplates are constructed of stamped steel and come in a satin nickel plated finish. Backplates like these are used on both cabinet doors and drawer faces to prevent the wearing of finished wood, and the unsightly accumulation of dirt and grime. They feature a large 2-13/16 in. outside diameter and they project outward a total of 3/16 inches. These cabinet knob backplates do not include any installation fasteners, but they come with pre-punched holes for quick and easy installation.

• Used beneath cabinet knobs to prevent scratches to finished wood, and to prevent the unsightly accumulation of dirt and grime
• 2-13/16 in. outside diameter x 3/16 in. projection
• Satin nickel finish
• Stamped steel construction
• Easy to install with a few simple tools
• For further dimensional information, please see the line drawing

This closet door guide is constructed from nylon and comes affixed to an adjustable steel bracket. It features a bottom mount design that fits on Acme and other similar styled doors. This guide also acts as corner bracket for steel frame bypassing doors.

• Nylon guide with steel bracket
• Adjustable bottom mount design
• Used by several manufacturers
• Acts as a corner bracket for steel framed by-pass doors
• Provides smooth operation
• For further dimensional information, please see the line drawing

This kit includes 2 drawer track guides that are constructed of plastic and come in a green color. These guides are used to replace damaged or missing drawer guides that have a 1-1/8 in. wide x 5/16 in. tall opening in the plastic guide. These guides are designed to fit 1-1/8 in. x 9/32 in. tracks to provide drawer alignment and smooth operation. The kit also includes white plastic saddles that are used to replace worn or missing guide buttons. These plastic saddles allow the drawers to glide easily when opening and closing, while at the same time preventing wear on the cabinet�s face frame or opening. The saddles install into the inside lower left and right corners of the drawer face opening with the fasteners provided within each kit. This kit includes enough parts to repair 2 drawers (with matching track and guide dimensions).

• Used to replace damaged or missing drawer guides that require a 1-1/8 in. x 5/16 in. guide opening
• Is 1-1/8 in. x 5/16 in
• Mounts to the back of the drawer
• Green molded plastic with white saddles
• Includes 2 guides and 4 side saddles
• Mounting hardware included
• A Phillips head screwdriver is required for Installation
• For further dimensional information, please see the line drawing

These drawer slide roller assemblies are constructed of plastic tires and steel ball bearings. It features a 1/4" 20 mounting stud and the 1-1/8 in. outside diameter tire has a convex edge. This multi-use roller is designed for use as a replacement roller for metal drawer slide systems. Frequently used to repair damaged or missing rollers found in file cabinet drawer tracks. These rollers are easy to install and include to assemblies per package.

• Typically found on drawers and cupboard shelving units
• 1-1/8 in. diameter roller
• Features a 1/4 in. offset hub with a 1/4-20 x 3/8 in. threaded mounting stud
• White nylon roller with ball bearings
• Ball bearing feature allows for smoother operation
• Hex nut included
• Adjustable wrench required for installation
• For further dimensional information, please see the line drawing

This drawer track delta guide is constructed from white polyethylene. It features a large bearing area for heavily loaded drawers. This type of guide has a 6-point contact that reduces lateral movement of the drawer.

• Used by a variety of drawer manufacturers
• Large bearing area for heavily loaded drawers
• 6 point contact reduces lateral movement
• White polyethylene construction
• Easy to install
• Mounting hardware included
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

These guides are constructed from orange plastic. They help in keeping your drawers aligned and make for a smoother operation. Contains enough parts to repair two drawers. Fits a 9/32 in. x 1-1/8 in. track.

• Used with tracks 9/32 in. x 1-1/8 in
• Includes four side saddles for smooth operation of drawer
• Contains two support plates
• Orange plastic construction
• Easy to install
• Mounting hardware included
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

Why struggle with a drawer that won�t open or close properly when you can simply replace the slides? Whether you need to replace damaged or missing slides or are installing them new for the first time, Prime-Line part R 7210 drawer slide kit fits most bottom/side-mounted drawer systems and is for use in 16 in. deep drawer cabinets. These bottom mount drawer slides can be installed in drawer cabinets with face frames and without.
Whether you are installing new drawers or repairing one that won't open or close properly, Prime-Line drawer Slide Kit fits most bottom/side-mounted drawer systems. The drawer slide kit is constructed of steel tracks with a white powder coated finish and self-lubricating plastic rollers.
SELF-CLOSING DESIGN - The smooth-gliding tracks features a self-closing design that commences at the final 2-1/2 in. from the end of the 15-3/4 in. long tracks when closing
EASY TO INSTALL - Installation is quick and easy, and the kit contains all necessary fasteners. Installation instructions are included and also available on Prime-Line's website.
The maximum load capacity for the drawer slide kit is 75 lbs. and is for use in 16 in. deep drawer cabinets. It features a positive stop in the closed position and a double stop in the extended position that locks your drawer open, so it cannot be pulled too far out and fall off the tracks.
INSTALLATION TIP - The clearance required between the drawer and the drawer opening for these slides is: 1/2 in. on left and right sides, 1/4 in. at the bottom and 5/8 in." at the top

This swing bar door guard will increase peace of mind when answering the door by allowing the door to be cracked open slightly for viewing. When engaged, a ball on the keeper interlocks with the bar lock and prevents an intruder from pushing their way through. Although a standard swing bar door guard can add great security to your home, condo, apartment/flat, or hotel room, there has been some concern over the wide availability of emergency release tools, which are meant to release swing bar door guards in cases of emergency. We have improved upon the standard door guard design and added an innovative backup thumb turn security lock that blocks the release tool from disengaging the door guard latch. In cases of emergency, hotel security or emergency crews can pop the thumb turn off of the unit by applying approximately 100 pounds of force to the door. Note that 100 lbs. Of force is much greater than a simple kick in, so the emergency release feature does not compromise your security. Additionally, after the thumb turn lock breaks away, the unit still operates as a traditional swing bar door lock and a specially designed Anti-Lockout emergency access tool is required to swing the door guard out of place. To help prevent forced entry into your home, it is always a good idea to engage the backup thumb turn lock whenever you are not actively using your door. Defender Security by Prime-Line offers a full line of security hardware designed to protect your home and loved ones. All are keyed the same.

• Used on doors and drawers that are 5/16 in. thick
• Allows you to secure drawer or cabinet
• Can be special ordered to be keyed the same
• Durable diecast and steel construction with a bright brass finish

COMPLEMENTS YOUR SLIDING PATIO DOOR, This hook style door handle is constructed of mixed materials, including a surface mounted wood pull, making it the perfect choice for your black or dark bronze sliding door

• Contains 1 lock, 3 cams, 1 trim collar, 1 spur washer, 2 rotation washers, 1 lock nut and 2 keys
• Body of this lock is 5/8 in. diameter with a face of 7/8 in. diameter
• For further dimensional information, please see the line drawing

Flush mounting drawer and cabinet lock. For material thickness of 7/8". 5/16" bolt throw. Requires 7/8" diameter hole. 2 keys included. Steel brass-plated die-cast housing. Uses Y13 key blank. SKU 202444.

• No. U 9947
• Color: Brass
• Material: Steel
• Hole Diameter: 7/8"
• Maximum Door Thickness: Up to 7/8"
• Keyed: Keyed different
• Pkg Qty: 1
• Package Type: Card

Stainless steel face; plated die-cast housing. Chrome finish. Provided with straight and offset cams. Installs in 3/4" hole. 90 deg. and 180 deg. stops. Includes 1-1/8" offset and 1-3/8" straight cams. 2 keys included. When ordering full cartons or nonkeyed alike locks, members may receive sets of 2 keyed alike. Uses Yale Y-11 keyway.

• No. U 9945
• Size: 13/16"
• Color: Chrome
• Material: Steel
• Hole Diameter: 3/4"
• Maximum Door Thickness: Up to 13/16"
• Keyed: Keyed different
• Package Quantity: 1
• Package Type: Card

These cabinet knob backplates are constructed of stamped steel and come in a polished brass plated finish. Backplates like these are used on both cabinet doors and drawer faces to prevent the wearing of finished wood, and the unsightly accumulation of dirt and grime. They feature a large 2-13/16 in. outside diameter and they project outward a total of 3/16 in. These cabinet knob backplates do not include any installation fasteners, but they come with pre-punched holes for quick and easy installation.

• Used beneath cabinet knobs to prevent scratches to finished wood, and to prevent the unsightly accumulation of dirt and grime
• 2-13/16 in. outside diameter x 3/16 in. projection
• Polished brass finish
• Stamped steel construction
• Easy to install with a few simple tools
• For further dimensional information, please see the line drawing

These cabinet knob backplates are constructed of stamped steel and come in a chrome plated finish. Backplates like these are used on both cabinet doors and drawer faces to prevent the wearing of finished wood, and the unsightly accumulation of dirt and grime. They feature a large 2-13/16 in. outside diameter and they project outward a total of 3/16 in. These cabinet knob backplates do not include any installation fasteners, but they come with pre-punched holes for quick and easy installation.

• Used beneath cabinet knobs to prevent scratches to finished wood, and to prevent the unsightly accumulation of dirt and grime
• 2-13/16 in. outside diameter x 3/16 in. projection
• Chrome plated finish
• Stamped steel construction
• Easy to install with a few simple tools
• For further dimensional information, please see the line drawing

This drawer and cabinet lock is constructed of diecast and steel components and it comes in a stainless steel finish. Features a 3/4 in. outside cylinder diameter with a 1-3/8 in. length that will accommodate up to 1 in. thick panels. Can be mounted to metal or wood; door and/or drawer panels, and it comes complete with 3 cams, a trim collar, 2 reversible rotation washers, 2 keys and fasteners. These are keyed alike and they uses Yale Y-11 keyway. Others have used these to replace damaged locks in work truck tool boxes and gumball machines.

• Used to secure cabinet doors and drawers up to 1 in. thick
• 3/4 in. outside diameter x 1-3/8 in. long cylinder. Fits on 1 in. maximum panel thickness
• Can be special ordered to be keyed differently
• Durable diecast and steel construction with a stainless steel finish
• All hardware included for installation
• Contains 1 lock, 3 cams, 1 trim collar, 1 spur washer, 2 rotation washers, 1 lock nut and 2 keys
• Body of this lock is 1-3/8 in. diameter with a face of 7/8 in. diameter
• For further dimensional information, please see the line drawing

These rear drawer track brackets are constructed of a thick, durable plastic and they come in white, left and right-hand pair. They are designed to support and maintain alignment of bottom/side-mounted steel drawer slides (like Prime-Line parts R 7210 thru R 7214). They feature an easy to install design, with a 2-7/8 in. socket depth to allow for front to back adjustment of the drawer slides. This pair of drawer track back plates includes the installation fasteners, and they have a maximum load rating of 75 lbs. per pair. These rear drawer replacement track sockets are simple to install and are used by many.

• Typically used on side mounted, steel ball bearing drawer guides
• Mounted on the cabinet behind the drawer
• Depth of sockets allows for small adjustment from front to back on rail
• Made of durable white plastic
• Can also be used for bottom mount drawer slides
• Mounting hardware included
• A Phillips head screwdriver is required for installation
• For further dimensional information, please see the line drawing

This kit is constructed of steel and plastic components and it includes all the parts necessary to repair one wooden drawer track system. Track is constructed of a 22-1/2 in. piece of rolled-edge galvanized steel that can be cut down to size. Roller assemblies are constructed of steel brackets with plastic wheels. The guides are constructed of plastic. Rollers are used to replace worn or missing parts, The rollers install into the inside lower left and right corners of the drawer.

• Kit contains mixed materials like plastic and steel, and wood
• Used to replace damaged or missing guides and track
• Track is 22-1/2 in. and can be cut down to fit application
• Guides are constructed of plastic
• Rollers have metal housing with plastic wheels
• For further dimensional information, please see the line drawing

This plastic backplate can be inverted for self-adjusting application. For use on hat-section style track and rolled edge and most other center mount tracks.

• Drawer track back plate
• Plastic construction
• Purple in color
• Guide length is 2-3/4 in
• Mounts on the back of the cabinet to support the track
• For further dimensional information, please see the line drawing

This 7/8 in. diameter nylon wheel features a top hung center grooved design. It comes secured to a 5/16 in. offset adjustable steel bracket. Fits old style Kenna Frame, Crawford, and Press-Rite doors.

• 7/8 in. outside diameter center groove nylon wheel
• 5/16 in. Offset Adjustable Steel Bracket
• Used by several manufacturers
• Zinc plated finish
• Provides smooth operation
• For further dimensional information, please see the line drawing

This drawer track guide kit is constructed from white plastic. These guides and glides are designed to restore the smooth operation of your track mounted drawers. They come complete with fasteners for a quick and easy installation.

• For use on rolled edge metal tracks with a 21/32 in. x 1-1/8 in.
• Helps to keep drawers aligned
• Mounts to the back of the drawer
• White molded plastic
• Includes 2 guides and 4 side saddles
• Mounting hardware included
• A Phillips head screwdriver is required for Installation
• For further dimensional information, please see the line drawing

This standard duty capacity closer is used on out-swinging wood or metal doors. It also features an adjustable closing speed. Best used on medium-weight installations.

• Used on medium-weight doors
• 10-1/2 in. tube length
• White painted color
• Constructed of steel and diecast components
• Installation fasteners included
• For further dimensional information, please see the line drawing

This Rim Cylinder Lock by Prime-Line Products is constructed from heavy-duty zinc diecast materials and steel components, whose face comes in a corrosion-resistant, and brass-plated finish. This rim cylinder lock includes a beautifully finished trim ring, a strong and durable mounting plate, installation screws and 2 brass keys. Another great feature of this lock is that it can be re-keyed to fit a different key cut, and it can be used to replace Kwikset, Weiser or Weslock locks.

• Constructed of diecast, steel and brass components
• Comes in a corrosion resistant, brass plated finish to match existing hardware
• Designed for use with a variety of deadlocks and deadbolt security hardware
• Features two keys, trim ring, mounting plate and installation fasteners
• Easy to install with only a few simple tools
• For further dimensional and specification information, please see the line drawing

These shelf support pegs are constructed from steel and come plated in a brass plated finish. They are designed to fit into 1/4 in. diameter holes, for use in cabinets and bookshelves. These pegs feature a 20 lb. maximum safe load capacity (per peg) and can be used for many applications. These shelf support pegs are easy to install and are used by many manufacturers.

• Used to support adjustable shelving
• 1/4 in. outside peg diameter, with 1/2 in. x 11/16 in. seat
• Brass plated finish
• Steel construction
• Easy to install
• For further dimensional information, please see the line drawing

This drawer and cabinet lock is constructed of diecast and steel components and it comes in a stainless steel finish. Features a 3/4 in. outside cylinder diameter with a 7/8 in. length that will accommodate up to 9/16 in. thick panels. Can be mounted to metal or wood; door and/or drawer panels. It comes complete with 3 cams, a trim collar, 2 reversible rotation washers, 2 keys and fasteners. This model number is keyed different and it uses Yale Y-11 keyway. Others have used these to replace damaged locks in work truck tool boxes and gumball machines.

• Used to secure cabinet doors and drawers
• 3/4 in. outside diameter x 7/8 in. long cylinder. Fits on 9/16 in. maximum panel thickness
• Stainless steel finish
• Diecast cylinder with steel cams

COMPLEMENTS YOUR BLACK SLIDING PATIO DOOR - This mortise hook style door handle is constructed of black painted diecast materials, making it the perfect choice for your black sliding door

• Can be mounted to wood or metal door and drawer panels
• Installation is quick and easy with a few simple tools
• For further dimensional information, please see the line drawing

This 13/16 in. diameter roller features a 3-1/2 in. high bracket. It mounts on the left side of your drawer when viewed from the rear. Contains 2 rollers and includes fasteners for a quick and easy installation.

• Mono-rail roller for drawer slide systems
• Left hand design
• Plastic roller
• Used on drawers
• Provides smooth operation
• For further dimensional information, please see the line drawing