FREE shipping on orders over $49!* Details
- All Products
- Bath
- Tile
- Finish: High-Gloss
High-Gloss Free-Form Tile
Sort by:
Price
26 Results
Mosaic Porcelain Tile Mancala Pebble Series Floor Wall Pool Bathroom Shower, Royby Flooring Supply Shop(2)
$58
Free Shipping
MOSAIC PORCELAIN TILE MANCALA PEBBLE SERIES - Royal Blue
Pool Rated for use in Swimming Pools
** Price is per Piece **
For use in
Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Tile Maintenance and More
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Pool Rated for use in Swimming Pools
** Price is per Piece **
- Material: Handmade Porcelain
- Piece Size: 11 1/2" x 11 1/2"
- Sq Ft Per Piece: 0.92
- Thickness: 1/4"
- Color: Royal Blue
- Finish: Glossy
For use in
- Pools, Pool Liners
- Interior Dry Walls
- Interior Floors
- Shower Walls, Shower Floors
- Exterior Walls, Exterior Floors
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Pools, Pool Liners, Shower Walls, Interior Dry Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
MAINTENANCE & CARE
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Tile Maintenance and More
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Mix Colors Pebble Porcelain Mosaic Tileby districtII
$20
- Price is per sheet
- Color: Mix Colors, white, red, yellow, blue, green and beige
- Dimension: 12" x 12 Sheet
- Tile Size: Mixed
- Thickness: 6 mm
- Surface: Glossy Glazed
- Material: Porcelain
Pebble Blue 12 x 12by Fancy Decorative Mosaic
$33
Free Shipping
Sponsored- Pebble Blue 12 x 12 - A mix of blue and white marble with Glossy glass in a pebble-like mosaic.
- Suggested Grout Color: Bostik Dimension Diamond H600
Mosaic Porcelain Tile Mancala Pebble Series - Sea Pebble - Floor Wall Tileby Flooring Supply Shop
Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
$58
Free Shipping
- Mosaic Porcelain Tile Mancala Pebble Series - Sea Pebble
- Pool Rated for use in Swimming Pools
- ** Price per Sheet ***
- Material: Handmade Porcelain
- Piece Size: 11 1/2" x 11 1/2"
- Sq Ft Per Piece: 0.92
- Thickness: 1/4"
- Colors: Multi
- Finish: Glossy
- Suited for: Residential, Commercial, Light Commercial
- For use in
- Pools, Pool Liners
- Interior Dry Walls
- Interior Floors
- Shower Walls, Shower Floors
- Exterior Walls, Exterior Floors
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Pools, Pool Liners, Shower Walls, Interior Dry Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
- Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.
- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
- Maintenance & Care
- Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
- Tile Maintenance and More
- Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Mosaic Porcelain Tile Mancala Pebble Series - Seaworld - Pool Ratedby Flooring Supply Shop
Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
$58
Free Shipping
- Mosaic Porcelain Tile Mancala Pebble Series - Seaworld
- Pool Rated for use in Swimming Pools
- Multi Green & Beige Pebble Shape Handmade Porcelain Mosaic.
- Price per Sheet
- Material: Handmade Porcelain
- Piece Size: 11 1/2" x 11 1/2"
- Sq Ft Per Piece: 0.92
- Thickness: 1/4"
- ColorsBlue and Earth tons
- Finish: Glossy
- Suited for: Residential, Commercial, Light Commercial
- For use in
- Pools, Pool Liners
- Interior Dry Walls
- Interior Floors
- Shower Walls, Shower Floors
- Exterior Walls, Exterior Floors
- Pool rated and acceptable for use on shower walls.
- The polyurethane cord backing makes installation easy.
- For use in Pools, Pool Liners, Shower Walls, Interior Dry Walls
- Installation Guide
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
- Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.
- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8” (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer’s recommendations for application instructions.
Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout & Tile neutral cleaner.
- Maintenance & Care
- Required to use PH Neutral Cleaner to clean the tile and grout, such as Grout & Tile Neutral Cleaner
- Tile Maintenance and More
- Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
Pele Glazed Pebble Blend Series Royal Ocean Mosaic Stone Tile for Floors Walby Flooring Supply Shop
$62
Free Shipping
PELE GLAZED PEBBLE BLEND SERIES - ROYAL OCEAN
*** PRICE IS PER SHEET ***
Royal Ocean and Lava Blend
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
*** PRICE IS PER SHEET ***
Royal Ocean and Lava Blend
- Material: Basalt
- Sheet Size: 12"x12"
- Piece Size: Random
- Finish: Glossy
- Backing: Mesh
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Glazed Pele Pebbles can be used on interior wall applications.
- Sealing is required before and after grouting.
- A natural stone, water based sealer is recommended.
- We recommend sealing with a penetrating sealer prior to installation.
Mosaic Marble and Glass Tile, Pebble Look, Oceanby Flooring Supply Shop
Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer's recommendations for application instructions.
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
$83
Free Shipping
- Marble and Glass in Pebble look - Ocean
- A blend of Thassos Marble with white glass in a Pebble layout style
- ** Price is per Sheet ***
- Material: Marble and Glass
- Sheet Size: 12" x 12" (1 sq ft per sheet)
- Thickness: 3/8"
- Colors: Blue White Grey
- Finish: Glossy
- Uses: Interior Dry Walls, Interior Floors (Residential), Shower Walls, Shower Floors (Residential)
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8"away from any naked flame.
- Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
- Verifying Dye Lot Consistency: The owner or end user is responsible for determining the acceptability of the product. Due to the handmade, artistic nature of our product, variation in color, shade, tone, and size is normal.
- Upon delivery, open and inspect each box of tile.
- Verify dye lot consistency in the following manner. To establish color control samples, randomly select 5 pieces from your order from different boxes.
- To assure shade variations are acceptable check, the remaining sheets or field tile in your order against the control samples, prior to installation.
- If ordering additional materials. Sample shall be sent to help attempt to match previously ordered material.
- Setting Material: Because of the translucent nature of glass, the color of the bonding material will impact the ultimate look of the tile. We highly recommend the use of white polymer modified white thin-set.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate™ GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Acceptable Grout:
- MAPEI: Keracolor S
- Bostik: Dimensions and TruColor
- LATICRETE: 1500 Sanded Grout
- TEC: AccuColor Premium Sanded Tile Grout
- Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
- Drilling: Using a drill bit designed for glass is recommended. When drilling the hole, keep the bit and hole lubricated to prevent chipping. Start by drilling from both ends of the tile, starting with the back and drilling half the depth of the tile. Then, turn the tile over and complete the hole is recommended. This will prevent the glass from chipping as the drill bit exits the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8" (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer's recommendations for application instructions.
- Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout and Tile neutral cleaner.
- Maintenance and Care
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
- Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
The Coin Series Glass Tile in 4 Colors Wall Floor Mosaic Tile, Blue Lagunaby Flooring Supply Shop
$75
Free Shipping
THE COIN SERIES GLASS TILE
Installation Instructions
Colors:
- Tan - Tan Beige & Light Brown Broken Glass with Rainbow Round Glass Inserts.
- Blue Laguna - Blue Irregular Broken Glass in Light Blue Color
- Royal - Blue , Tan Irregular Broken Glass in Light Blue Color
- Light Grey - Grey Irregular Broken Glass in White & Light Grey Color.
- Material: Glass
- Sheet Size: 11" x 11 1/2"
- SqFt Per Piece: 0.88
- Thickness: 3/8"
- Finish: Glossy
- Interior Dry Walls, Shower Walls, Residential, Commercial, Light Commercial
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials & Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
- Do not cover/protect the Victoria Metals with adhesive tape of any kind.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Sealing Guide:
- Sealing prior to grouting is recommended for all stone mosaics.
- Glass (see note below), Stainless Steel, Antique Copper and Aluminum mosaics do not require sealing.
- Note: Pre sealing prior to setting is necessary when installing Barossa Valley Crystal Glass.
- Note: Only use water based sealers with Sydney Harbor Metals.
- Note: When sealing Botany Bay pebbles expect some darkening of the color. Test sealer on a sample area first.
- Tile Maintenance and More
Pele Glazed Pebbles Series Sea Turtle Mosaic Stone Tile for Floors Wallsby Flooring Supply Shop
$76
Free Shipping
PELE GLAZED PEBBLES SERIES - SEA TURTLE
*** PRICE IS PER SHEET ***
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
*** PRICE IS PER SHEET ***
- Material: Basalt
- Sheet Size: 12"x12"
- Piece Size: Random
- Finish: Glossy
- Backing: Mesh
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Glazed Pele Pebbles can be used on interior wall applications.
- Sealing is required before and after grouting.
- A natural stone, water based sealer is recommended.
- We recommend sealing with a penetrating sealer prior to installation.
Pele Glazed Pebble Blend Series Blue Hawaiian Mosaic Stone Tile for Floors Wby Flooring Supply Shop
$62
Free Shipping
PELE GLAZED PEBBLE BLEND SERIES - BLUE HAWAIIAN
*** PRICE IS PER SHEET ***
Blue Hawaiian and Lava Blend
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
*** PRICE IS PER SHEET ***
Blue Hawaiian and Lava Blend
- Material: Basalt
- Sheet Size: 12"x12"
- Piece Size: Random
- Finish: Glossy
- Backing: Mesh
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Glazed Pele Pebbles can be used on interior wall applications.
- Sealing is required before and after grouting.
- A natural stone, water based sealer is recommended.
- We recommend sealing with a penetrating sealer prior to installation.
Metro 1 in x 1 in Glass Square Mosaic in Glossy Pebble Grayby GBM Manufacturing
$10.95/sq ft.
Free Shipping
Classic design that will never go out of style. Unmatched glow of glass adds light and shine. Radiates natural sunlight and energizes your environment. Adds delicate beauty to your room. Unlimited design options and patterns.
Mosaics Tile Marble Toscano Pebble look - Crystal Ocean - for Floors Wallsby Flooring Supply Shop
$78
Free Shipping
- MOSAICS MARBLE TOSCANO APHRODITE PEBBLE LOOK - CRYSTAL OCEAN
- A mix of Blue Crystal and Thassos Marble in heart-shaped pieces
- Material: Marble
- Piece Size: 12" x 12"
- Individual Size: 1/2", 1 1/4 and 2 1/4
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Mixed white and light blue
- Finish: Glossy
Pele Glazed Pebble Blend Series Teal Tide Mosaic Stone Tile for Floors Wallsby Flooring Supply Shop
$62
Free Shipping
PELE GLAZED PEBBLE BLEND SERIES - TEAL TIDE
*** PRICE IS PER SHEET ***
Teal Tide and Lava Blend
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
*** PRICE IS PER SHEET ***
Teal Tide and Lava Blend
- Material: Basalt
- Sheet Size: 12"x12"
- Piece Size: Random
- Finish: Glossy
- Backing: Mesh
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Glazed Pele Pebbles can be used on interior wall applications.
- Sealing is required before and after grouting.
- A natural stone, water based sealer is recommended.
- We recommend sealing with a penetrating sealer prior to installation.
Pele Glazed Pebbles Series Royal Ocean Mosaic Stone Tile for Floors Wallsby Flooring Supply Shop
$76
Free Shipping
PELE GLAZED PEBBLES SERIES - ROYAL OCEAN
***** PRICE PER SHEET *****
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
***** PRICE PER SHEET *****
- Material: Basalt
- Sheet Size: 12"x12"
- Piece Size: Random
- Finish: Glossy
- Backing: Mesh
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Glazed Pele Pebbles can be used on interior wall applications.
- Sealing is required before and after grouting.
- A natural stone, water based sealer is recommended.
- We recommend sealing with a penetrating sealer prior to installation.
Pele Glazed Pebble Blend Series Sea Turtle Mosaic Stone Tile for Floors Wallby Flooring Supply Shop
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
$62
Free Shipping
- PELE GLAZED PEBBLE BLEND SERIES - SEA TURTLE
- Sea Turtle and Lava Blend
- Material: Basalt
- Sheet Size: 12"x12"
- Piece Size: Random
- Finish: Glossy
- Backing: Mesh
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Glazed Pele Pebbles can be used on interior wall applications.
- Sealing is required before and after grouting.
- A natural stone, water based sealer is recommended.
- We recommend sealing with a penetrating sealer prior to installation
Pele Glazed Pebbles Series Blue Hawaiian Mosaic Stone Tile for Floors Wallsby Flooring Supply Shop
$75
Free Shipping
PELE GLAZED PEBBLES SERIES - BLUE HAWAIIAN
**** PRICE IS PER SHEET ****
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
**** PRICE IS PER SHEET ****
- Material: Basalt
- Sheet Size: 12"x12"
- Piece Size: Random
- Finish: Glossy
- Backing: Mesh
Basalt is extracted from a deep layer of solidified volcanic flow, these pebbles are tumbled and then hand glazed in vibrant colors. Once glazed, the pebbles are fired at 1000 degrees Celsius allowing a strong bond much like a ceramic tile.
Pele Pebbles are an artisanal product and are decorated by hand, therefore may have shade variations that are not defects, but characteristics of the product.
Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Glazed Pele Pebbles can be used on interior wall applications.
- Sealing is required before and after grouting.
- A natural stone, water based sealer is recommended.
- We recommend sealing with a penetrating sealer prior to installation.
Truu Design Plastic Peel/Stick Backsplash Wall Tile Set Multi-Color (Set of 6)by Truu Design
$43
Free Shipping
There is nothing more comforting and welcoming than classic, timeless style walls. You can never go wrong with a nice herringbone or subway accent wall or kitchen backsplash. Featuring a real ceramic wall can be quite expensive and requires a lot of work—but it doesn’t have to be with our peel and stick wall tiles. Our self-adhesive wall stickers are made of durable PVC (epoxy), making them water-resistant and mold-resistant. The glossy finish allows for these tiles to resemble real traditional ceramic/porcelain tiles. Whether you want to create a bold, striking look in your bathroom, or give your kitchen backsplash a beautiful dimensional look, these PVC epoxy wall tiles are a fun and affordable solution. They come in a set of 6 and they can easily be cut/trimmed with a utility knife.
Features :
- Set: comes in a box of 6 premium quality multi-color wall tiles, suitable for smooth and clean surfaces
- Premium Quality: wall peel and stick backsplash tiles are made of high-quality, durable eco-friendly PVC plastic, water-resistant and mold resistant which never turn yellow with time
- Versatile: use the peel and stick backsplash wallpaper for kitchen sink walls, bathroom backsplash, bedroom walls, laundry room, staircase, or on any other flat surfaces that are non-porous surfaces
- Easy DIY: simply peel off the backing and stick the self-adhesive backsplash tiles onto the desired spot without extra glue, no grout, no mess and no special tools or experience required
- Feature: easier to work with than big rolls or larger tiles as the size allows for a good stitching installation, can be bent to corner or cut by a sharp utility knife to fit perfectly
- Perfect Size: Each backsplash tile measures 10"L x 10"H in dimensions (approx. covers 4.17 sq. ft. per carton)
Specifications :
- Product Weight : 1.3 lbs
Truu Design Plastic Peel/Stick Backsplash Wall Tile Set Multi-Color (Set of 6)by Truu Design(6)
$43
Free Shipping
There is nothing more comforting and welcoming than classic, timeless style walls. You can never go wrong with a nice herringbone or subway accent wall or kitchen backsplash. Featuring a real ceramic wall can be quite expensive and requires a lot of work—but it doesn’t have to be with our peel and stick wall tiles. Our self-adhesive wall stickers are made of durable PVC (epoxy), making them water-resistant. The glossy finish allows for these tiles to resemble real traditional ceramic/porcelain tiles. Whether you want to create a bold, striking look in your bathroom, or give your kitchen backsplash a beautiful dimensional look, these PVC epoxy wall tiles are a fun and affordable solution. They come in a set of 6 and they can easily be cut/trimmed with a utility knife.
Features :
- Set: comes in a box of 6 premium quality multi-color wall tiles, suitable for smooth and clean surfaces
- Premium Quality: wall peel and stick backsplash tiles are made of high-quality, durable eco-friendly PVC plastic, and water-resistant which never turn yellow with time
- Versatile: use the peel and stick backsplash wallpaper for kitchen sink walls, bathroom backsplash, bedroom walls, laundry room, staircase, or on any other flat surfaces that are non-porous surfaces
- Easy DIY: simply peel off the backing and stick the self-adhesive backsplash tiles onto the desired spot without extra glue, no grout, no mess and no special tools or experience required
- Feature: easier to work with than big rolls or larger tiles as the size allows for a good stitching installation, can be bent to corner or cut by a sharp utility knife to fit perfectly
- Perfect Size: Each backsplash tile measures 10"L x 10"H in dimensions (approx. covers 4.17 sq. ft. per carton)
Specifications :
- Product Weight : 1.3 lbs
Truu Design Plastic Peel/Stick Backsplash Wall Tile Set Multi-Color (Set of 6)by Truu Design(1)
$43
Free Shipping
There is nothing more comforting and welcoming than classic, timeless style walls. You can never go wrong with a nice herringbone or subway accent wall or kitchen backsplash. Featuring a real ceramic wall can be quite expensive and requires a lot of work—but it doesn’t have to be with our peel and stick wall tiles. Our self-adhesive wall stickers are made of durable PVC (epoxy), making them water-resistant and mold-resistant. The glossy finish allows for these tiles to resemble real traditional ceramic/porcelain tiles. Whether you want to create a bold, striking look in your bathroom, or give your kitchen backsplash a beautiful dimensional look, these PVC epoxy wall tiles are a fun and affordable solution. They come in a set of 6 and they can easily be cut/trimmed with a utility knife.
Features :
- Set: comes in a box of 6 premium quality multi-color wall tiles, suitable for smooth and clean surfaces
- Premium Quality: wall peel and stick backsplash tiles are made of high-quality, durable eco-friendly PVC plastic, water-resistant and mold resistant which never turn yellow with time
- Versatile: use the peel and stick backsplash wallpaper for kitchen sink walls, bathroom backsplash, bedroom walls, laundry room, staircase, or on any other flat surfaces that are non-porous surfaces
- Easy DIY: simply peel off the backing and stick the self-adhesive backsplash tiles onto the desired spot without extra glue, no grout, no mess and no special tools or experience required
- Feature: easier to work with than big rolls or larger tiles as the size allows for a good stitching installation, can be bent to corner or cut by a sharp utility knife to fit perfectly
- Perfect Size: Each backsplash tile measures 10"L x 10"H in dimensions (approx. covers 4.17 sq. ft. per carton)
Specifications :
- Product Weight : 1.3 lbs
Sonoma Valley 12X12 Interlocking Mosaic, 20 Sheetsby Buytilesandmore
$14.25/sq ft.
Free Shipping
Sonoma Valley 4mm Interlocking Mosaic Tile strikes the perfect balance between traditional and contemporary with neutral colorways of brown, beige, and cream in crystallized glass and stone. Durable, low-maintenance, and highly versatile, there?s no better way to give your residential or light use commercial project signature style. The long, linear look of these tiles visually enlarges even the smallest of spaces, while light reflects off the glass to lighten and brighten any room. It?s perfectly suited for a kitchen backsplash, but why stop there? You can also use it on countertops, accent walls, shower walls, fireplace facades, and more. The truth is, wherever you choose to use this gorgeous tile the compliments are sure to follow. Tiles are mounted on mesh-backed sheets for a simplified installation that yields a professional look. For SAMPLE ORDERS - Order affordable samples before you place an actual full order. Samples are usually 4inch x 4inch or 6inch x 6inch based on the type of tile. These samples are just a representation of the actual tiles for you to see the color and texture of the tiles. Samples are shipped by Fedex / USPS ground service, sometimes the samples are not in good shape on delivery as they are individually packed and lack the proper safe packaging as the actual tile order. Nevertheless they solve the purpose of showing you the color, texture and the pattern of the tiles.
Glazed Mixed Quartz Moon Mosaic Tileby Faber Cnk Stone(41)
$12/sq ft.
Free Shipping
Each stone is carefully selected and hand-sorted according to color, size and shape in order to ensure the highest quality pebble tile available. The stones are attached to a sturdy mesh backing using non-toxic, environmentally safe glue. Because of the unique pattern in which our tile is created they fit together seamlessly when installed so you can't tell where one tile ends and the next begins!
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Usage:
Shower floor, bathroom floor, general flooring, backsplashes, swimming pools, patios, fireplaces and more. Interior & exterior. Commercial & residential.Details:
- Sheet Backing: Mesh
- Sheet Dimensions: 12x12
- Pebble size: Approx 3/4 to 2 1/2
- Thickness: Approx 3/8
- Finish: Glazed Quartz
- Number of Pieces Included: 1
- Sq. ft. per 1 Quantity: 1
- Mesh Backing
Sea Green Pebble Tileby Faber Cnk Stone(16)
$14/sq ft.
Free Shipping
Each pebble is carefully selected and hand-sorted according to color, size and shape in order to ensure the highest quality pebble tile available. The stones are attached to a sturdy mesh backing using non-toxic, environmentally safe glue. Because of the unique pattern in which our tile is created they fit together seamlessly when installed so you can't tell where one tile ends and the next begins!
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Usage:
Shower floor, bathroom floor, general flooring, backsplashes, swimming pools, patios, fireplaces and more. Interior & exterior. Commercial & residential.Details:
- Sheet Backing: Mesh
- Sheet Dimensions: 12x12
- Pebble size: Approx 3/4 to 2 1/2
- Thickness: Approx 1/2
- Finish: Green Natural
- Number of Pieces Included: 1
- Sq. ft. per 1 Quantity: 1
- Mesh Backing
Sliced Java Tan and White Pebble Tileby Faber Cnk Stone(9)
$15/sq ft.
Free Shipping
Each pebble is carefully selected and hand-sorted according to color, size and shape in order to ensure the highest quality pebble tile available. The stones are attached to a sturdy mesh backing using non-toxic, environmentally safe glue. Because of the unique pattern in which our tile is created they fit together seamlessly when installed so you can't tell where one tile ends and the next begins!
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Usage:
Shower floor, bathroom floor, general flooring, backsplashes, swimming pools, patios, fireplaces and more. Interior & exterior. Commercial & residential.Details:
- Sheet Backing: Mesh
- Sheet Dimensions: 12x12
- Pebble size: Approx 3/4 to 2 1/2
- Thickness: Approx 3/8
- Finish: Natural Sliced Tan and White
- Number of Pieces Included: 1
- Sq. ft. per 1 Quantity: 1
- Mesh Backing
Red Mosaic Tileby Faber Cnk Stone(5)
$14/sq ft.
Free Shipping
Each pebble is carefully selected and hand-sorted according to color, size and shape in order to ensure the highest quality pebble tile available. The stones are attached to a sturdy mesh backing using non-toxic, environmentally safe glue. Because of the unique pattern in which our tile is created they fit together seamlessly when installed so you can't tell where one tile ends and the next begins!
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Please note: This is a natural tile, as such will have fistulas and coloration varients that occur naturally depending on the cut of the stone.
Usage:
Shower floor, bathroom floor, general flooring, backsplashes, swimming pools, patios, fireplaces and more. Interior & exterior. Commercial & residential.Details:
- Sheet Backing: Mesh
- Sheet Dimensions: 12x12
- Pebble size: Approx 3/4 to 2 1/2
- Thickness: Approx 1/2
- Finish: Red Natural
- Number of Pieces Included: 1
- Sq. ft. per 1 Quantity: 1
- Mesh Backing
Pebble Gray Arabesque Glass Mosaic Tile, 12"x12"by Rocky Point Tile Co(8)
$23
Free Shipping
Bring a touch of elegance to your new new kitchen backsplash or bathroom with our Pebble Grey Arabesque Glass Tiles. These tiles are stunning! The color is a medium grey. This is probably as close to what a lot of people think of a as a 'true grey'. Consider mingling other colors in this series to add a little pop to your project! We also carry Pebble Grey in a 3x6 subway tile.
- Weight: 3.8 LBS/ Sq Ft
- Individual Glass Pieces: 6.25" x 5.25"
- Finish: High Gloss
- Number of Pieces Included: 1
- Sq. ft. Coverage: 1
- Mesh Backing
Truu Design Plastic Peel/Stick Backsplash Wall Tile Set Multi-Color (Set of 6)by Truu Design
$45
Free Shipping
There is nothing more comforting and welcoming than classic, timeless style walls. You can never go wrong with a nice herringbone or subway accent wall or kitchen backsplash. Featuring a real ceramic wall can be quite expensive and requires a lot of work—but it doesn’t have to be with our peel and stick wall tiles. Our self-adhesive wall stickers are made of durable PVC (epoxy), making them water-resistant. The glossy finish allows for these tiles to resemble real traditional ceramic/porcelain tiles. Whether you want to create a bold, striking look in your bathroom, or give your kitchen backsplash a beautiful dimensional look, these PVC epoxy wall tiles are a fun and affordable solution. They come in a set of 6 and they can easily be cut/trimmed with a utility knife.
Features :
- Set: comes in a box of 6 premium quality multi-color wall tiles, suitable for smooth and clean surfaces
- Premium Quality: wall peel and stick backsplash tiles are made of high-quality, durable eco-friendly PVC plastic, and water-resistant which never turn yellow with time
- Versatile: use the peel and stick backsplash wallpaper for kitchen sink walls, bathroom backsplash, bedroom walls, laundry room, staircase, or on any other flat surfaces that are non-porous surfaces
- Easy DIY: simply peel off the backing and stick the self-adhesive backsplash tiles onto the desired spot without extra glue, no grout, no mess and no special tools or experience required
- Feature: easier to work with than big rolls or larger tiles as the size allows for a good stitching installation, can be bent to corner or cut by a sharp utility knife to fit perfectly
- Perfect Size: Each backsplash tile measures 10"L x 10"H in dimensions (approx. covers 4.17 sq. ft. per carton)
Specifications :
- Product Weight : 1.3 lbs
