- All Products
- Bath
- Tile
- Finish: Honed
Honed Free-Form Tile
- Pebbles Series Leaves Series - Aspen
- *** PRICE IS PER SHEET ****
- Material: Stone
- Sheet Size: 12" x 12"
- Piece Size: Random
- Finish: Honed
- Backing: Mesh
- Leaves mosaics on mesh backing. Create features or cut down to use as borders.
- Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8”away from any naked flame.
Setting Materials & Methods:
- Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.
- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
- Always cut the Victoria Metals with finished side down. During the cutting process, feed the aluminum product through the blade at an extremely slow speed to avoid grabbing.
- Do not cover/protect the Victoria Metals with adhesive tape of any kind.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Sealing prior to grouting is recommended for all stone mosaics.
- Glass (see note below), Stainless Steel, Antique Copper and Aluminum mosaics do not require sealing.
- Note: Pre sealing prior to setting is necessary when installing Barossa Valley Crystal Glass.
- Note: Only use water based sealers with Sydney Harbor Metals.
- Be sure to order enough tile for your entire job. Over-estimating the square footage on a project will allow for unusual shapes, miscalculations and broken tiles on the job. Recommends manufacturer a minimum of 10% wastage allowance
- Using an enhancing sealer will darken the color of these stones!
- We recommend sealing with a penetrating sealer prior to installation.
- Title: Arctic White Panel 3D Honed 6X24, Marble, Ledgers
- Size: 6x24, SQFT per piece: 1, Height: 1, Length: 6, Width: 24
- Sku: NewMSPearl Drop_50
- Material: MARBLE
- Category: LEDGERS
- Finish:HONEDMatching corners are available to finish off projects.
- Title: Arctic White Panel 3D Hon "L" Panel 6X24, Honed, Marble, Ledgers
- Size: 6x24, SQFT per piece: 1, Height: 1, Length: 6, Width: 24
- Sku: NewMSPearl Drop_49
- Material: MARBLE
- Category: LEDGERS
- Finish:HONEDMatching corners are available to finish off projects.
- Calacatta Gold Honed Marble Mini Versailles Pattern Mosaic Tile
- Design Type: Marble
- Type: Honed Finish
- Design: Mosaic Tiles
- Color: White
- Material Type:Marble
- We sell by: sheet
- Width: 12 Height: 12 Thickness:0.375
- Chip Size (If available)
- Application: Bathroom, Bedroom, Kitchen indoor, and outdoor tiles.
- Product Code:Fancy_group_481
- Product Code: Fancy_group_481
- Sold By Unit: Box
- Coverage Area: 10 FT (square-feet)
- Number of Pieces included in 1 Quantity: 10
- Code: Fancyoption_3929
- Pebbles Series Leaves Series - Woodland Blend
- ** PRICE PER SHEET ***
- Material: Stone
- Sheet Size: 12" x 12"
- Piece Size: Random
- Finish: Honed
- Backing: Mesh
- Leaves mosaics on mesh backing. Create features or cut down to use as borders.
- Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8”away from any naked flame.
Setting Materials & Methods:
- Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.
- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
- Always cut the Victoria Metals with finished side down. During the cutting process, feed the aluminum product through the blade at an extremely slow speed to avoid grabbing.
- Do not cover/protect the Victoria Metals with adhesive tape of any kind.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Sealing prior to grouting is recommended for all stone mosaics.
- Glass (see note below), Stainless Steel, Antique Copper and Aluminum mosaics do not require sealing.
- Note: Pre sealing prior to setting is necessary when installing Barossa Valley Crystal Glass.
- Note: Only use water based sealers with Sydney Harbor Metals.
- Be sure to order enough tile for your entire job. Over-estimating the square footage on a project will allow for unusual shapes, miscalculations and broken tiles on the job. Recommends manufacturer a minimum of 10% wastage allowance
- Using an enhancing sealer will darken the color of these stones!
- We recommend sealing with a penetrating sealer prior to installation.
- Title: Milano White Oak Splitface " L" Panel 6X18", Marble, Ledgers
- Size: 6x18, SQFT per piece: 0.75, Height: 1.25, Length: 6, Width: 18
- Sku: NewMSPearl Drop_142
- Material: MARBLE
- Category: LEDGERS
- Aphrodite Calacatta Gold Honed 12x12 - Calacatta and Thassos Marble in heart shape pieces.
- Suggested Grout Color: Bostik Trucolor White H152
Design Type:
- Design Type: Honed Finish
Design:
- Color: Carrara White
- Material Type:Marble
- We sell by: sq.ft.
- Width: 12 Height: 12 Thickness:0.38
- Chip Size (If available)
- Application: Bathroom, Bedroom, Kitchen indoor, and outdoor tiles.
- Product Code:Fancy_group_1190
- Product Code: Fancy_group_1190
- Sold By Unit: Box
- Coverage Area: 10 FT (square-feet)
- Number of Pieces included in 1 Quantity: 10
- Code: Fancyoption_4638
- Pebbles Series Leaves Series - Chestnut
- ** PRICE PER SHEET ***
- Material: Stone
- Sheet Size: 12" x 12"
- Piece Size: Random
- Finish: Honed
- Backing: Mesh
- Leaves mosaics on mesh backing. Create features or cut down to use as borders.
- Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8”away from any naked flame.
Setting Materials & Methods:
- Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.
- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
- Always cut the Victoria Metals with finished side down. During the cutting process, feed the aluminum product through the blade at an extremely slow speed to avoid grabbing.
- Do not cover/protect the Victoria Metals with adhesive tape of any kind.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Sealing prior to grouting is recommended for all stone mosaics.
- Glass (see note below), Stainless Steel, Antique Copper and Aluminum mosaics do not require sealing.
- Note: Pre sealing prior to setting is necessary when installing Barossa Valley Crystal Glass.
- Note: Only use water based sealers with Sydney Harbor Metals.
- Be sure to order enough tile for your entire job. Over-estimating the square footage on a project will allow for unusual shapes, miscalculations and broken tiles on the job. Recommends manufacturer a minimum of 10% wastage allowance
- Using an enhancing sealer will darken the color of these stones!
- We recommend sealing with a penetrating sealer prior to installation.
- Title: White Oak 3D Hon Corner " L" Panel 6X24, Honed, Marble, Ledgers
- Size: 6x24, SQFT per piece: 1, Height: 1.25, Length: 6, Width: 24
- Sku: NewMSPearl Drop_144
- Material: MARBLE
- Category: LEDGERS
Mosaics Marble Pebble look - Marquina Black
A Marble - Mix of Black and White in heart-shaped mosaic
Price per Sheet (1 sq ft)
- Material: Marble
- Piece Size: 12" x 12"
- Individual Size: 1/2", 1 1/4 and 2 1/4
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Black, White
- Finish: Honed
- Size: 1 3/4 x 3 1/2 inch pieces mounted on 12 1/4 x 12 1/4 (1 sq. ft.) sturdy mesh tile sheet
- 10 rows and 3 columns with 30 stones and 30 dots per sheet
- 1/16 inch grout width;
- Thickness: 5/16 inch;
- Finish: Honed (Matte);
Mosaics Marble Pebble look - Basalt Black
A Marble - Mix of Black and dark Grey in heart-shaped mosaic
Price per Sheet (1 sq ft)
- Material: Marble
- Piece Size: 12" x 12"
- Individual Size: 1/2", 1 1/4 and 2 1/4
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Black, Dark Grey
- Finish: Honed
- MOSAICS PEBBLE MARBLE THASSOS AND CARIBE QUARTZITE - ROSE
- Pebble stile mosaic made of Bardiglio Bluette Grey, Azul Caribe Quartzite and Greece White Thassos
- Material: Marble White Thassos and Caribe Quartzit
- Piece Size: 12"x12"
- Individual Size: Mix
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Mixed Rose
- Finish: Honed
- Use for Residential / Commercial, Interior Dry Walls, Interior Floors, Shower Walls, Shower Floors, Exterior Walls
- Installation Guide
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
Setting Materials and Methods:
Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. Maniscalco is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
A Onyx - Mix of Green, White and Honey Onyx in heart-shaped mosaic
Price per Sheet (1 sq ft)
- Material: Marble
- Piece Size: 12" x 12"
- Individual Size: 1/2", 1 1/4 and 2 1/4
- Sq Ft Per Piece: 1
- Thickness: 3/8"
- Colors: Green, White and Honey
- Finish: Honed
- Title: Florence Arctic White Panel 3D Hon "L" Panel 6X18, Honed, Marble, Ledgers
- Size: 6x18, SQFT per piece: 0.75, Height: 1, Length: 6, Width: 18
- Sku: NewMSPearl Drop_48
- Material: MARBLE
- Category: LEDGERS
- Finish:HONEDMatching corners are available to finish off projects.
- Title: Alaska Gray Panel 6X24, Splitface, Marble, Ledgers
- Size: 6x24, SQFT per piece: 1, Height: 1.25, Length: 6, Width: 24
- Sku: NewMSPearl Drop_40
- Material: MARBLE
- Category: LEDGERS
A mix of Carrara marble and Glossy glass in a pebble-like mosaic.
*** Price IS per Sheet ***
- Material: Marble and Glass
- Sheet Size: 12" x 12"
- Thickness: 3/8"
- Finish: Honed finish
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- MARBLE PEBBLES MOSAICS HEART SHAPE - CALACATTA GOLD HONED
- Calacatta Gold Honed Calacatta and Thassos Marble in heart shape pieces
- Material: Marble
- Sheet Size: 12"x12"
- Thickness: 3/8"
- Colors: Gold, White and Grey
- Finish:Honed finish
Can install the residential shower when sealed.
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Measuring: Measure coverage area, make sure to purchase at least 10% extra material than is required. This will account for any breakage or mis-cuts during installation, and ensure you have extra material should you have to replace any tile elements in the future.
- Upon delivery, open and inspect each box of tile.
- Verify dye lot consistency in the following manner. To establish color control samples, randomly select 5 pieces from your order from different boxes.
- To assure shade variations are acceptable check, the remaining sheets or field tile in your order against the control samples, prior to installation.
- If ordering additional materials. Sample shall be sent to help attempt to match previously ordered material.
- Setting Material: Because of the translucent nature of glass, the color of the bonding material will impact the ultimate look of the tile. We highly recommend the use of white polymer modified white thin-set.
Acceptable Thin-Sets (White Color):
- MAPEI: Adesilex P10 Bright White Thin-Set Mortar mixed With Keraply Mortar Additive
- BOSTIK: Glass-Mate GLASS TILE MORTAR
- BOSTIK: ReFlex Ultra-Premium Latex Modified Thin-Set Mortar
- LATICRETE: Glass Tile Adhesive
- TEC SPECIALTY PRODUCTS: Super Flex Premium Performance Universal Latex-Modified ThinSet Mortar
Acceptable Grout:
- MAPEI: Keracolor S
- Bostik: Dimensions and TruColor
- LATICRETE: 1500 Sanded Grout
- TEC: AccuColor Premium Sanded Tile Grout
- Cutting: Plan the placement of the tiles on your wall prior to installation. If you need to cut a mosaic sheet, cut from the back using a utility knife between tiles along the grout joints. Should you need to cut across tiles in a fashion that is not possible with a utility knife, use a wet saw with a diamond blade to cut through the tile.
Applying Setting Materials:
Apply setting material using the notched side of a V-notched trowel. Using the flat side of the trowels, smooth out all ridges to achieve a consistent, even 1/8" (3mm) coverage.Apply glass mosaic sheets, mesh -side down, firmly into freshly laid setting material. Mix and match from assorted sell units to achieve consistent variation. Using a rubber grout float gently press the tile into adhesive to ensure complete contact.
Natural Stone should be sealed prior to grouting. A premium penetrating sealer is recommended for a natural look. Please refer to sealer manufacturer's recommendations for application instructions.
7. Cleaning: Clean all excess grout immediately with a damp sponge. After 12 hours polish off any remaining haze with a dry cloth or towel. For tough stains, we require the use of PH Neutral cleaner to clean the tile and grout, such as Grout and Tile neutral cleaner.
Maintenance and Care
Required to use a soft bristle brush to scrub the tile surfaces and grout. Take care to only use a soft bristle brush, to avoid the chance of scratching or damaging the grout. Then, simply wipe the surface, rinse well with clean water, and dry with a soft clean towel.
We strongly recommend customers to use a licensed tile contractor to do the tile installation and always use TCNA tile installation handbook as the installation guidance
Colors may vary from picture, Product may have chips, pitting and other characteristics, Pictures are only an indication of color, texture and finish
- Carrara White Marble Honed Large Basketweave Mosaic Tile w/ Blue-Gray Dots
- Product Attributes
Item:
- Premium Quality Italian Carrara White Marble HONED LARGE BASKETWEAVE MOSAIC TILE w/ BLUE-GRAY DOTS (ON-MESH)
Dimensions (per piece):
- 1-7/8" (W) X 3-7/8" (L) (Bricks) 7/8" (W) X 7/8" (L) (Dots) X 3/8" (Thickness)
Material:
- Premium Italian Carrara White Marble
Coverage:
- 1 Sheet = 1 Sq. Ft. - Price Per Sheet
Application Area(s):
Commercial and Residential (Interior & Exterior), Indoor, Outdoor, Shower, Countertop, Backsplash, Bathroom, Kitchen, Deck & Patio, Decorative, Floor, Wall, Ceiling, Powder RoomMinimum Purchase:
- 10 sq. ft.
Surface Finish:
- Honed (Flawless, smooth matte finish)
Edge Finish:
- Honed Straight cut/Rectified
- Available Quantity
- All items are normally in stock in large quantities.
- Shipping Details / Cost
- Shipping is available within the 48 continental US States.
- SHIPPING IS FREE ON ALL ORDERS OF THIS ITEM, UNLESS STATED OTHERWISE.
- Special arrangements may be made for international buyers.
- For large orders and all other shipping related inquiries, please contact our shipping department.
- Ship / Lead Time
- All items are in stock. Normally ships within 1-2 Business days
- Item Location: Southern California (Anaheim, CA)
- Local Pickup: Available with appointment.
- Material Origin: ITALY
- Manufacturer / Importer: OTS
- Please keep in mind that each piece of natural stone has unique features that vary it from the others in terms of color, texture and homogeneity. Expect to have some variation between individual pieces when ordering in large quantities.
- Installation of the product requires sealing products and these need to be purchased seperately. (Only the item described in the listing will be shipped out).
Size:
- 1.65 x 1.65 inch pieces mounted on 11.30 x 9.72 (0.76 sq. ft.) sturdy mesh tile sheet
- 4 rows and 6 columns with 72 stones per sheet
- 1/16 inch grout width;
- Thickness: 5/16 inch;
- Finish: Honed (Matte);
- Premium Grade Carrara White Marble Princess Weave Rope Mosaic Tiles w/ Nero Marquina Black. Italian Carrara Venato Bianco Carrera White Marble Honed Princess Weave Rope Mosaic Wall and Floor Tiles are perfect for any interior projects. The Carrara White Marble Princess Weave Rope Mosaic tiles can be used for a kitchen backsplash, bathroom flooring, shower surround, dining room, entryway, spa. Our timeless Matte White Carrera Marble Princess Weave Rope Mosaic tiles with a large selection of coordinating products is available and include arabesque, fish scale, penny round, herringbone, basketweave mosaics, 12x12, 18x18, 12x26, subway tiles, moldings, borders, and more.
A mix of glass and marble mosaic in pebble shaped pieces.
*** PRICE IS PER SHEET ***
- Material: Marble and Glass
- Sheet Size: 12" x 12"
- Thickness: 3/8"
- Colors: Green, Gray and White
- Finish: Honed finish
A mix of Carrara marble and Glossy glass in a pebble-like mosaic.
*** Price IS per Sheet ***
- Material: Marble and Glass
- Sheet Size: 12" x 12"
- Thickness: 3/8"
- Finish: Honed finish
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Aphrodite Mix Grey 12x12 - Mix of Italian Bardiglio Light and dark Grey Marble in heart shape mosaic.
- Suggested Grout Color: Bostik Trucolor White H152
- ** PRICE PER SHEET ***
- Material: Stone
- Sheet Size: 12" x 12"
- Piece Size: Random
- Finish: Honed
- Backing: Mesh
- Leaves mosaics on mesh backing. Create features or cut down to use as borders.
- Suitable for floor, walls, kitchen splash back, wet areas, exterior frost-free zones etc.
- Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Note: All glass, foil backed glass, stainless steel and copper metal, aluminum, resin metal and blended element products must be set a minimum of 8”away from any naked flame.
Setting Materials & Methods:
- Setting material requirements will vary dependent upon the type of mosaic product being installed and the nature of the substrate.
- Advice on the appropriate setting materials should be sought from your tile and stone dealer at the time of purchase.
- Only use setting materials that meet or exceed TCNA guidelines
- Only use an accredited licensed contractor experienced in the art of installing mosaic products.
- Setting methods must conform to the TCNA guidelines.
- Always cut the Victoria Metals with finished side down. During the cutting process, feed the aluminum product through the blade at an extremely slow speed to avoid grabbing.
- Do not cover/protect the Victoria Metals with adhesive tape of any kind.
Note: Grout Selection:
The use of sanded and some premixed urethane micro glass bead enhanced grouts may cause damage to scratch sensitive surfaces. Always check with your Stone and Tile Dealer, Setting Contractor or Grout Manufacturer before selecting the grout type. FlooringSupplyShop.com is not responsible for any damage to the tile surface due to incorrect grout selection or incorrect grouting procedures.Recommended Substrates:
- Sealing prior to grouting is recommended for all stone mosaics.
- Glass (see note below), Stainless Steel, Antique Copper and Aluminum mosaics do not require sealing.
- Note: Pre sealing prior to setting is necessary when installing Barossa Valley Crystal Glass.
- Note: Only use water based sealers with Sydney Harbor Metals.
- Be sure to order enough tile for your entire job. Over-estimating the square footage on a project will allow for unusual shapes, miscalculations and broken tiles on the job. Recommends manufacturer a minimum of 10% wastage allowance
- Using an enhancing sealer will darken the color of these stones!
- We recommend sealing with a penetrating sealer prior to installation.
- Oriental White Honed Marble Mini Versailles Pattern Mosaic Tile
- Design Type: Mosaic Tiles
- Type: Honed Finish
- Design: Mosaic Tiles
- Color: White
- Material Type:Marble
- We sell by: sheet
- Width: 12 Height: 12 Thickness:0.375
- Chip Size (If available)
- Application: Bathroom, Bedroom, Kitchen indoor, and outdoor tiles.
- Product Code:Fancy_group_557
- Product Code: Fancy_group_557
- Sold By Unit: Box
- Coverage Area: 10 FT (square-feet)
- Number of Pieces included in 1 Quantity: 10
- Code: Fancyoption_4005
A mix of Carrara marble and Glossy glass in a pebble-like mosaic.
*** Price IS per Sheet ***
- Material: Marble and Glass
- Sheet Size: 12" x 12"
- Thickness: 3/8"
- Finish: Honed finish
Installation Instructions
Recommended Substrates:
- Properly cured mortar beds-ANSI A108.1B (cured a minimum of 7 days).
- Cementitious backer units (CBU)-ANSI A118.9.
- Concrete slabs cured for 28 days minimum.
- Gypsum board (dry areas only)-ASTM C1396 or ASTM C1396M-04.
- Note: An ANSI A108A-2.1.8 membrane is required behind all CBU installations in wet areas.
- Oriental White / Asian Statuary Marble Honed Large Basketweave Mosaic Tile w/ Blue Gray Dots
- Product Attributes
Item:
- Premium Quality Oriental White / Asian Statuary Marble HONED LARGE BASKET WEAVE MOSAIC TILE w / BLUE GRAY DOTS (ON-MESH)
Dimensions (per piece):
- Sizes (per sheet): 11-3/4" (W) X 11-3/4" (L) X 3/8" (Thickness),
- Sizes (per chip): 1-7/8" (W) X 3-7/8" (L) (Bricks), 7/8" (W) X 7/8" (L) (Dots)
Material:
- Premium Oriental White / Asian Statuary Marble
Coverage:
- 1 Sheet = 0.96 Sq. Ft. - Price per Sheet
Application Area(s):
- Commercial and Residential (Interior & Exterior), Shower, Backsplash, Countertop, Deck & Patio, Decorative, Floor, Wall
Minimum Purchase:
- 10 sq. ft.
Surface Finish:
- HONED ( matte finish)
Edge Finish:
- Straight cut
- Available Quantity
- All items are normally in stock in large quantities.
- Shipping Details / Cost
- Shipping is available within the 48 continental US States.
- SHIPPING IS FREE ON ALL ORDERS OF THIS ITEM, UNLESS STATED OTHERWISE.
- Special arrangements may be made for international buyers.
- For large orders and all other shipping related inquiries, please contact our shipping department.
- Ship / Lead Time
- All items are in stock. Normally ships within 1-2 Business days
- Item Location: Southern California (Anaheim, CA)
- Local Pickup
- Available with appointment.
- Material Origin: PRC
- Manufacturer / Importer: OTS
- Please keep in mind that each piece of natural stone has unique features that vary it from the others in terms of color, texture and homogeneity. Expect to have some variation between individual pieces when ordering in large quantities.
- Installation of the product requires sealing products and these need to be purchased seperately. (Only the item described in the listing will be shipped out).
- //
- Buy Carrara White Marble Honed Large Basketweave Mosaic Tile w/ Black Dots Sample
Item:
- Premium (SELECT) Quality Italian Carrara White Marble
- HONED LARGE BASKET WEAVE MOSAIC TILE w/ BLACK DOTS (ON-MESH)
Dimensions (per piece):
- 1-7/8" (W) X 3-7/8" (L) (Bricks) 7/8" (W) X 7/8" (L) (Dots) X 3/8" (Thickness)
Material:
- Premium Italian Carrara White Marble
Coverage:
- 1 Sheet = 0.96 Sq. Ft.
Application Area(s):
- Commercial and Residential (Interior & Exterior), Shower, Backsplash, Countertop, Deck & Patio, Decorative, Floor, Wall
Minimum Purchase:
- 10 sq. ft.
Surface Finish:
- Honed (Flawless, smooth matte finish)
Edge Finish:
- Honed Straight cut/Rectified
- SAMPLE SIZE = 6'' X 6''
- FREE SHIPPING APPLIES TO ALL ORDERS
- 1 SAMPLE ALLOWED PER HOUSEHOLD / ADDRESS
- MULTIPLE SAMPLES CAN ONLY BE PURCHASED BY DIRECTLY CONTACTING US
- All items are normally in stock in large quantities.
Shipping Details / Cost
- Shipping is available within the 48 continental US States.
- SHIPPING IS FREE ON ALL ORDERS OF THIS ITEM, UNLESS STATED OTHERWISE.
- Special arrangements may be made for international buyers.
- For large orders and all other shipping related inquiries, please contact our shipping department.
All items are in stock. Normally ships within 1-2 Business days
Item Location
Southern California (Anaheim, CA)
Local Pickup
Available with appointment.
Material Origin
ITALY
Manufacturer / Importer
OTS
- Please keep in mind that each piece of natural stone has unique features that vary it from the others in terms of color, texture and homogeneity. Expect to have some variation between individual pieces when ordering in large quantities.
- Installation of the product requires sealing products and these need to be purchased seperately. (Only the item described in the listing will be shipped out).
- Title: White Oak 3D Hon " L" Panel 6X18", Honed, Marble, Ledgers
- Size: 6x18, SQFT per piece: 0.75, Height: 1.25, Length: 6, Width: 18
- Sku: NewMSPearl Drop_143
- Material: MARBLE
- Category: LEDGERS
- Calacatta Gold Marble Honed Mini Versailles Mosaic Tile
- Product Attributes
Item:
- Premium Quality Italian Calacatta Gold Marble
- HONED MINI VERSAILLES MOSAIC TILE (ON-MESH)
Dimensions (Sheet Size):
- 11 3/4" (Width) X 11 3/4" (Length) X 3/8" (Thickness / Depth) - (ALL NOMINAL SIZES)
Material:
- Premium Italian Calacatta Gold Marble
Coverage:
- 1 sheet = 0.96 sq. ft. - Price per Sheets
Application Area(s):
- Commercial and Residential (Interior & Exterior), Shower, Backsplash, Countertop, Deck & Patio, Decorative, Floor, Wall
Minimum Purchase:
- 10 sq. ft.
Surface Finish:
- HONED (Flawless, smooth matte finish)
Edge Finish:
- Straight cut/Rectified
- Available Quantity
- All items are normally in stock in large quantities.
- Shipping Details / Cost
- Shipping is available within the 48 continental US States.
- SHIPPING IS FREE ON ALL ORDERS OF THIS ITEM, UNLESS STATED OTHERWISE.
- Special arrangements may be made for international buyers.
- For large orders and all other shipping related inquiries, please contact our shipping department.
- Ship / Lead Time
- All items are in stock. Normally ships within 1-2 Business days
- Item Location: Southern California (Anaheim, CA)
- Local Pickup: Available with appointment.
- Material Origin: ITALY
- Manufacturer / Importer: OTS
- Please keep in mind that each piece of natural stone has unique features that vary it from the others in terms of color, texture and homogeneity. Expect to have some variation between individual pieces when ordering in large quantities.
- Installation of the product requires sealing products and these need to be purchased seperately. (Only the item described in the listing will be shipped out).
- Bianco Carrara Honed Marble Large Basketweave Mosaic Tile (w/ Blue-Gray Dots)
- Design Type: Honed Finish
- Type: Honed Finish
- Design: Mosaic Tiles
- Color: White
- Material Type:Marble
- We sell by: sheet
- Width: 12 Height: 12 Thickness:0.375
- Chip Size (If available)
- Application: Bathroom, Bedroom, Kitchen indoor, and outdoor tiles.
- Product Code:Fancy_group_392
- Product Code: Fancy_group_392
- Sold By Unit: Box
- Coverage Area: 10 FT (square-feet)
- Number of Pieces included in 1 Quantity: 10
- Code: Fancyoption_3840