Software
Houzz Logo Print
loliz

Microwave trim kit won't fit, but is it even necessary?

11 years ago
I just got a Kitchenaid 24" Convection Microwave (Model #KCMC1575BSS) that I was planning on installing into my island with a trim kit. I got the 30" trim kit which is much too large. The 27" trim kit would probably fit length wise, but it is still too tall. It is 19 1/8" tall and the height of my opening is just 16" with a margin of 1.5" above and 1" below.
Any thoughts? Are trim kits really even necessary? I am most concerned about fire hazards and ventilation more than anything since this is an oven/microwave.

Comments (19)

  • PRO
    11 years ago
    Call Micro-Trim, Inc. I have used them many times with good results. I actually like some of their kits better than the appliance manufacturers kits. They can make a micro trim kit to fit the exact size you need it to be. Great prices too!

    http://www.microtrim.com/microwaves.htm
    loliz thanked Wyland Interior Design Center
  • 11 years ago
    Wow! Thanks so much for the response Wyland! My cabinet is finished and is under the island countertop. I was hoping someone would say that I could trim the kit down. That's good news. Is that difficult to do? What do the edges look like after you have cut that kit? I could hide the top edge under the counter top but the bottom edge would be exposed so it would need to look finished.
    I also looked at the micro trim site you recommended and sent them an email.
  • PRO
    11 years ago
    I highly recommend reading the appliance manual. It will describe exactly how to do it. The trim kits typically overlap the opening on the outside of the cabinet. * See photo below.
  • PRO
    11 years ago
    I would also contact the appliance manufacturer and ask to speak to a technician. They will be able to walk you through it.

    I have had about three of my kitchen projects where my contractors have been able to trim them down. However, my contractors are pretty talented, think out of the box and can make almost anything work.
    loliz thanked Wyland Interior Design Center
  • 11 years ago
    Well I just looked at the manual. Nothing there about how to cut down. Called Kitchenaid. They weren't very helpful either. Actually said they would NOT cut it. So I will just wait to see what micro trim comes up with.
  • PRO
    11 years ago
    last modified: 11 years ago
    Some can , some can't. Typically, when you order cabinet with micowave to have a built-in look, the specs will call out the exact size of the opening and size of cabinet needed. Under the circumstances, I would return the Kitchenaid trim kit and get a refund. Then call Micro-Trim, Inc. They can make one for you the exact size you need it or have the microwave sit in the opening.
    loliz thanked Wyland Interior Design Center
  • 11 years ago
    That's exactly what I think I'm going to do! I already got in touch with microtrim and they sent me some drawings so I think I'll probably go with them if I do it at all. The place where I pruchsed the trim kit from said they would take it back, no problem. I'm going to just try putting the microwave in the space first and see if the trim kit is even necessary.
  • 11 years ago
    We just had this same microwave installed above our oven. Love the trim kit. It vents out the sides of the grill, so I think it's necessary. We had our installed by the appliance store where we bought the appliances. Love it!
  • 11 years ago
    This is a convection microwave, it is not intended for use below counter. Minimum distance of the cutout for the MW is 36'' above the finished floor. Read the manual. It's only intended for use as a built in in a tall oven stack, at the appropriate 36'' height off of the floor. With only the approved trim kit for that proper ventilation.

    Or it can be set on a kitchen counter. All microwaves have installation requirements for proper ventilation of their electronics and associated heat. You need to understand the specs that yours requires. Placing a MW in a cubby that doesn't give it the proper clearances voids the warranty and increases the chance that it will overheat. Or start a fire.

    Put it on the counter. Or return it for a smaller non convection MW that will have enough clearance for proper ventilation with your existing opening and is rated for under cabinet use.
  • PRO
    11 years ago
    last modified: 11 years ago
    The Kitchenaid microwave specs for your model CLEARLY says you can put in into a cabinet. They would not sell a convection microwave trim kit if you couldn't install it into a base. It is not a fire hazard! Microwaves are designed to go into base cabinets and oven cabinets all of the time. Here is your microwave specs that show all of what I just stated. I design them to go into kitchen designs all of the time. Micro-Trim kits will only make them per the requirements of the microwave mfg. with the recommended ventilation. I use them when you need trim kit wider or taller, or when you need to have it come in a different finish than what the mfg. sell.
    loliz thanked Wyland Interior Design Center
  • PRO
    11 years ago
    The use of an after market trim kit that compromises the needed ventilation for the oven will void the warranty. This produces a lot more heat than a standard MW, as it has actual heating elements like a toaster oven. Here is what the manufacturer requires

    . http://www.kitchenaid.com/digitalassets/KCMC1575BSS/Installation%20Instruction_EN.pdf

    It appears to show that they require it to be 36" off of the floor to be used in a built in manner. It's an easy call to ask them to clarify
    loliz thanked User
  • 11 years ago
    This is from the manual:
    Location Requirements
    The microwave oven may be installed over a built-in oven. If
    installing over a built-in oven, make sure there is a minimum of 3"
    (7.6 cm) between the top of the lower oven cutout and the
    microwave oven cutout floor.
    The microwave oven may also be installed in a cabinet by itself
    (without a built-in oven below). For best usability, we recommend
    a minimum distance of 36" (91.4 cm) from the floor to the cutout
    floor.
    Make sure the surrounding cabinetry has clearance to open and
    close freely. Allow a clearance of at least 1⁹⁄₁₆" (4.0 cm) below the
    cutout floor (3" [7.6 cm] for installation above a built-in oven), and
    a clearance of at least 2" (5.1 cm) above the cutout opening.
  • 11 years ago
    I interpret "for best usability" to mean that it is easier to use if it is at least 36" from the floor to the cutout floor, but not that it is a safety requirement.
  • 11 years ago
    last modified: 11 years ago
    Okay slightly off topic, but Wyland, that picture you have of the green tile is almost JUST LIKE MINE! I was trying to figure out how I had uploaded a picture without intentionally doing it! HA! Then I figured out that it wasn't mine. Funny.
  • PRO
    11 years ago
    last modified: 11 years ago
    Hello again loliz, You are correct, the manual does states, ""for best usability" and I also interpret it to mean the same thing that it is easier to use if it is at least 36" from the floor to the cutout floor, but not that it is a safety requirement. I had confirmed this from a Kitchenaid technician, when working on a project not long, where my client was 4'-11" and needed it to be lower than the 36" high. It was okay to have it lower, it was not a requirement.

    In terms of after-market trim kits, like Micro-Trim, Inc and other trim kit manufacturers, they will ONLY make them *per the specs* of the manufacturer so not to compromises ventilation requirements. If it matches the mfg. specs it still is warranted by the appliance mfg. If you need the trim kit to be wider, taller, or a hair bit smaller or shorter, different finish......as long as they match the specs everything is good.

    I had the opportunity to confirmed this, that you can indeed use these after-market trim kits with many appliance manufacturers in the past. A matter of fact, that is where I actually heard about Micro-Trim was from an appliance manufacturer. These trim kit companies would not stay in business if they weren't warranted.

    One more note loliz, make sure that your cabinet open is 17" min. to 17-1/8" max (not smaller than) x 23-1/8" wide (not smaller than).
    loliz thanked Wyland Interior Design Center
  • PRO
    11 years ago

    TrimKits USA builds a state-of-the-art, industry leading trim kit, bar none! Our quality, features and benefits are unsurpassed. Check out our web site: www.trimkitsusa.com

  • 6 years ago

    I've just gotten some good ideas reading info from Wyland Interior Design Center. My 36 inch wide over-the-range microwave stopped working several years ago. I keep looking on the internet for a new one. No one makes a 36 inch one any more. I even contacted all the appliance manufacturers to find out when one would be available. Got no help from any one. I have a 36 inch cooktop. My kitchen was remodeled in 2008 to accommodate the 36 inch wide microwave. So I don't have too many choices. What I have learned is that I should just buy the 30 inch wide over-the-range microwave and live with it until some manufacturer decides to make the 36 inch again. In the meantime, we'll have something we can use. Hurts my heart that we spent all that money redesigning our kitchen and ended up with a microwave that crashed and cannot be replaced.

  • 6 years ago

    Look at Micro Trim, they make side panels to fill in gaps for over the range microwaves. https://www.microtrim.com/otr-microwave-filler-kits/

    We just replaced a microwave with size issues as well; I'm strongly considering buying a second "backup" micro now and storing it until this one dies so we won't have to jump through the same hoops next time.