Software
Houzz Logo Print
otterhead

Honda GCV 190 Auto Return Choke Problem

19 years ago

So my new mower has a total of three hours time on it. Went to fire it up yesterday and the auto choke wouldn't return to full open on its own.

I set the choke, started the mower and the choke lever started to return half way, and that was it. I had to "help" it to the full open position.

Last night I took the choke mechanism off the mower and played with it. There's no obvious dirt, both little cogged wheels look ok and the springs are all there. Everything moves smoothly, *but* the mechanism wasn't able to move to full open without help from my fingers.

I sprayed some silicone based lubricant on the mechanism, no change. I then washed the whole thing by soaking it with WD-40 and gave it a try. Improvement was marginal.

I reinstalled the mechanism on the engine and gave it a try. Opened the choke fully and squeezed the deadman lever. The choke lever started its return trip, slow and lazy and then stopped 1/4 of the way through it's total travel. Gave it a little bump with my finger and it very slowly and lazily returned to full open.

Small engine guru's....any ideas?

As my lawn is being grown from seed and coming in patchy, mowing conditions are pretty dusty, and I assumed that dust/dirt would be gumming up the works. But when I removed the engine cowl, everything underneath was clean. And I used a good amount of WD-40 to try to clean out the "gears" on the choke actutor. There was no obvious dirt or grit to be found there either.

I stopped short of trying to take the gears apart, that looked like it would be a one way trip.

Comments (8)

  • 19 years ago

    Take the mower back and get another one.
    Take it in and get it fixed under warranty.
    Keep using it (without lube) and hope it breaks in and starts working.

    Those are the choices I see for you. BTW, if you exchange it or take it in for repair, don't mention your having worked on it. The Honda auto-choke has been a problem area, so I'm sure there's a factory fix for it.

  • 19 years ago

    I guess it's going back to costco in exchange for a new one. Saxman, you mention the auto choke being a problem area. When I had the mechanism in my hand and was inspecting it, I thought that it was a neat idea, but the execution of it seems to be more complicated than it needs to be.

    I *could* live with helping it out, but A) I paid for an auto choke that's supposed to work and B) the choke and pull cord are on opposite sides and I could see this really starting to piss me off over time.

    Is the maintenance that I did about all one can do to make the darn thing work?

  • 19 years ago

    As of yet I don't recall seeing any "fixes" released from Honda. Don't know how much problem they really are. The few we have seen needed no more then what you already have done.

    These auto-chokes were added for use only on non Honda mowers sold at Box stores. Either they are not selling many or they haven't been all that much of a problem.

    This aftrnoon I'll double check the service bulletins just in case I missed it or discounted it due to seeing so few problems.

  • 19 years ago

    otterhead,
    Now that you "freed" it up some, have you checked it with the engine running? Airflow should help "pull" it open.

  • 19 years ago

    bill_kapaun,

    Had the engine running and still had a lazy return. So off to Costco I went and got my money back. The more I thought about it, the more I knew that the auto return would become a maintenance hassle over time. If I had swapped out for a new one at Costco, the potential for the same problem was there. I really didn't feel like dealing with the prospect of having to give the choke return a helping hand when it was on the side opposite the recoil start.

    Plus, there was a comment made in another post that MTD's with Honda engines were cheapo mowers with the engine as a gimmick.

    So I went shopping and settled on a lawn boy 10684C (C=Canada) for ONLY 12 bucks more than the MTD from costco.

    What a difference! Rear drive LB vs Front Wheel Drive MTD, can't even compare the two. The LB just digs in and goes. Control cables have guides, not zip ties and everything else is more robust. So I gave up stainless, but now have a deck that doesn't flex. There's huge value with the LB.

    I wasn't looking forward to hear the Tecumseh run compared to the Honda, but I guess that I had been brainwashed. The LB is just as quiet as the Honda powered MTD.

    So I am both happy and sad with the LB purchase. The last time an LB was parked at my residence, I 10 and my dad had picked up a used LB that had an under deck exhaust, and sounded like a very quiet outboard when it ran.

  • 19 years ago

    Excellent trade! The 10684 is my favorite mower right now. Yes, no more 2-cycles but still an innovative mower.

  • 18 years ago

    I had a similar problem with a Honda GCV160 engine on a Troy-Bilt mower: the auto choke opened too soon, causing the engine to stall when first started.
    To slow down the movement of the auto choke, I removed the choke lever mechanism (very easy) and used a straightedge and soldering iron to melt several shallow notches in the cam that the choke control arm slides on. It works well now: it takes much longer for the choke to open.
    I decided to do this rather than just return the mower because once it's warmed up, it's one awesome mower.

  • 10 years ago

    In 2013 I purchased a Troy Bilt ,Honda powered walk behind mower. It replaced a 17 year old Briggs and Stratton powered walk behind. I mow almost 1/2 acre about once a week. In the slightly over three years of using the Honda I have had much more maintenance than I expected.. I have worked as a mechanic for over forty years. I do not see a great deal of superior engineering used in this application of Honda engine. The Honda performs well but not noticeably better than the older L-head Briggs and Stratton . The Honda is much more affected by dust and dirt and needs tuned up religiously. Recently I have noticed some mild smoking under some conditions which concerns me considering the mower is less than four years into its life. So I will have to wait and see if it will really give me the useful life that the previous mower did and make no mistake I change oil and air cleaners and spark plugs regularly. Plus I have already had to replace the coil on the Honda. My impression is that the best of Honda engineering goes to motorcycles and automobiles and the name is the main contribution to small engines.