Software
Houzz Logo Print
jteekell

Honda Mower Problem-Backfire thru Carb?

19 years ago

I have a Honda walk behind that has been awsome until recently. I get it started and get into the grass and after a couple minutes when encountering thicker stuff it will bog a bit and backfire through the carb, blowing the air cleaner off sometimes. I've looked at everything I can think of. Checked for a sheared flywheel key, replaced the carb (due to screwing it up cleaning it) and cleaned the tank. I would think it was either a fuel or timing thing but I am at a loss at this point. Any thoughts?

Comments (33)

  • 19 years ago

    Possible a sticking valve....

  • 19 years ago

    When you cleaned the tank did you actually drain it completely?
    Symptoms sound somewhat like water in the fuel.
    Otherwise, it kind of sounds like the ignition coil is going $outh.

  • 19 years ago

    Sounds like the cam drive is breaking down or the intake valve is sticking. Put a couple ounces of Marvel Mystery Oil in the oil and see if it frees the valve. If the cam pulley is wearing out at the center hole and losing timing, you're toast unless it's still under warranty. Always use STA-BIL in your gas can every time you fill it.

  • 19 years ago

    Thank you for all of the responses. Answering some questions. I removed the tank and drained completely, sprayed down the screen from top and back flushed with break parts cleaner. Pretty sure its clean! Removed the muffler and it is free flowing and see no buildup in the exhaust port. I was actually thinking about the coil since it starts to happen after a few minutes of running and I know some coil problems dont show until it heats up some. I didn't want to prejudice your creative juices in my first post though. I will try throwing another part at the problem - the coil. Probably put some oil additive in just to see - cant hurt right (i hope). Dont want to think about problems with the cam pully!

  • 19 years ago

    check for a sheared key on the blade end of the shaft.

  • 19 years ago

    Rub a little Aloe oil on the handle grip, and it should clear up in a few minutes...............................

    If not, post the model numbers, so we know what you have.
    When checking the flywheel key, how did you do it?
    And how did you tighten it back up.
    Is it OHV or OHC?

    Let us know......

    Fish

  • 19 years ago

    Try closing the armature air gap to .008". This seems to work on GCV engines that start to act up when hot.

  • 18 years ago

    Hello, HELP I have the same problem with my Honda mower! jteekell did find out what the problem was

  • 15 years ago

    I have a similar problem except my mower won't start at all.The first time I tried it this year, I gave 1 pull& it fired & ran for about 5 seconds & puffed out alittle smoke' & that was it. Every time I tried after that it backfires thru the carb. Any help would be greatly appreciated...

  • 15 years ago

    My problem is the same, my mower will not start at all and backfires thru the carb as well.

  • 11 years ago

    I have a problem with mine she is backfiring from the carb as well

  • 11 years ago

    Damn! Its an epidemic! I suspect some sticking valves after winter storage. Put the previously recommended MMO or Seafoam in the oil and gas. Mowers love it. If its something the mild solvent can handle, it will get better with use. Otherwise you have a mechanical problem.

  • 11 years ago

    Change the spark plug, I had the same problem, same symptoms a new spark plug was all it took to get it running again. Ben

  • 11 years ago

    the only thing marvel mystery oil is good at is parting fools from their money. there is no mystery, it's baby oil, perfume and some coloring. It won't hurt anything, but it doesn't help anything. It's snake oil for gullible gear heads.

    replace the air filter. dirty filters make the engine run too rich. too rich leaves carbon deposits on the plug, and everywhere in the combustion chamber. under high load, like heavy patch of grass that pulls the rpms down combustion chamber temperatures shoot up and make the carbon deposits glow red. the next time the engine goes into intake stroke the glowing carbon ignites the fuel/air mixture before the exhaust valve closes.

    bang.

  • 11 years ago

    But you see, the 'snake oil' is good for that condition by helping to prevent the build-up in the first place.

  • 11 years ago
    last modified: 11 years ago

    No, I don't see because it does no such thing. NTSB tested it and found it to be 74 percent mineral oil, 25 percent stoddard solvent, and 1 percent lard. Or more exactly, Mineral Oil Mineral Spirits, lard and o-Dichlorobenzene to make it smell like it does.

    if baby oil prevented carbon build up it would already be used in engine oil or some additive that would stand up to testing scrutiny.

    Think about how an engine works. There are already additives in fuel that lubricate the upper part of the cylinder. We also know that fuel alone, especially if it's to rich, can leave carbon deposits behind. (note modern fuel injection and computer controls make cut way down on too rich situations) Mystery Oil is completely organic. Burning organics leave behind carbon. (yes, fuel is organic to but remember, lean and hot leaves very little behind) It would seem impossible for MMO to leave nothing behind so the notion of it having cleaning properties seems especially dubious, and certainly not supported by any data.


    NTSB analyzed it because someone had put way to much in the fuel tank of a small airplane whose engine fouled and choked out at full throttle just aver takeoff. Yes, the cause was TOO much but it was too much as in too much baby oil in the gasoline. They did a detailed analysis just as the do in all crashes where they suspect something in the fuel might be the cause. What that analysis showed was there is no mystery in mystery oil. all claims about it's benefits are anecdotal and can not be supported by ANY documentation that can withstand the slightest scrutiny. Your neighbor says it works because he puts it in and has no problems, even though there is no evidence he would have had any problems if he hadn't used it. You use it because he did and say it works because of confirmation bias, then someone else has to have some because you do... and we're off the the races.

    It literally works the same way old time snake oil sold from horse drawn wagons works. A product that does no harm sold by a good salesman with a loud commanding voice used by people that say it works because he said so.

    Literally, snake oil for gearheads.

    And please, I don't want hear antidotes or testimonials. They are the weakest of all forms of evidence. If you have data I'd love to see it, but I won't be holding my breath because I know there is none. I've done the homework. I'd find the NTSB report but I've learned that unless your curious and have an open skeptical mind and look it up yourself, me showing it to you won't matter. Mystery Oil users are true believers, and I don't mean that in a good way. True believers, like religious fanatics say "Evidence? We don't need no stinking evidence!". It's like they are confused by the term. And I understand why. Form the time we get up until we go back to sleep someone is marketing to us. We can't even sit on hold on the telephone without someone forcing us to hear a commercial. And it gets louder and more insistent all the time. And they market appealing to emotion, not data. You get so accustomed to it you totally forget that people should have to prove what they say, not just say it and have it believed. So you get sold by mystery oil, and worse yet, you become the salesman using the same bullshit pitch to everyone you can so you look smart because you put "mystery" oil in your oil, gas (who knows, maybe you put it in your coffee) as though you have knowledge of some secret when in fact the only mystery is why you believe it does anything.

  • 10 years ago
    last modified: 10 years ago

    My Honda mower was doing the exact same thing as the OP. It would run fine for a few minutes and then under load would lose power and backfire through the carb, blowing the air filter and cover off. Replacing the spark plug fixed it.

    On on a side note, this has been a great mower. Bought it new in spring of 2003, and this was the first spark plug replacement in 13 years. Estimated to have about 400 hours on it right now. It has ALWAYS started on the first pull, even the first start after sitting all winter. Only bad part is I'd like to get a new one with adjustable walking pace (mine's a single speed) but this thing just keeps going!

  • 10 years ago
    last modified: 10 years ago

    Denny: Could be a multitude of things , least you applied the KISS Protocol . If not Plug or Wire than Timing , Coil , Valve Issues or last but not least Pre-ignition as carbon crank advised. Preventative Mtce and Common Sense and Stoddard Solvent goes a long Way !

  • 10 years ago

    It's not the kind of pre-ignition like a ping or spark knock. Those happen when the valves are closed. I'd say in this case carbon on the old plug was glowing and igniting the mixture before the valve gets a chance to close. The only things that can ignite the backfire have to do with glowing carbon. Even if the mixture is ridiculously rich something has to set it off. Something is setting it off before the plug does. The ignition has to be happening in the cylinder or intake manifold, and mowers don't have much of an intake manifold. Backfire by definition is a blast outward from the cylinder through the carburetor. If the plug was black with carbon that tells you what the inside of the cylinder looks like. Still, a dirty air filter will make it run rich because of course not enough air can get through it. The amount of fuel delivered by the carb is determined solely by the amount of vacuum created by the piston going down in the cylinder but the amount of air can be less than designed because it can't get past the dirty filter. Same amount of fuel, less air = rich mixture. Rich mixture = incomplete burn. Incomplete burn means carbon left behind. Make sure the filter is clean if it's cleanable or replace it if it's not. The add something like Seafoam to the gas to loosen the carbon in the cylinder head.

    For engine combustion you need fuel/air mix, compression and something to ignite it. I said it that way because you want that something to be the spark plug but it's not always the case.

    Sooner or later a plug will get stuff built up on it especially if you mow heavy grass that pulls the rpms down even at full throttle. Again, full throttle is set on most all mowers now so if the revs come down it can't draw as much air even though the amount of fuel entering will be the same. The mixture gets richer. Again, less air in the combustion chamber, same amount of fuel = rich condition. The burn is incomplete and whats left gets stuck on the inside. Usually if you run it enough at full revs it will clear out the mess, but over time carbon will happen.

    Replacing the plug can make it run without solving any possible underlying reasons for carbon build up on the plug.


    But hell, it's a farm implement really. They're not made to run as clean as a race car engine.

  • 10 years ago
    last modified: 10 years ago

    There was a decent amount of carbon build up on the base of the plug, so it's true that the hot, glowing carbon may have been pre-igniting the mixture.

    I have to respectfully disagree with you though regarding a dirty air filter causing a rich mixture. The low pressure in the carb Venturi is what causes the fuel to be drawn through the carb jets. If there's less air moving though the carb due to a restriction, then less fuel will also be drawn up.

  • 10 years ago
    last modified: 10 years ago

    Carboncrank: No I'am referring to Pre-ignition normally caused by glowing carbon on the plug or within the combustion camber , which normally occurs prior to the plug timing sequence BTDC. Opposed to Detonation a similar but different phenomenom caused by combination of extended heat and pressure which occurs after the plug timing sequence ATDC . As I said previously to Denny , numerous scenerios could produce the symtoms the OP described . I have found that with a little common sense and working knowledge you can eliminate the lesser evil and hopefully at a lesser overall cost. Each individual case has it indicators , thus the KISS Protocol lol .

  • 10 years ago
    last modified: 10 years ago

    dennyd75

    Hi Denny,

    Another way to look at it.

    unrestricted airflow + vacuum drawn by the piston moving down = desired vacuum at the carb and desired amount of fuel drawn from the carb.

    Partially restricted air intake + vacuum drawn from the piston moving down = higher than desired vacuum at the carb which = more fuel drawn out with less air able to get in = rich mixture.

    You rightly say low pressure at the carb is what draws fuel out. What you don't see is if intake is restricted you will have lower pressure at the carb, IE higher vacuum. Lie you say, vacuum draws out the fuel. More vacuum more fuel. More fuel less air = rich. It's not the air flowing by that draws fuel out, it's the vacuum sucking it out.

    A manual choke works by reducing the air flow right? It draws fuel with less air and make the mix richer. Had you thought of that? If you leave a manual choke on what happens? As it gets up to operating temperature It will sputter and black smoke comes out the exhaust and it eventually stall. If you were take the plug out right then you'd find it blackened and wet with fuel. The engine gives up trying to clear the overly rich mixture out of the head, the plug gets wet and it won't fire and it stalls out. Actually, you find motors with a clogged air filter will start without the choke.

    So running and engine with a dirty air filter is the same as leaving the choke partially on.
    Trust me, it it gets dirty enough it will quit running and if that
    happens you're going to find a blackened and possibly wet plug.

    If you completely block air to the carb and spin the engine over it will flood. In fact I've done that on cars long ago where the choke didn't work, it was cold out and it wouldn't start. Simply take a shop rag and hold it over the carb and spin it over at take the rag off soon as it fires, put it partially back on if it tries to stall and do this enough to get some cylinder head temperature (it is a two person job). Restricting the air enriched the mixture to achieve the cold start.

    If you keep going in heavy grass and the mower stalls what do you think is happening? It floods the engine. It's what makes them harder to restart. Too much fuel in a warm engine. You would also notice as the revs come down at full throttle you'd see black exhaust. Black smoke is always too rich. Rich conditions in a warmed up engine make carbon rich exhaust.

    The first thing that should be done on finding evidence of too rich conditions is check the air filter. Same is true on cars or any 4 stoke engine. On a mower if you have a clean air filter and have cleaned or replaced the plug, made sure it's the right plug and right temperature range plug, and the fuel isn't too old and it still is too rich about all you have left is the carburetor.

    That's assuming you don't have a blown or leaking head gasket which leaves evidence where the head and block meet. and that's a too rich problem but for a different reason. If the head gasket is leaking it won't build enough compression to raise mixture temperatures to where they need to be to burn cleanly.

    If the air filter is clean you can take the carb off and apart and there are things you can easily check that can make it flow too much fuel like, I think, float valves but I'm not a carb expert.

  • 10 years ago

    sstracker1 "No I'am (sic) referring to Pre-ignition normally caused by glowing carbon on the plug or within the combustion camber (sic)"

    I don't understand "no". That's exactly what I said.

  • 10 years ago
    last modified: 10 years ago

    Cranky ; Not trying to split hairs , yes "no ping or carbon knock involved" , I'am in agreement with your potential for a glowing ember (carbon based) causing ignition of fuel within the cylinder prior to the spark plug firing sequence (BTDC) . In the Automotive Field Field it is referred to as Pre-ignition in severe cases , with Valves closed or still partially open , Not Rocket Science Bro , is there another Synonym you would prefer ? In either case it was not established in this Op's situation or Denny's for that matter , nor was a dirty air filter , although it may be suggested since Denny has advised that his spark plug was over 13 yrs old . Most prudent individuals clean or replace air filters when warranted depending on air quality conditions. However , dirty air filter is not the only situation for backfiring lean fuel mixture under load will also . As I said numerous items to consider lol . Anyhow Good discussion , I believe we are on the same page ! P.S. What are your background credentials , former Diesel Mechanic and 3rd Class Stationary Engineer here , have not seen your username on this Forum previously ?

  • 10 years ago

    Great rebuttal Crank, and makes perfect sense. Thanks!

  • 10 years ago

    Alls Well That Ends Well !

  • 10 years ago

    I've never been a fan of that school of thought. The more you understand about the last problem the less hair you may pull out on the next one.

  • 10 years ago
    last modified: 10 years ago

    In this scenario it applies since nothing has been adequately Confirmed as the Actual Causation . Perhaps more plausible as Contributing Causation of a Engine Backfire Situation , in this 13 yr old engine of Dennys with suspect mtce scheduling . In your theoretical explaination the engine , would have experienced extreme visual blackish smoking well before any accumulation of carbon on or within the combustion chamber , which in Dennys case would have been obvious . I would suspect rather a old spark plug perhaps with carbon fouling and even bridged causing it to over heat over time , and breakdown internally causing less then optimium flame kernel and incomplete combustion and thus a rich fuel charge . This would cause the same eventual backfire condition. Hell , Old Dino Oil breaking down over a 13 yr period also would cause a carbon fouled combustion chamber due to blow by from carbon fouled or simple tired rings , which would eventually have potential for the same symtoms , even with a New Air Filter ! Only supposition and conjecture on your part Cranky , Nothing Definite ! lol

  • 9 years ago

    I have the Honda gx340 and was having a back firing through the carb problem. after reading this thread and trying a loose gas cap cleaning carb replacing air filter checking the plug for blue spark and proper gap also cleaning tank everything seemed to be ok. still same problem. after giving up for the day decided to go and buy a new plug and sure enough runs like new so just goes to show just because you think its blue its not .lol problem solved thank you everyone for your comments

  • 8 years ago

    I have the answer my mower would run for 15 minutes and then blow the air cleaner off I used Lucas upper engine lubricant and injector cleaner at a ratio much higher than recommended 2 oz to a half a tank of gas on the mower probably a quart I had to restart it several times but eventually it ran smooth my guess is the valve seals have failed allowing oil to travel up the valve through the valve guide and carbonize allowing the intake valve not to close all the way this product removes that carbon and lubricates I disabled the safety equipment on my mower it ran until it was out of fuel eventually hopefully this is a help

  • 8 years ago
    last modified: 8 years ago

    Lucas is a good cleaner via solvency along with a added lubricity agent . Does a great job on carb cleaning and cleaning of injectors also . Long term it will reduce valve train carbon deposits . Much better product then some other snake oil additives indeed .

  • last year

    I agree on MMO, my Izzy has backfired today

Sponsored
Peabody Landscape Group
Average rating: 3.5 out of 5 stars8 Reviews
Columbus' Reliable Landscape Design & Contracting