Software
Houzz Logo Print
greg123_gw

Kohler 12.5 engine not starting

19 years ago

I am at a loss. Mowed the yard for the second time this season. Previously would start on full choke. This time didn't start so moved to idle position and it started. (assumed flooded carb.) When done, turned off. Hour later went to put in shed and wouldn't start. Removed carb. Looked O.K. Reassembled and put gas in carb. Gas is not being pulled into engine. Got good spark. No extra smoke, oil good. Anybody have any ideas?

Comments (27)

  • 19 years ago

    Might have sticking/ stuck valve-s. If you can, do a compression check, with spark plug removed, and thumb over spark plug hole. Or, use a compression guage if you have access to one.
    Those small engines have a penchant for doing just what yours did. they sit all winter, stored away, seemingly forgotten by the person who depended on them all summer! So, for spite, they start right up, you think you are the luckiest guy in the world, and that engine decides to show you that you ain't so smart after all! So, they quit at the most inopportune time, and awaaay we go! Muttering, and wondering what to do next! And now you know just what you have to do----Tune it up, with a new spark plug, clean the carb, new gasoline, change the oil, and, if yer lucky it'll start,and run!

  • 19 years ago

    A compression test isn't very useful on an engine with an ACR (automatic compression release), like this engine. A leak down test is much more useful and can pinpoint the source of low compression. It is possible that the intake valve is stuck open. Starting without choke would lead me to believe that the inlet needle and seat in the carburetor isn't sealing, allowing fuel to puddle in the intake. You did use fuel stabilizer while the engine sat for the off season correct?

  • 19 years ago

    I have a similar problem - STX38 with the Kohler 12.5 - Sat for 2 years with battery and gas removed - New plug, gas, oil and filer and it cranks fine, but won't fire - I have spark and gas seems to be getting to the carb but nothing, not even a sputter - Was wonding if a valve is stuck? I see the 5 bolts holding the valve cover but wanted some guidance on what if anything I should be prepared for - Any parts I should have around or things to watch out for? Any assistance appreciated - Bob

  • 19 years ago

    Remove the air filter and prime the carb with a couple teaspoons worth of gas.
    IF it will run for a few seconds, then we have eliminated spark and stuck valves and narrowed it down to fuel.

  • 19 years ago

    Bill,

    Well, I spoon fed some fresh gas into the carb and still ziltch - Turns over fine, but no fire - Tried it several times and nothing - I tested (maybe incorrectly) for spark with a timing light and I see if firing off in a regular pattern as the engine turns but I guess I can't see how hot. The plug is brand new but tried it with the old just in case with same result - Visual inspection of the old plug FYI is text book 'normal'. Up for any suggestions...
    Thanks, Bob

  • 19 years ago

    I would repeat the "prime with gas test" up to 3-4 times.
    Which model engine is this? Command?

  • 19 years ago

    Thanks again for the reply and happy fathers day... I just got back from a trip and tried this again today at least 6 or 7 times - (I'm starting to worry about the starter as it's seen more use in the last few weeks then in the last 8 years!)- I've put this test through the ringer and still nothing even approaching a sputter. The oil, gas, fuel and oil filetrs are new (removed the air filter for this test) as is the plug with the proper gap - I have an old timing light which connects up to the battery and inline between the coil and plug and it flashes when the engine turns so I assume I'm getting spark - The battery is at peak charge - I'll try any suggestions at this point - I really like my dealer but he will charge me a ton $$ if he needs to work on this - I'd like to exahust anything I can possibly do on my own even if I need to learn some new skills. Thanks again, Bob

  • 19 years ago

    Yes, forgot to mention it is the Command OHV 12.5 HP in a Deere STX38 - Bob

  • 19 years ago

    Can you smell gas after a lot of cranking? After 2 years I would suspect the carb. Clogged jets or sticking float. If you smell a lot of gas, then I would suspect the float. If not a clog. In any event a carb rebuild may be in order.

  • 19 years ago

    I'd pull the valve cover and make sure both valves are moving. Maybe one stuck open during storage??
    You MIGHT need a new gasket.

  • 19 years ago

    Another thing to consider is the connection on the wire to the plug. Might sound silly, but I have found that after sitting around a while, the connector on the end of the wire gets bad, even with it protected by the rubber boot. I had this problem with a STX 38 that I just got that had sat for three years. Plug looked good, but the connection was bad up in the boot. Just something to check out.

  • 19 years ago

    Perhaps someone out there can help me with the same engine. JD STX-38, 19 years old. New carb AND coil within the past 30 days, but same problem of unreliability. It starts immediately, and often runs for an hour or more, then sputters, and finally stops. When cranked, it will start, but will sputter and die repeatedly. After sitting for a half-hour or so, it will re-start most times. I thought that a new coil would solve the problem, and the machine ran like a new one for the first time or two that I used it, and then, same game under the porch! Does ANYBODY OUT THERE IN TRACTORLAND have the answer for me? Thanks! Phil

    p.s. It does indeed have a non-Kohler fuel filter on it, a Briggs and Stratton, but I fail to understand how THAT could be the root cause of my problem if the mower will sometimes run for two or three cutting before it acts up !

  • 19 years ago

    pwerntz,

    I just replaced the coil (or ignition module) in my 15 yr old Kohler Magnum MV-20 which was experiencing the same symptoms as you describe. It would crank when cold but then sputter and die within a few minutes. The coil replacement appears to have fixed the problem but one poster told me to be sure to check for "stray voltage from the kill wire circuit". According to fisher40037 a full 12 volt leak into the kill circuit will damage a new coil very quickly. My mechanic agrees this could occur but says he checked mine out good and apparently the coil just went bad over time. (BTW, I also have a non-Kohler fuel filter and it has never been a problem).

  • 19 years ago

    "p.s. It does indeed have a non-Kohler fuel filter on it, a Briggs and Stratton, but I fail to understand how THAT could be the root cause of my problem if the mower will sometimes run for two or three cutting before it acts up !"

    Who said it was the cause of YOUR problem?
    The OP's problem is that it doesn't start up NOW! Not every 2-3 mowings!

  • 19 years ago

    Thanks to everyone for the assistance on this - The good news is that my mower is working 100% - The bad new is I'm not sure why - I had been working on gas / valve issues and avoiding the issue of spark because I had my old timing light connected up and it was firing (wired between the ignition module and the plug) so I assumed all was good - I did notice however when I pulled the plug out and connected it to the plug cable that there never was any spark at the plug tip the way I would expect when cranking the engine - I kept cranking away and moving the plug wire, trying to ground the spark plug case and all of a sudden it was like the 4th of July all over again and the plug was firing. I put the plug back in the engine, and it started almost instantly - Mowed the lawn, let it sit for 3 hours, fired right back up so now I'm dumbfounded - I have been yanking and pulling on cables and wires for the last month and have probably had this plug in and out of the engine 5 or more times - With and withouty the timing light connected - I'm sure I would have noticed the arc if it was being shorted someplace up the line - Does anyone have any ideas or should I just be thankful? I would prefer not to have to do this again later in the year - Hope everyone had a great 4th - Bob

  • 19 years ago

    I have a similar problem and found this forum while searching for answers. I have a JD LT133 with a Kohler Command 13hp. My problem is the engine will not start on choke. I can move the throttle to idle, and it will spit and sputter and sometimes backfire. After some time of trying, the engine will seem to "catch" and run fine. Then again sometimes it will flood. This started happening after running low on fuel. A coinsidence? I have replaced the plug and fule filter, but that has not made a difference. Any help or suggestions would be appreciated.

  • 17 years ago

    Posting for a friend. His mower starts fine then it will run for about 30 minutes and then shuts down. If he tries to restart it sputters like it's going to start but doesn't. When the unitis cooled down about 20 minutes he can restart it and then gets about 30 - 30 minutes more out of it. He has replaced the coil but hasn't yet corrected the problem. He can't seem to get any advice locally so I offered to see if I could find something on the internet for him. Any suggestions as to where he would look for a problem would be a great help. Thanks.

  • 15 years ago

    well i have an john deere stx 38 hydro 13 hp kohler command i have trouble with starting and keeping it running, will idle to high or not high enough,,well i got brave and took engine off tractor, took inside shop, removed pan, and found something out that very moment, and now i understand clearly 100%, i also talked to john deere mech.tec. after a kohler command type engine gets alot of hours on it, cam with go out and take gov. gear with it, although sometimes only gov. gearwill go out, and it that case you are very lucky. i like my little stx hydro i will prob look for used engine mabe a briggs if i could make it fit????would love to hear ideas for engine replacement.

  • 15 years ago

    I have a john deere stx38 with the 12.5 kohler comand. Its been a good motor but now it won't start. Its got good spark. Its getting gas to the carb. The carb was clean , but it won't crank. I've noticed when it starts it needs to click to run good. What is that click? May be the intake valve is stuck or bent. Any ideas?

  • 10 years ago

    I recently found with my kohler 12.5 command and no cranking but would just click, it was the little black box in rear of of tractor by battery on left side. The wires in and out are red. It has two 90 degree black rubber boots connected to it and the terminals in them were rusted and broken I also replaced the relay, found on amazon, cost about $19.95 Now starts awesome. There is also a fuse under the black plastic cover by the ignition switch that blows, and a fuseable Linc that burns out on the red wire on black relay box on right side rear back by battery, check fuesable Linc on both sides of a little diode that is in line no power on one side..it's bad and replace!

    But now I am struggling with the engine dying after 30 minutes of running. And mine has fresh tune up, with filters, and oil change and filter. I will figure it out and keep every one posted. Mike



  • 10 years ago

    Mike, a new thread may be helpful along with what machine your engine is on. It could be as simple as a non venting fuel cap or an improper fuel filter.

  • 10 years ago

    Ok, I have the Sears 17.0 HP, 6 speed lawn tractor with the Kohler engine, model CV 490 type 27505. I am experiencing the same issue, engine will not start. Last season the mower ran up to the end of the season, then quit. I have done all of the same tests and checked the compression. 90 psi when cranking, have gas to carb and spark. I have an in line spark tester and it is showing a spark, uncertain of the actual degree of spark. The mower quit at the end of last season. What does the Regulator/rectifier do or control and could this cause the problem? Thanks and ant help would be appreciated as I am ready to junk the mower. Greg

  • 10 years ago

    get can of rattlecan carb cleaner from autoparts store. Remove engine carb air cleaner. With help from assistant, crank engine normally while spraying one or two shot of carb cleaner directly in to throat of carb.

    If engine pops or tries to start, you have a fuel delivery problem, most likely within the carb. Repair as necessary.

    If no pop, spark or mechanical. You say you have spark - s/b a bright blue/white.

    If so, ck crankshaft key for being partially sheared (search this forum for how-to's)

    post back with gory details if still trouble.

  • 10 years ago

    Well, I already removed the bowl of the carb, ran a welding wire up through the jet and blew carb cleaner under air pressure through the carb, rebuilt the carb last season, replaced the electronic solenoid on the bowl. Have not checked the key but will try it this weekend. Until next time, keep on pushing the trim mower! Thank you, Greg

  • 10 years ago

    still don't know if you have a fuel , spark or mech prob....on carb cleaning, need fresh rebuild kit for that carb, disasm-soak overnite in liquid cleaner to loosen crap; probe every orifice/passageway with a small dia stiff brass wire while using magnifier; blowing all out with compressed air; rebuild using only fresh valve/seats/gaskets from kit...

    if you do pull flywheel, do reasm to correct torque ( info on kohler engine website).

  • 4 years ago

    I have a 12 hp Koehler in my Ingersoll 222. Had the same issue with hard starting and running fine for a while, then it would spit and sputter until it quit. After replacing many unnecessary parts, I put a new fuel pump on it and that solved all the stalling and sputtering issues. Runs great now. I think the fuel pump was about $18.00. Hope this helps.

Sponsored