Software
Houzz Logo Print
aces26

Sump wont go back on

16 years ago

I have a briggs 460777-2276-e1 motor. I needed to change the sump gasket and shaft oil seal. I've done it several times on other motors but I had a new problem with this one. When i went to reinstall the sump case back on the motor, it will not go completely closed. Upon closer inspection I can see the timing gear is about 1/16th higher than the surface of the motor. For the sump cover to rest flat on the motor I know that this timing gear must rest lower than the surface of the mating surfaces of the motor. The timing gear is resting flat on the crank and is on the keyway properly and cannot possibly go down the crankshaft any farther but is still to high. Is it possible that when I pulled the sump cover that somehow the crankshaft RAISED 1/16th to 1/8th an inch? If so, how do I get it to go back down. I've tried about everything except a BFH. LOL. I just cant seem to get this back closed and I know the problem is the sump case hitting the timing gear. Please help.

Comments (7)

  • 16 years ago

    I assume you mean the timing gear on the crankshaft. You may have it on upside down. The tapered, recessed, side of the gear goes in, side that is out is flat.

    Walt Conner

  • 16 years ago

    Yes, I mean the timing gear on the crankshaft. I never took it off until I ran into the problem. There is no need for what I was doing, but no, the timing gear is not upside down, the tapered side of the timing gear is down, or in facing the first lobe of the crank, timing mark on the timing gear is on the top or out facing me. Please, any more suggestions?

  • 16 years ago

    If you have your engine resting on the flywheel, then yes, the crankshaft will move. The timing gear on the crankshaft against the bearing bore in the oil sump is what limits the end play of the crankshaft. Take the weight off the flywheel/crankshaft and see if things aren't OK then.

    Walt Conner

  • 16 years ago

    You were right, it was resting on the flywheel. I went at with a fresh mind the next day and found that very problem. I had the motor resting on some 2x4's and it had shifted on me and I didnt catch it earlier. Talk about feeling stupid! Sometimes I guess you have to step away and come back to it. I just got it in the tractor and now I have other problems I am sorting through. First I found the fuel line between the filter and carb had multiple holes in it. I THINK the portion from the filter to the tank is still fine. Then found lots of water in the tank, but cleaned that out. I then found the 3 screw fuel pump wasnt drawing any fuel. Upon inspection found it had been worked on and put together wrong. They had the large spring and ring protector on the wrong side of the diaghram. Switched it around and I now have a LITTLE draw through the fuel line, it fills the fuel filter but it still doesnt appear to be getting it to the carb. May have to rebuild. Doesnt really look like it needs it but kinda at a loss at this point. What I find more troubling is the fact that I have fire at both plugs, but in a hour of trying all I have gotten is one pop from the motor when trying to start. Not even a sputter while spaying starting fluid while cranking. Feel 99% sure I didnt move the cam gear when I had the motor open to throw off the timing but starting to wonder. Not sure about the timing marks though. Timing gear on the crank is easy to understand, only one mark. But the cam gear has four marks, like markings on a map legend N, S, E, W. Which would it be lining up with? Never had to retime one of these before. Keep the suggestions coming, you've been ontrack so far!

  • 16 years ago

    "Not sure about the timing marks though. Timing gear on the crank is easy to understand, only one mark. But the cam gear has four marks, like markings on a map legend N, S, E, W. Which would it be lining up with? "

    I once rebuilt these engine as a sort of specialty and have never seen what you are talking about. Markings have always been obvious.

    You might want to go to http://www.thepowerportal.com/Login.htm at Login put voed_schools for password put briggs browse around and you should find a Service Manual for your engine that you can download.

    Your scenario does not add up, something is missing, didn't knock the key out of the crankshaft when you were fooling around with the timing gear?

    Walt Conner

  • 16 years ago

    Tried sveral ways to get this motor fired today. Still not even a sputter. Dont understand why when I have good fire at the plugs. Gonna pull it again tomorrow and see about checking the timing. I'll post what I find. If the timing marks look bizarre like I remember I may try and post photos.

  • 16 years ago

    Did you check the hole that the camshaft gear fits into. Its possible something has fallen in there and it keeps the cam gear raised a bit! Stranger things have happened. Also some old fashioned heavy wheel bearing grease will keep things in place when reassembling. I made a tool from a strip of cardboard, shaped like this:
    _____________\/
    Turn the strip over, to visualize how it looks. Stick it between the case and the gear, and slip the gear case cover down until the cam gear goes into its hole, then gently pull the strip out. Its hard to print it on the computer, but it'll give ya an idea. I used the back page of a pencil tablet. That kind of cardboard.

Sponsored
Custom Home Works
Average rating: 4.6 out of 5 stars10 Reviews
Franklin County's Award-Winning Design, Build and Remodeling Expert