Software
Houzz Logo Print
rbig

how difficult is this 'do it yourself repair'?

19 years ago

Got a Kawasaki FC540V engine on a JD GT-275. It's a strong runner,

but I'm getting a little smoke continuously. Awhile back it was

smoking only briefly on startup.

Assuming I'm going to have to put new rings in, what all does this

entail? I'm guessing we'll probably have to pull the engine to get to

the pan to get the bearing caps off the rod so I can get the piston

out. Is this correct?

Anyting else I should check before deciding on rings?

In the meantime, we're just feeding it oil and mowing happily away.

Comments (14)

  • 19 years ago

    I would first clean out the gunk and carbon out of the engine first, i.e add Seafoam to the gas. Make sure the engine is totally clean first before tearing down the engine.

  • 19 years ago

    Since you are willing to "tear into" the engine, one must assume that you are satisfied with the machine otherwise (as you implied) and plan to hold onto it a while. In light of that I would suggest you first arm yourself with the factory service manual that covers your engine. That way you will have all the OEM specs, torque specs and procedures. I am a firm believer in getting the facts first whenever possible. To me that means getting a shop manual unless you have a buddy working at the dealer (or shop) that can get all the data for you. Now you just "stand by", there should be a few more posts to your thread with some additional suggestions from other forum members.

  • 19 years ago

    Pull the head and look at the piston/cyl. You will likely find a bad head gasket.

    Fish

  • 19 years ago

    Please elaborate.

  • 19 years ago

    WHOC, go to www.seafoamsales.com then select "MOTOR TREATMENT" then pick "gas engines". I have never used this product so I don't have any testimony to give here (you can't believe that, huh?). The blurb on the product declares it to be the end all & do all but I don't know personally. Sounds good though.

  • 19 years ago

    I agree with mownie. Go to a used book store or online and find a service & repair manual. Some OEM manuals just don't give your enoght info to do a complete rebuild, because that is what you will be doing. You will need to get an rebuild kit for your make and model and size. Do a search for used repair manuals for your engine.

  • 19 years ago

    Seafoam is an engine cleaner. I have used Seafoam for a few years with good results with cars and with small engines. You mix it with the fuel and also pour a little into the carb (or for an automobile, into intake vacuum hose). It cleans the carburetor and valves and can free up sticking piston rings. You can also mix some with the engine oil soon before an oil change and it acts as an engine flush. You can buy it at Pep Boys or NAPA auto parts I think it is $6.99 a pint. It burns the carbon deposit and gunk out of your engine.

    Here is my "testimonial" for the product I have used it on a Subaru with 135,000 miles on it (that I bought with 108,000 on it), the car ran but a little rough, the Seafoam in the intake cleaned it right up. It creates billowing white smoke out the tailpipe that is as big as your house when you first start it, let it idle for a couple minutes, then you drive it for like 10 miles and the smoke disappears. The only thing is if the engine is filthy figure on changing your spark plug later because as it burns the crud out of the engine it may foul the plug.

    I bought a 20 year old MTD trimmer-edger with a 3 HP Briggs for $50 last fall that ran but ran rough and idled poorly and smoked some, decided to use it over the weekend for the first time, I just mixed Seafoam into the gas can and ran the edger ... the thing starts right up and idles and runs smooth now and does not smoke. Then I changed the air filter and spark plug after the engine cleaning. You would hardly know it was the same engine, the engine idles smoothly now and runs quieter. I did not have to put it directly into the carb I just mixed it with the gas.

    I cannot say if it will fix your engine smoking condition but it is seems worth a try for $7 before you start to tear down the whole engine. It would be a shame to tear it down and replace the piston rings if the rings or valve was just sticking and Seafoam treatment would have fixed it. Just cleaning the engine thoroughly might fix your problem, but even if you still need to repair it after it is clean, you are starting from a clean engine.

  • 19 years ago

    Fair enough kubotbx. I will try some in our 1968 Snapper Comet 30. It must have 5,000 or 6,000 hours on it (or possibly more as for a while it cut for 2 families each week). It smokes a little (really just a little) and has the hint of oil smell in the exhaust. It is likely that all this is truly due to genuine wear but hey, it couldn't hurt to experiment I guess.

  • 19 years ago

    For sure I'll try SeaFoam before turning a wrench. It's great stuff.

    If it finally comes to wrench turning, I was hoping I could get by with just pulling the piston and putting new rings on. However, mention is made of needed an engine overhaul kit. This is much more involved than I was thinking. Will it be necessary to do a complete overhaul just to stop oil burning, if SeaFoam doesn't do it?

  • 19 years ago

    rbig, I suggest doing a systematic troubleshoot before tearing it apart and throwing parts at it. First clean the engine as thoroughly as possible and start it. Are there any obvious oil leaks? A leaking crankcase gasket will cause loss of vacuum. Do a compression test with the throttle wide open. It should be at least 65psi. What fisher said, that is a common problem.

  • 19 years ago

    canguy, a leaking crankcase gasket is bad in and of itself because of the oil leak. Please elaborate on how a leaking crankcase gasket can cause a loss of vacuum in a 4 cycle engine.

  • 19 years ago

    Someone please explain how "a leaking crankcase gasket will cause loss of vacuum." In a 4 cycle engine?

  • 19 years ago

    Forget the miracle products, pull the head, clean off
    the built up carbon, you will see the condition of the
    cylinder, and also likely find a small blown out portion
    of gasket material from the cumbustion chamber to the
    pushrod gallery, which sends compression to the crankcase
    and forces oil mist into the air breather, thus burning
    the oil.

    Fish

  • 19 years ago

    You had me thinking on that one, fisher. Caught me off guard.

Sponsored