Software
Houzz Logo Print
rayucho

Husqvarna tractor quits while mowing

18 years ago

During mowing my engine often stumbles and begins to quit. Sometimes I can get it to resume operation by holding down the brake pedal as the engine emits a lot of smoke but gradually comes up to full speed with no more smoke. It seems that something is cutting off the ignition temporarily. When the engine does quit it is easily restarted as if nothing happened. I checked the seat safety switch and it seems to operate as it should. Are there any other safety switches that could cause this problem and where are they located?

My Husqvarna model is YTH1542XP and is four years old.

Thanks for any help that you can provide.

Comments (11)

  • 18 years ago

    IF you don't have a schematic, go here-
    http://www.oscar-wilson.com/MANUALS/HUSQVARNA/HAU15H42E.PDF

    Assuming it's a safety switch problem-

    You can temporarily bypass the seat switch with a simple jumper on the connector and see if that "cures" the problem.
    Another potential trouble spot is the OPR, aka Operator Presence Relay. IF it is losing 12V to terminal 85, terminal 87A will ground the ignition (through the clutch switch)and kills the engine. (The configuration shown in the schematic is 12V NOT applied to 85.
    Check to make sure the OPR connector is tight and pins clean.
    It's a Bosch Relay that looks like this-
    {{gwi:328174}}

    You might check the connection to the carb fuel solenoid also I don't think it's that, but......
    IF still stymied, check the connection on the back of the ignition switch. This may sound strange, butt does it make a difference if the head lights are on? That could indicate intermittence in the ign. switch or its connector.

  • 18 years ago

    Bill Kapaun,

    Thanks for your clear and logical suggestions. I will follow each lead and report results.

    Ray

  • 18 years ago

    have you noticed it doing this while having the mower in an incline of any type. For example when the mower is going downhill - it is most likely to do this ?

    If so you might have water in your carb bowl / gas tank.

    good luck.

  • 18 years ago

    Bill Kapaun,

    I've studied the electrical schematic that you referred me to and found that it is different than the schematic shown in the Owner's Manual that came with my tractor even though the model number is the same in both schematics. I found a major difference when I disconnected the seat safety switch and installed a jumper across the female connector. When the engine would not start with the jumper installed I realized that the jumper was grounding the ignition. That is because the seat switch on my tractor opens the ignition grounding circuit when the seat is occupied. So by simply unplugging this switch it becomes disabled and the engine starts OK. However the circuit in your referenced schematic works just the opposite and a jumper is needed to disable the switch as you suggested.

    Another major difference is that my schematic shows no Operator Presence Relay and the parts listing does not contain a relay.

    In any case, tomorrow, if the rain stops, I'll try the tractor with the seat switch disconnected to see if that solves the intermittent quitting problem.

    I can email you the electrical schematic from my manual if I knew where to send it. Thanks again for your helpful suggestions.

    Ray

  • 18 years ago

    OK, I'll look for a newer version-
    I think that was from a 2003?
    The grounding connector probably came a bit later,since it was so easy to bypass.
    You'll need to use something to hold the grounding tab from making contact to bypass.
    Kudos for noticing!

    How's this one look?
    http://www.oscar-wilson.com/MANUALS/HUSQVARNA/HAU15H42F.PDF

  • 18 years ago

    I'm going to assume this is a correct schematic.

    The problem pretty much has to be the seat switch or PTO switch.
    Pushing in the clutch pedal removes those from grounding the circuit.

    I know some Sears tractors (same manf) had the seat switch mounted so that it barely engaged. Some people added a wooded shim? to get more plunger engagement.
    Else, maybe the PTO switch knob is "creeping" a bit. Try applying pressure to the ON position and see if it makes a difference.

  • 18 years ago

    Bill Kapaun,

    Yes, your most recent manual exactly matches my electrical schematic. Today I mowed the lawn with the seat switch disconnected but continued to experience engine ignition cut-outs. In every case I was able to prevent engine quits by depressing the brake pedal. Tomorrow I will simulate mowing but with the PTO disengaged and mower not turning. If I encounter no cut-outs, the problem may be in that switch as you suggest. If so, perhaps spraying the switch with electronic circuit cleaner might fix this problem. Will keep you posted.

    Ray

  • 18 years ago

    I assume you "disabled" the grounding connector to the seat switch. Else it shouldn't run with the PTO engaged, unless you had the pedal pushed in.

    If that's the case-
    that pretty much means it's the PTO switch.
    The M terminal (Magneto) is grounded to G (Ground)to kill the spark.
    Key OFF, M+G+A1
    The PTO & Seat switches also ground that wire. Pushing in the pedal upens that circuit.

    The only other alternative I could think of, is if you had a bad connection to the fuel solenoid and pushing the pedal moved that wire to regain contact. Unlikely though!

    BTW, if you need a new PTO switch, take the PN of the switch and Google AYP and the PN. You'll find the same switch under a lot of different brands. That'll allow you to price shop.

  • 18 years ago

    Bill Kapaun,

    Bill, You are correct; my intermittent engine problem is caused by the PTO switch. The engine quits only when the mower is engaged by the PTO switch and I can restore engine operation by disengaging this switch as well as by depressing the brake pedal. Will search for a new switch as you suggested.

    Thanks for the perceptive help, Ray

  • 18 years ago

    Glad you narrowed it down!
    We like to hear the success stories!

  • 5 years ago

    I know this post is 13 years old but I have the same problem. But I bypassed my pto switch with toggle switch. But in the same place in the yard every time it stumbles and dies. plz help if you can. Direct to me is regina.pm2148@gmail.com

Sponsored
Peabody Landscape Group
Average rating: 3.5 out of 5 stars8 Reviews
Columbus' Reliable Landscape Design & Contracting