Software
Houzz Logo Print
alicia7b

best method for building stone walkway

19 years ago

Has anyone here build a stone walkway? If so I need your help.

DH built a stone sidewalk that has stone set in sand. Everything is held in place by bricks on each side. The bricks have been dug into the clay and placed on end. The problem is that the stones slide around in the sand and tip on end to creating tripping hazards. Does he need to take out all of the sand, use it to mix the mortar and just put mortar in? That seems like the logical solution. What are your suggestions?

Comments (9)

  • 19 years ago

    Alicia,

    It sounds like the sand base underneath the stones was not compacted enough. Remove the stones and use a tamp to pack the sand until it is firm and level. make sure the sand is damp so that it will pack. A basic set of instructions is at the link below. Good luck!

    Here is a link that might be useful: Laying a Flagstone Walk

  • 19 years ago

    Thanks farmsteward!

  • 19 years ago

    we made one, but our stones were irregular, not smooth flat flagstone. w e didn't lay them in sand, instead roughed up the clay a bit and kept flipping them up and back down until we got them so they were level and not tippy- hard when often the underside was a bit bowed or pointed. but, with the clay, as it compacts down, it does make a really nice solid walkway. ours was on a slope, too- which i really don't think sand would work too well for. the only stones that became problems were ones that were too small and light and so they didn't ever 'sit' into the clay right. we reworked some til they worked, and others got swapped out. the first portion was done 10 + years ago, and the second about 4 years ago. both have been very stable. we did install a drain and gravel under the second portion, because it was at the bottom of the slope where it floods and next to the pond. once in a while, i have to go through and poke through the dirt to the gravel so the water can drain quickly, but that's the only maintenance other than weeding. now my only issue with stability is keeping my kids from upending them searching for worms to feed their turtles! lol.

  • 19 years ago

    If you want to use polymeric sand instead of sand, it will stay put. I just explained this in a thread over on the Cottage Garden forum. It's a DIY project and will only take 1/2 a day as long as you've not had rain for 2 days before and not expecting rain 2 days after.

    The polymeric goes in the joints and we have screenings underneath the flagstone on our patio (that we built). I think our sidwalk (done by the landscaper) may not even have a base as it's very casual.

    Cameron

    Here is a link that might be useful: thread about polymeric sand

  • 19 years ago

    Cameron the polymeric sand sounds great but it looks like the nearest dealer is in Greensboro. Is that where you got yours?

    DH is on vacation and has spent today setting the bricks lining the sidewalk in concrete. This is the sidewalk leading up to the house and is on a bit of a slope, so it's very heavy traffic and needs to be very stable. He stills needs to do something about the stones in the sand. Currently the stones are sitting on about an inch of untamped sand, and we'll need to add more to bring the stones up level with the bricks.

  • 19 years ago

    Alicia --

    I bought our polymeric at the John Deer Landscaping place on Hwy 64 between Apex and Jordan Lake. They do sell to the public. Another web friend went there and they talked her out of it telling her it will crack. Well, mortar cracks too -- however, with polymeric you can reapply it in thin layers very easily years later. Understand that it's for filling the joints and not the base for the stone. Dampened screenings that are tamped down and screed (leveled) work great for the base.

    If you have any questions, just drop me an email from My Page.

    Cameron

  • 19 years ago

    Thanks Cameron. The polymeric sand sounds a lot easier than spreading mortar.

  • 19 years ago

    I can attest to the polymeric sand as well, as I just finished my irregular flagstone patio this afternoon. Thanks to Cameron's assistance/guidance, I got the polymeric sand from John Deere in Apex (Techni-Seal HP for larger joints - you can go to techniseal.com for videos and instructions). The bags weigh 66lbs and are $50.00/bag. I too used landscaping fabric then screenings for the base.
    I asked the people at John Deere Landscaping if they thought the polyeric sand would work for irregular flagstone that had been dry laid, and they told me the joints would be too large for the polymeric sand to maintain its bond. However, after talking with Cameron, I felt a lot more confident about using this product.

    Here's a picture of my patio (if I can get it to work). You can also contact me if you have any questions.

    Good luck!
    Susan

  • 19 years ago

    This should do it...sorry about the pic on the previous post not showing up.

Sponsored
AIS Renovations
Average rating: 4.5 out of 5 stars15 Reviews
Custom Craftsmanship & Construction Solutions in Franklin County, Ohio