Software
Houzz Logo Print
jimdora_gw

Shower re-do/ Niches & Tile

18 years ago

Thanks for a wonderful web site. I have been reading all day and need a little extra help. My husband and I renovating an existing bathroom. We had to totally tear out the shower because it was leaking into the adjoining rooms. It was built in the 50's with no shower pan/liner.

The floor is a concrete slab and we have removed everything back to the wall studs.

First Question: What do I need to do to to water proof the shower walls? We are planning to use Cement backer board and then tile on top. It this OK. Several sites have used Ditra or Kerdi but I am not sure this is really necessary or something I want to tackle.

Second question: Shower floor will have a sloped motar bed and a plastic liner (PVC or CPE). Is this OK?

Third question: I want to put niches in the shower. How do I make sure they are water proof? We would like to build our own nich instead of using the prebuilt ones because of size restrictions and cost.

I know most of these questions have been answered before but I am having trouble finding the correct links. Thanks in advance for any help.

Dora

Comments (8)

  • 18 years ago

    Okay-- If you're going to use a PVC or CPE liner, then the Kerdi is unnecessary. The only thing you would need is a vapor barrier behind the cement board, which would consist of either 6 mil polyethlene, or 15 pound tar paper, the bottom of which would get tucked into the top of the pan liner.

    One other thing-- before that liner goes in (and this is a step even alot of pros miss) you MUST form a mortar slope for UNDER the pan membrane. The reason is that water that gets through the tile, grout, and mortar will get to the liner and if it's not sloped, it'll just sit in the pan, and "ferment". It has the potential to get extremely unhealthy. As long as the liner is sloped, though, water will follow gravity to the weepholes at the base of the drain and exit the shower pan, drastically increasing the life of your shower.

    As for the niches, frame them, and then cement board them as you will the rest of the shower. Once that's done, you can use one of the roll-on or trowel-on membranes available, such as Custom Building Product's Redgard, or Laticrete's fabric reinforced 9235, or Hydroment's Ultraset. You coat the entire niche, as well as 6" out onto the wall in all directions from the niche.

    Piece of cake!! :-)

  • 18 years ago

    Thanks for the response. We had already learned out about the pre-slope but it is nice to have our info confirmed.
    Question: Which liner do you like better? PVC or the CPE

    Question: Can you get the roll-on trowel-on membranes at HD or Lowes or do they have to be special ordered? These two stores are an hours drive away.

    Thank you,
    Dora

  • 18 years ago

    Question: Which liner do you like better? PVC or the CPE

    Either or. The one I usually use is called Chloroloy, which is a CPE membrane made by Noble.

    Question: Can you get the roll-on trowel-on membranes at HD or Lowes or do they have to be special ordered?

    You might want to call ahead to make sure, but HD usually stocks Redgard. Over at Lowes, though, you may have to order the small unit of 9235.

  • 18 years ago

    BIll, I just read this post (I researching waterproofing the niche), but I just read you're advise about the pre-slope in the shower. I know for a fact that the contractors did not do that. they just sloped the pan on top of the liner. Is our shower doomed? Do we ripe it out? and start over again? I think I want to cry again...

  • 18 years ago

    Let me put it this way. If it were my choice, I'd say yes, it should come out and be redone. But it's not my money, either. Many showers, in spite of the fact that there are several places where the spec is read to say the liner needs to be sloped as well as the finished floor, are installed with flat laying liners every day. Will it work for several years? most likely. However, there also seems to be a correlation between flat bottomed shower pans and weepholes clogging up, causing what appears to be water leakage, and although not leakage per se, it causes just as much damage. It's also responsible for holding atleast SOME water in the pan, even when working properly, which promotes all kinds of mold and bacterial growth inside the mortar under your shower floor tile.

    I guess the bottom line is if you'd rather, you can take your chances and roll the dice with respect to how long the shower will last. It could last several years, or it could have problems a year or two down the road. One thing is guaranteed-- it won't last nearly as long as it would had the liner been presloped.

  • 18 years ago

    We are ripping out our shower as well. We were going to leave the bottom and tile over it. Is this okay? How do you know if it is installed correctly?

  • 18 years ago

    Let me ask you this-- how old is your shower?

  • 15 years ago

    Bill, you wrote, "either 6 mil polyethlene, or 15 pound tar paper, the bottom of which would get tucked into the top of the pan liner."

    What do you mean by tucked into? We did our preslope bed and have installed the liner. It was our intention to have both the tar paper and hardiebacker come down in front of the liner so that any moisture is brought into the pan.
    Thanks for your help.