Software
Houzz Logo Print
medha_nanal

Installing floating vanity

17 years ago

Hello all,

I have found a few beautiful and affordable vanities on the internet, however they do not sell the hardware to float those on, in all the cases. Therefore I am wondering if there is a standard way to float the vanity?

It does not look like exact same technique as hanging high kitchen cabinets; because it will bear the weight of a vanity top and a sink, not to mention someone leaning over it. Are they reinforced by underlying brackets etc? In that case, can someone explain to me exact names/specifications of the supporting hardware?

(I am a complete newbie to the hardware lingo thus my question).

Thanks in advance!

Comments (17)

  • 17 years ago

    When we remodeled our bathroom, we took it down to the studs. So we were able to reinforce the studs with cross studs. The vanity did come with underlying brackets but these can be bought at any hardware store.

    You can do the same by just opening up the wall that you want to attach it to. I am by no means a plumber but that also helped us to locate the plumbing as it also had to be somewhat modified for the new vessel sink and top mounted faucet. We raised our vanity higher than usual for comfort.

    I will attach some pics later including the bracket.

  • 17 years ago

    Thank you, dollfanz. I would look forward to your pictures and also more tips/experiences from other posters.

    Our remodel, too, will be done by gutting the entire bathroom, therefore it is possible for us to add more cross-studs. We have been impressing it upon our remodeller that he should put in brackets at the bottom. He has not done this before, but he seems quite a smart guy.

    Also, dollfanz and others who might respond later, please let me know where you got your vanities. I am looking at ebay types.

  • 17 years ago

    See my thread about our 'bling' bathroom.

    The floating vanity I build was from solid bubinga. Weighed a ton, plus the glass countertop plus the marble vessel sink.

    I made the back of the cabinet really strong and then used six 5in lag bolts with large washers to hang the vanity. Used a support while it was being installed. Slowly removed the support to see if it would lean.. no, it didnt :)

    Then we added the glass counter and the sink. It is all holding up well. Also added undercabinet LEDs to pump up the bling :)

    Here is a link that might be useful: floating vanity

  • 17 years ago

    Here are some pictures including the bracket that came with the vanity. We too bought our vanity on Ebay. We were very pleased with the company that sold it to us. It has a glass countertop with glass vessel sink. The pictures are from when we first installed it so there was still some construction going on.
    They are quite heavy. You will need those cross studs, not only for the vanity but for the bracket as well.
    I don't believe the bracket alone would be enough to support it. It does level it quite nicely too.




  • 17 years ago

    we had the "x-large" floating vanity by duravit recently installed. i don't remember it coming with anything but some long screws, and no brackets. it weighed a ton, too. check out their website and look up the specs and technical info on them. it'll probably show what hardware come with it and what perparation to the site is necessary (i don't remember making any myself). good luck.

  • 17 years ago

    Thanks, everyone.

    Pharaoh, I saw your bling bathroom (totally dazzling!) when you posted the pix. At the time the fact that vanity was floating totally escaped me because I was not tuned into floating vanities at that time!

    Anyways, I have some questions:
    - What do you mean by "extra strong back of vanity"? Did you put two sheets or how did you strengthen it?
    - Any experts out here with technical spec/numbers (weight of the vanity with a ceramic sink+top+person leaning, and how much strength can the standard cross stud supports offer etc?) -- DH wants numbers to be convinced :-(

  • 17 years ago

    Homey_bird,
    Thanks, usually vanities have at thin plywood in the back. That will not work. So make sure there are solid wood bracing that you can bolt through.
    I will post a photo of the unfinished vanity on the bling thread for reference.

    cant say much about a person leaning on it :)

  • 17 years ago

    Pharaoh,

    Now that makes me worried because since I am no diy'er and certainly have no carpentry skills, I will have to find someone....

    Did dollfanz and nolamom do the same? What precautions are needed by the contractor for fitting the vanity?

  • 17 years ago

    Homey, I think if the vanity is designed to be floated, I am sure it will have the bracing built in to it. Since I made my own, I was able to build it as I wanted.

    The other solution is to use the brackets are shown in a previous post or put a wood/metal rail and then set the vanity on it. A decent contractor should be able to figure this out :)

  • 17 years ago

    Homey Bird, we did do it ourselves. It really isn't that hard. The cross brace/studs along with the under brace shown above is really enough.
    Pharaoh is right, they are designed to be floated. Use really good anchors plus the brace that will be provided and you should be fine.
    We are about to do another one for a master bath and it will be twice as long as the guest bathroom.

  • 17 years ago

    Dollfanz and pharaoh, thanks a lot for your encouragement. I know I am being a bit paranoid here, but just want to take no risks. DH is already skeptical therefore I will be soley responsible for any mishaps regarding the floating vanity.

    FWIW, I found a vanity that also comes with brackets and all sorts of screws. Found at Decorplanet, an ebay seller. Does anyone else have a good experience with any other seller? (There is another thread running with Modernbathroom.com around here where I posted: overstock.com, danishmodern.com to mention a few others that I know of).

  • 17 years ago

    homey_bird: yes, the contractor renovating my masterbath installed my duravit, with one strong helper. it's really not a diy job, for the sheer weight of the darn thing. imagine balancing this thing and leveling it at the same time. like the old joke about "how many does it take to screw in a"...floating vanity!!! let me know if there's something you'd like me to ask my contractor. he's supposed to be stopping by tomorrow.

  • 17 years ago

    Hi Nolamom,
    Thanks a lot for offering to find the info for me! I have a 55-year old house where we will be gutting the bathroom. My DH is not sure if the existing studs would support a floating vanity and therefore it would be helpful to me to know :

    1. For an old house (studs still look normal 4x6's elsewhere but we have not gutted the bath yet) do we need any special retrofitting? This is 1st level bath in a single story house.
    2. Roughly, how will the studs be placed? We are doing a 24" vanity that we would like to float.
    3. What are the red flags to abandon floating and get legs for the vanity instead? :-)

    Thanks a million for doing this for me!

  • 17 years ago

    got your message too late. but i'm expecting him tomorrow, monday. i'll ask if he placed any special bracing in the wall, while it was open. in the meantime, i really should try to learn to post pics!

  • 17 years ago

    homey_bird:
    while the bathroom was gutted, in anticipation of the vanity, my contractor did place an additional 2x6 for bracing across two studs for added measure. the vanity came with only fours bolts (and washers) about 4-5" in length and four sheetrock anchors. the holes on the back of the vanity are placed 16" apart, so that it could be drilled into two studs, which is preferable. i feel there should be at least one bolt drilled into a stud. four bolts into sheetrock only, even with anchors, seems to precarious for comfort. my duravit washbasin is chunky and runs the whole length of the console. it's much heavier than the streamlined looks of the one dollfanz posted. btw, my contractor looked at the picture of the braces on that one too, and says they provide no added security.

    i will try to post pictures in the next couple of days. good luck.

  • 17 years ago

    Hi Homey Bird,
    i was just wondering - were you pleased with your order from DecorPLanet?
    i just ordered from them and my heart is sort of uneasy about it.....

  • 17 years ago

    Hi Tina,
    Actually, I did not go with Decor Planet finally. My vanity is ordered from a local vanity dealer.

    Sorry about not being much helpful. I hope your experience goes ok. Let us know!