Software
Houzz Logo Print
sturdytree

Wolf blowers and hoods

16 years ago

I live in the UK and am considering buying the 48" dual fuel Wolf range. However, I am also planning to install a (indian style) tandoor oven(!), which is basically a 24" wide box with a large hole in the top to insert kebab skewers etc. It is gas-fired and will be roughly the same height as the range. It will be positioned adjacent to the range, so the two together will be 72" across.

I will need a hood (am thinking of a Wolf Pro Wall Hood to match the stainless steel on the range), and will be grateful for advice on the following:

We can go with a 66" wide hood, but this leaves a 3" deficit each side - not sure how significant a problem that could cause (tandoor's opening will be comfortably within the hood area)

If the deficit could cause a problem, an alternative is to have the 54" hood over the range and a 30" hood over the tandoor, positioned so there is 6" excess on each side (the point where the hoods meet will be over the point where the range/tandoor meet). I think visually this may not look too bad, although we then have the issue of higher cost, 2 lots of ducting and 2 blowers (unless both hoods can be connected to the same external blower?)

Our construction means we cannot have an inline blower, so the choice is internal v remote. A remote blower would have to be placed on the roof as putting it on the wall (there is an external wall next to the range/tandoor) would mean the 10" depth blower will cross our neighbour's boundary line. Does anyone have any pictures of a Wolf remote blower as it would look from the outside? That would really help as I undersand it is quite large and we have strict regulations on this here in the UK. Are the actual dimensions as stated in the manual (25" wide x 29.5" high x 10" depth)? I ask as the Wolf salesman here indicated the depth is 25" too.

Also, the ducting to a roof blower would only be a couple of feet - the Wolf manual warns there may be a 'noise issue' with a short duct and remote blower. Any practical experiences on this?

If we went with an internal blower (1100 cfm), of course still ducted to an external wall plate, what is the noise like?

All comments and advice gratefully received.

Comments (7)

  • 16 years ago

    I just went through deciding on a hood (Wolf 42" wall chimney with 1200cfm and external blower to go with a 36" BS w/ grill), and I did a lot of research (internet and talking with staff but always first qualifying their knowledge to include real experience), so I'll offer a reply:

    First, a tandoor oven, that's fantastic! Not only home-made tikka/kabbobs, but naan and roti, wow.

    From my research, I learned that if one is going to do any high heat cooking (e.g. woking, searing, grilling), having the hood extend over the edges by 3" (or 6" as you mention) isn't a bad idea (even if actual airflow is determined by a combination of variable like capture area (width and depth and location/height), blower size, and angles). But, I think unless you were to never use the "partially-covered" burners in your 66" hood option.

    I like either your two hood option, or consider a different brand of hood that spans the full needed width (or even has slight over-extend).

  • 16 years ago

    Thanks for the response.

    I'm torn between 66" and falling 3" short each side or getting 2 hoods with all the extra headache and cost that involves, but at least having a 3" excess each side!

    I've decided to go for an internal blower (1100 cfm) as the external one sounds like it will look too large on the roof, and maybe just as noisy given the short ducting.

  • 16 years ago

    I have a Wolf 1500 cfm exterior blower (made by Broan-Nutone), but no photo at this time. It only extends about 10 inches above the roof. It blows down along the roof contour. So, in technical 'Merken, one would say the unit was 25 inches transverse to the roof pitch, 29 inches along the roof pitch, and 10 inches perpendicular to the plane of the roof surface. (I'm using your dimensions because I haven't measured mine, but they seem right.) Which dimension one calls high and which one calls deep depends on the roof pitch.

    Anyway, for its size, it is much less protrusive than all the other ports on my roof. (Oven area ventilation downblast fan, house boiler chimney, DWV stacks, and the piece de resistance, the MUA intake "mushroom.") The Wolf fan is a centrifugal type so it can be low in height and still throw a lot of air with a two-foot diameter blade.

    Ventilation at such flow rates requires a source of make-up air (MUA). (Even with electric heat one doesn't want to be pulling air through leaky walls, and with other forms of heat there is danger of pulling chimney gasses into the house.) Open windows work, if the weather is accommodating. Otherwise, you will need a somewhat complicated system for providing filtered air at the desired temperature, or more than typical layers of wool attire.

    With respect to hood size, as previously reported on these pages, there does need to be an overlap beyond the burner area to capture the rising, expanding cooking effluent. Expansion of 45 degrees total cone angle is nominal for conventional cooking processes. I have not seen any measurements for tandoor ovens.

    This fan (at least mine) has a slight rumble that might succumb to dynamic balancing. There is a hiss through the baffles of the Wolf hood. I do have a longish duct and have a Fantech silencer in it so your noise may be higher. With a short duct, at least the duct noise due to turbulence will be low. One has to consider these comments in the light of relative silence, because the noise level is well under conversational, and much less than older hoods I've experienced.

    kas

  • 16 years ago

    Thanks Kas, that was very helpful

    With the 2 hood option, I am a bit worried about the occasions when both will be on - double the noise, although I hear what you say about the improvements in technology to make these things less noisy

  • 16 years ago

    Kas,

    One more thing please - what is the noise level of the remote blower like from the outside? I am thinking of my neighbours who may sit within about 15 feet earshot.

  • 16 years ago

    Well, it doesn't sound like a motor-driven chain rotating against the inside of a steel barrel, if that is your fear. I am rarely close to it when it is running, but my impression is that it is reasonably quiet. A bit of a whoosh sound, I think.

    I expect you will find that most of the time the fan can be running at less than full power, and will be even quieter.

    With your house spacing, exhausted cooking odor may be more of an issue in the local area than brief periods of fan noise that will almost always be quieter than traffic.

    With respect to using two hoods. it is possible above the back-draft dampers to join the ducting to lead to a single exhaust fan. Given that your configuration is against a wall, a 1500 cfm rated fan _may_ be adequate for all that cooking surface. However, my choice would be two fans or a larger fan. Larger forces you to non Wolf supplied equipment and interfacing it with the hood control, if desired, might be a not-recommended action. A separate control might be required mounted elsewhere. Two fans will require less MUA to heat most of the time because each fan has less aperture to deal with and each flow rate can be adjusted for the cooking it is dealing with.

    kas

  • 16 years ago

    Thanks again Kas,

    We've decided to go with the 66" hood and compromise on the 3" deficit each side - I think on the range side this 3" takes you to the edge of the pan rest (so all of the pan is likely to be under the hood). Installing and operating 2 fans just seems too much to cope with.

    We will also be going for an internal 1100cfm motor with venting to a wall plate (I understand the Wolf plate directs the air downwards and not perpendicular to the wall). My neighbours will just have to live with any cooking aromas, just as we have learn to live with theirs.