Software
Houzz Logo Print
happygram_gw

Pot size on induction cooktop...please help!

19 years ago

Hello again,

After searching this website as well as the manuals, I can't find the answer to my question...

Can you use a pot that's larger than the circle of the induction cooktop "burner"? For example, if I have a 11 inch frypan and the largest circle marked on the top is 9 inches, will burner still work???

Thanks in advance for your help. The answer to this is going to be the ultimate decision maker for us about using induction instead of running a gas line.

Comments (9)

  • 19 years ago

    Yes, it will still work however the direct heat will not extend out past the 9" so you will be forced to fry within the 9" in your fry pan unless you're using cast iron which, once pre-heated, will residually retain heat outside of the 9" but still not as hot as within the 9.

    Definitely an important factor in choosing an induction cooktop is burner size.

  • 19 years ago

    Happygram,

    On another posting you said you were looking at the Diva or the Viking 30" cooktop. Have you looked for the Thermador 30" cooktop? It has one large element.

  • 19 years ago

    Yup. Larger is fine, but then I've mainly been using cast iron.

    It's JUST like electric--heat is only applied to the "burner" area, but the heat migrates depending on the composition of the pan.

  • 19 years ago

    For 30" induction cooktops
    Thermador, GE Monogram, GE Profile, Kitchen Aid all look much alike. They have 4 elements and one element is 11". They should all be available soon.

  • 19 years ago

    The 36" dedetriech 309 has a 12" burner in the middle, plus a 9" and 6" on each side.

    So far I've just used a 12" pan in the middle, but hope to find a 14" saute pan soon. If and when I do, I'll report back here how well it works. Somewhere I read that it was OK to use a pan 2" larger than the burner ring.

  • 19 years ago

    I believe manufacturers recommend that the maximum accommodation to be 1" larger diameter than the burner -- so a 10" pan on a 9" burner. You have more localization of heat with induction than you do with gas, because a flame can spread while an induction field is more strictly confined.

    My experience with cast iron is that it heats more evently BUT if you exceed the burner diameter by more than 1" you will still have a significant heat drop-off issue.

  • 19 years ago

    Pan size is also an issue when the pan is not big enough for the large hob, even when the difference between hob size and pan size is quite small, at least on our Thermador hybrid. I don't know about other brands, but the large center hob on the Thermador is actually 2 rings, a small inner ring and the outer ring when large pans are used. The issue we've had is that our unit will not engage the outer ring unless the pan we are using almost exactly fits the entire coverage area of the hob. The result has been that the center hob is good only for very small or very large pans, not very practical for our daily use. The technician believes the sensor for our center hob is overly sensitive and he will either replace the hob or the entire unit because of other issues (very loud clicks and hums), depending on Thermador's response.

  • 19 years ago

    I have the 36" viking induction cooktop, 6 burners. I phoned viking directly to ask about pot size compared to burner size. they told me you could go 2" larger than the burner size.

    I think each manufacturer might suggest different things.

  • 19 years ago

    The other thing to consider is that when you read something like "12 inch frying pan" that doesn't mean the bottom of the pan is 12 inches -- that's the width at the top, but the actual surface touching the stove is closer to 9 inches. What matters is the bottom diameter.