Software
Houzz Logo Print
warmfridge

More hood questions...

17 years ago

This is the first time I've ever shopped for hoods, and the more I look, the more confused I get.

How do I decide what CFM is adequate? I have a ceramic top electric range so BTU isn't helpful. My "kitchen" is one corner of an open concept house. While the kitchen space is about 16x13, the room is 28x26, and total CF is 5800. Do I need to allow for a certain number of air exchanges per minute or hour? I cook a lot of seafood and I need to eliminate fishy smells before they disperse through this airtight house.

Second question: Blowers. Internal ones are inside the hood. External ones are where??? Are these the same as inline blowers? Or mounted at the vent exit point? I don't understand the terminology. I'm looking at undercabinet hoods vented directly out the back through an exterior wall.

Finally, about cleaning. Are baffles those the grates with parallel bars that cover the undersurface of the hood, removable for cleaning? (vs. mesh) Does anyone have the "self-cleaning" Zephyr hoods where you spray cleaner onto the running fan blades to clean them? Isn't this a pain?

Thanks again.

Comments (6)

  • 17 years ago

    600 CFMs will be fine - higher CFMs are useful if you have a grill.

    An internal blower is in the hood. An external blower is mounted outside - usually on the roof or on the side of your house. An inline blower is mounted somewhere in the ductwork between the hood and the outside. Supposedly inline and external blowers reduce the noise somewhat but most of the noise is caused by the moving airflow, not the motor itself.

    Baffles are the grates with the parallel bars.

  • 17 years ago

    I strongly prefer baffles over mesh for cleaning. They just go in the dishwasher (as can mesh) and last a lot longer (ok, basically forever) compared to mesh. The mesh filters eventually need to be replaced, are not "generic" parts, and can be very expensive.

    Personally, I wouldn't choose a hood that I can't get the grease-catcher easily and regularly into the dishwasher. Some people don't consider that as strong a factor as I do.

  • 17 years ago

    More to worry about. If your house is truly "air tight" you have to worry about make up air. The 600 cfm blower weissman recommended will essentially remove all the air in your 5800 CF room every 10 minutes. That air has to come from somewhere and in a tight house that can lead to problems like backdrafting fireplaces or even worse furnaces, sucking CO and CO2 that is supposed to go up the furnace flue back into the house (the blower will suck replacement air down the furnace chimney in extreme cases-that air has to come from somewhere!). Older houses are so leaky (like my 250 year old colonial) this isn't an issue. You may have to have a make up air system of some kind installed or be very careful to open a window a bit every time you turn the hood. Depends on how tight your house really is.

    The other issue is more manageable. Again with a tight house you are rightly worried about lingering odor. This means you need a real hood, not one of those curvy glass pieces of art. You have to capture all all the cooking vapors and get rid of them. This calls for a large hood with a large, deep (top-to-bottom) inside that should be wider than your cook top by a couple inches on each side and the open underside portion (not just the front edge) of the hood must extend past the front edge of the front burners. The reason for this is that cooking vapors spread as they rise and you don't want them sneaking past the outsides of the hood. Sorry to be so long winded.

  • 17 years ago

    I wouldn't be too worried about makeup air at 600CFM. You've got to spend some real money and effort to make a house that air tight. That said, if you do use the vent with all the windows closed, you would probably reduce the efficiency of the hood. Best thing for you to do is simply open a window when you start cooking. The window doesn't even have to be in the kitchen. In fact one that's not too close to the cooking area would be best. A strong cross breeze from a nearby window can disperse the smoke and allow it to escape the hood.

  • 17 years ago

    Thanks for the responses.

    My house is very airtight, but there's a nearby kitchen window I can open, so I don't think depressurization will be a problem. Since this will be an undercabinet hood, its size has to be pretty much the same size as my range.

    I spent a lot of time on the internet and was amazed to discover no specific guidelines for determining CFM. One place recommended 100 CFM per 10,000 BTU for gas stoves, and a UK website had lengthy calculations using cubic meters per hour. The rest all seems to be guesswork.

    Decisions, decisions.

  • 17 years ago

    Its all guesswork for home hoods, and a lot of specs-manship on the home hoods as well. One manufacturer's "600 CFM" hood may only draw 300-400 CFM, even on a short duct run, and another's might actually come close to the claimed number.

    There is some work that has been done for commercial hoods, but little of it translates well to our "tiny" hoods which are very narrow, compared to a 10-foot or longer commercial hood. As I recall, hoods there are sized by CFM per lineal foot -- in either setting it's not removing heat that the objective, but drawing the vapors, smoke, and particulates into the hood.

    CFM/BTU is a nice guideline, but you'll likely need more airflow if you are charbroiling, searing, or pan/wok frying on one burner than if you have 6 pots of soup cranked on six.

    Make-up air is an art, and, improperly done, can actually make your hood less effective. In my opinion, unless you have a situation that can't stand even the hint of reverse pressure, such as a fireplace, a make-up air system isn't worth the trouble (unless mandated by code).