Software
Houzz Logo Print
heimert

Vent-a-Hood and 'CFM Equivalent'

19 years ago

We're looking at a vent-a-hood, and they list both a CFM and a CFM "equivalent". What exactly does this mean? CFM is a unit, but are they saying the blower wastes less CFM by being more efficient (i.e., the lack of baffles)? Or is it something else?

Also, we will have a 36 inch bluestar. We're planning a 42 inch VAH, with 24 inch depth. According to VAH, we could go either 600 cfm or 900 cfm. Any opinions on how much we'll need/want? Duct run is a bit long--about 30 feet with a couple of elbows.

Comments (9)

  • 19 years ago

    We have a VH and it's my understanding your explanation re: the CFMs is accurate. However, it's also my understanding that there are no real rules on how CFM are reported--it's up to the manufacturer so ratings are not absolute or directly comparable. Also, the size of the capture area of the hood (the actual volume the hood can hold) should also influence efficiency. Our VH is 600CFM, 42X27 over a 36" AG Wolf, with a 5' run and one 90 degree turn. While it works very well (we also have a grill), in a perfect world I would have preferred the 900CFM, but we couldn't accommodate the 10" ducting. With the the length of your duct run, the turns and the 24" depth, the 900CFM may be more suitable, especially if your hot burner is in the front and you do much stir fry or pan broiling.

  • 19 years ago

    We have a 36" 6-burner Bluestar with a 600cfm 42" wide 24" deep VAH over it. Our duct goes straight up and out of the roof of our 1-story home.

    I hightly recommend that you go with the 27" deep model. Whenever we use the front burners, some of the steam escapes the front of the hood, even when the hood is on high and it's the only burner being used. The 24" hood exterior does cover the burners completely, but the thing is, the front 3-4" of the inside of the hood is a ledge that houses the lights and controls. The steam bounces off of that ledge and some escapes. If I had to guess, probably ~15% of the steam escapes. With the 27" deep model, the control ledge would be beyond the front burners, and that bouncing off of vapors would probably be eliminated or at least greatly reduced.

    A 900 cfm hood that's only 24" may correct the problem too, but I couldn't be sure. It's just I can literally SEE the vapors hit that control ledge and be deflected out of the hood.

  • 19 years ago

    VAH does not use baffles or filters. There is less restriction in the airway. Restrictions in the form of baffles, mesh filters and such will reduce airflow when clean, more so when they get dirty.

    What they (VAH) claim is that without these restrictions the unit can maintain a eqivilent higher CFM rating as compared to other mesh / filter types.

    Some prefer one over the other and each has it's advantages but in the end a hood is a hood. Just pay attention to capture area (size in width depth and height) and you should be good to go. 42" over 36" cooktop is good. 24" vs. 27" depth is something to think of also. I sometimes wish I had gone 27" deep but maybe I would be hitting my head on it more ?? dunno

    With the long run you have it would be wise to go higher cfm than the minimum suggested cfm.

  • PRO
    19 years ago

    Yea be aware that HVI is the only independent company to verify hood power...and as of yet only broan uses them

    not to say the VH isnt a quality product because it is, but as a salesperson I have trouble believing its 50% more efficient than a baffle system, typically restaurants use baffle systems

    more important though is that long run(which with elbows is probably closer to 50 or 60ft) you should definitly oversize some, i'd recommend a real 900cfm(not VH's equivalent) at least

  • 19 years ago

    Thanks for all the thoughts. I'm working with our HVAC contractor on this.

    Turns out the 900CFM VAH won't work, because it needs a Y joint between the hood and the 10" duct. Since it's 18 inches high, it would leave no room for an elbow.

    It's looking like our choices are somewhat undersized or going to an inline duct.

  • 19 years ago

    When it comes to ventilation the best rule is to over size, over power and find a qualified installer.

  • 19 years ago

    "Turns out the 900CFM VAH won't work, because it needs a Y joint between the hood and the 10" duct. Since it's 18 inches high, it would leave no room for an elbow."

    While I don't know the layout, you also can run a 6" duct off the single blower and an 8" off the double, which eliminates part of the height issues with the larger single transition piece. Then they can be joined into a single 10" round (either at a turn or on a straight run where there's room), or they could both be run all the way to the external wall (albeit there would be 30' of a double run). As long as they understand the basic physics of air flow, you also can have custom transition pieces fabricated by HVAC contractors at reasonable prices.

  • 19 years ago

    If a hood is properly rated for CFM such as the HVI rating then it is rated with the filters in with a specified amount of duct run. More like a real live installation. Vent-a-Hood does not have their hoods tested by an independant certified testing agency. So I would go by the rated cfm a the best and not pay attention to the inflated cfm numbers they have. If it's rated at 900 then compare it to other 900 cfm rated quality hoods.