Software
Houzz Logo Print
helenab

Laticrete choices

14 years ago

We are about to install tiles in our shower and I am looking for clarification on the type of products we should be using. The walls and floor are covered with kerdi. The shower wall will have 12 x 12 porcelain tiles. The niche will be covered with 3x6 glass tiles and there will be a 1x1 glass mosaic accent strip. There will also be a pebble floor.

I want to use Laticrete, but there are a number of different products.

1) Beneath the glass tile and the glass mosaic, it seems that we should use 254 Platinum thin�set mortar (recommended by tile manufacturer) or 255 (recommended in this forum). What�s the difference? Which one to use?

2) Also, would it be ok to use conventional thin-set for the porcelain wall tiles, instead of Laticrete?

3) The tile grout line for the field will be 1/8 and the glass tile will be 1/16. There are a number of Sprectralock choices. Spectralock Pro Premium Grout seems to be suitable for glass tiles. Which product to get?

4) Also, could we use the same grout for the wall tiles as well?

5) I assume we�d get the Laticrete 1500 Sanded Grout for the pebble floor. Right?

Even though there are a variety of colors in the tiles and pebbles, I am thinking of using the same grout color to tie it all together.

Thank you!

Comments (2)

  • 14 years ago

    1) Beneath the glass tile and the glass mosaic, it seems that we should use 254 Platinum thin�set mortar (recommended by tile manufacturer) or 255 (recommended in this forum). What�s the difference? Which one to use?

    There are a couple of differences. First, the whole reason for the 255 is that it's a lightweight non-sag thinset. it's exremely sticky, which means tile on a vertical surface won't slide the way it does with most thinsets, including 254. Secondly, and most importantly from a technical standpoint, 255 has even more polymers in it than 254. It's literally THE strongest "mix with water" thinset on the market. This means it will exceed your tile manufacturer's specifications. It also means it'll be much easier to work with so long as it's mixed properly.

    2) Also, would it be ok to use conventional thin-set for the porcelain wall tiles, instead of Laticrete?

    I'd use the 255 for all of the wall tile, only because it makes it so much easier to install the tile. In fact, that IS all I use when tiling shower walls, INCLUDING over Kerdi, even though Schluter recommends against it (they don't like modified thinsets over Kerdi). Being you're using glass for part of it, you want it to be 255 WHITE.

    ) The tile grout line for the field will be 1/8 and the glass tile will be 1/16. There are a number of Sprectralock choices. Spectralock Pro Premium Grout seems to be suitable for glass tiles. Which product to get?

    Any of the Spectralock products can be used for all grout joint sizes. However, you might look at using their Permacolor grout. it ALSO has a fine sand in it, so it can be used for all size grout joints, and it IS stain resistant, even though it's still a conventional cement based grout.

    4) Also, could we use the same grout for the wall tiles as well?

    yes.

    5) I assume we�d get the Laticrete 1500 Sanded Grout for the pebble floor. Right?

    You could use the 1500 series, or you could still use the Permacolor. One tip on the pebbles-- you want to have TWICE ass much grout as you would for most installations of the same size, and moist of that will end up in the wash bucket if it's done properly.

  • 14 years ago

    Thanks for the advice. As soon as I saw this, I worked on successfully getting a couple of a bags of 255 to install tomorrow. (Not an easy task on a Saturday afternoon!) The vendor also agreed that it was the best product for the whole wall and the pebbles. Will look at Permacolor.