Software
Houzz Logo Print
chinchette

DYI Sonoma Tantrum backsplash help

18 years ago

I'm doing just three rows of Tantrums and a stone piece above that to end it off. I only need to cut three Tamtrum tiles. How do I do it? Also, do I need to seal the tiles before grouting? Should I just use mastic right to the wall? This is the very last detail of my two year project.

Comments (13)

  • 18 years ago

    Do you mean the Tantrum glass liners?

  • 18 years ago

    They make liners too. These are the one inch squares.

  • 18 years ago

    I'm doing a backsplash using Tantrum glass liners and 2x2 tiles as little feature tiles.

    Anyway, yes you can cut them. I am using a Roto-Zip with a diamond blade but you might be able to get them into a wet saw if that's what you're using.

    Remember that it is all cut glass. So when you cut them, have a tube of crazy glue handy. Be real careful how you pick up the tile after you cut it because all those glass pieces are now loose. Saturate the cut glass with the instant glue and set it aside with the cut surface face up and let it set up 'til dry. Then go ahead and cement it in place.

    I'm not using mastic--using a modified thinset.

  • 18 years ago

    I have no equipment because there will be only three tiles to cut for the backsplash and one liner. I will rent from Depot. However, since there is only three inches of tile to cut- could it possibly be nipped with a hand tool? What is a Roto-Zip? thanks.

  • 18 years ago

    I would never try to nip this tile. A Roto-Zip is a spiral saw--good for plunge cutting. But it also has an angle attachment and you can put a diamond saw on it for free-hand cutting.

    See if you can rent a small grinder. It will need an angle attachment and a diamond blade. I imagine you'll pay a premium rental price because of the diamond blade.

    You mentioned these are 1 inch tiles. I think you meant 2x2,yes? I THINK you could cut that on a wet saw if you don't have to take off very much. Maybe renting a small wet saw would be better. Don't forget to pick up some instant glue--one small tube is plenty.

    Another idea is to ask around to your friends to see if they have a Roto-Zip or a wet saw. Maybe they can cut it for you. If you were close to me, I'd cut it for you.

  • 18 years ago

    Yes, seal the glass liners and/or tiles before installing. We just installed Tantrum liners and it was recommended by BV here on this forum to seal them.

    Be sure to read the instructions that is sent with your order before installing.

    As for the cutting, I can't help you there, but perhaps BV will chime in.

  • 18 years ago

    Its only about 3/8 of an inch. I almost think it might be easier to chisel out that part of the window molding that the tile butts up to rather than to try and cut the tile.

  • 18 years ago

    DO NOT use nippers. DO NOT use a Rotozip. Either one will destroy the pieces. The manufacturer GAVE me a Rotozip and a couple of their new diamond bits about 18 months ago to test them out, and I can't believe they came out with them, anyway!! Even on ceramic tile, they were that bad, and I told them so. I figured maybe they wouldn't be bad for cutting strange shapes in cement board when prepping for something say, like a countertop, where there are radial cuts for the sink opening. it didn't even do THAT well!! As for the wet saw, they make special blades just for cutting glass tiles because normal tile and stone blades will chip the edge. My suggestion would be to mark the cuts and bring them to a tile showroom (or wherever you bought the tile) and see if they'll cut those few pieces for you.

  • 18 years ago

    So jealous here,I love Sonoma Tantrum tiles. Please post your pictures when your done. Also please share if you found a goood price.

  • 18 years ago

    Thanks all. I think I can get my friend to do a few cuts. They are one inch on mesh back.

  • 18 years ago

    How could you do that on a wet saw?

    Just as easily as you do it with a piece of tile, provided you have the proper blade for it.

    As for the Rotozip, they must have come out with some better bits than the ones they asked me to try out, because those bits SUCKED, and I guarantee you if you were to use them on glass, the piece would be unrecognizeable by the time you were done.

  • 18 years ago

    I don't have instructions with my tile. So do I need to seal with a penetrating sealer or just a plain old sealer? Do I need to seal the edges?

    Green-zeus, is there a problem with mastic with these tiles?