Software
Houzz Logo Print
donvon_gw

cabinet coat has brush marks??!!

19 years ago

After reading all the accolades about cabinet coat paint, I bought 4 gallons to paint our new home's trim. The painter called me over to the house today as he didn't think I would be happy with how the trim was turning out. The paint is not very smooth - you can see the brush strokes and it doesn't seem to be self leveling at all. We have pre-primed MDF trim and I don't know if that makes a difference or not.

My painter says he has not used cabinet coat before so I don't know if you need special brushes or not. Could someone help give me details on how to apply the product with the best results?

Thanks so much--

Comments (5)

  • 19 years ago

    It's not the paint! It's the application and or applicator.

    The substrate must be smooth with NO brushmarks in the primer. Any brushmarks in primer will telegraph through and will appear in the CC.

    Your painter has never used CC? It's likely that he or she is back brushing into the paint. Once CC is layed on, you cannot go back into the finish. It's like any other true waterborne; Impervo, Muralo, Pro Classic, etc. It pushes the water out immediately and cannot be touched after layed on.

    The brush is very important. I use a (GenX) chinex brush only. A synthetic brush does not release the CC fast enough for my preferences.

    You'll need to sand out the brush marks with 180 grit aluminum oxide sandpaper. Practice the application technique to get it right.

    Michael

  • 19 years ago

    In the years I've been using CC I've not had any issues with brush strokes except in a couple scenarios as Michael mentions: ridges in the primer and brushing over CC that has begun to set up.
    I'm no pro, just a gal that likes to paint ;) Our new trim was preprimed poplar, but I still had to lightly sand some drips and bumps out before applying CC. And wipe with a vacuum, tack cloth and then clean damp lint free rag to get any sanding residue off. Preprimed MDF tends to be smoother, my guess would be either they're recoating too soon, loading brush too heavily, or dragging the brush back through after CC has begun to set.

    When I first started using CC, learned that the hard way. (A small job, I had to let surface dry, go back and sand it smooth and start overt.) Once CC has started to level, if it's brushed back over too late after application the result is much like dragging a brush through Elmer's glue that has begun to set up. It will create a goobered up mess. It's been my experience there is a small window of opportunity to go back and brush out any drips/runs developing. My method was to paint the surface, move on to the next area, but closely watch for runs/drips where I had just been, and immediately brush them out. If it was more than 10 minutes or so and I went back over that area, I'd be making brush marks.

    Is it possible your painters are re-coating too soon? (I ask because I once witnessed a 'pro' painter do a family member's foyer walls with primer/1st coat/2nd coat back to back.) CC must be completely dry before another coat is applied.

    With CC, I learned it's far better to load the brush with about half as much as one would if they were using 'standard' latex paint. It will still cover well, and if applied too heavily, it will create many runs/drips that if brushed out too late will leave marks. (Often runs will not develop for about 20 minutes on some surfaces, so it's best to avoid those ahead of time.) It really does pay to take a scrap piece and practice a bit before diving in, doesn't take long to get the feel of it and saves a world of grief.

  • 19 years ago

    Hello Donvon,
    As usual, the above posters' have excellent points. The best finish w/ CC comes from good prep...AND staying out of the paint after TWO minutes...
    * Nice, even, & not too thick is the key.
    * After just a few strokes, get out of it...let it level.
    * If the painter is only waiting an hour or two, IT'S TOO SOON!
    * I gave sample-boards I did an overnight dry, on a sanded primer, and lightly (220-grit sponge) sanded the first coat of CC the next day. I then removed all dust, and applied 2nd coat of CC. The next morning I looked at my board...WOW! When I show customer's, they usually go "Wow" too!

    Faron

  • 18 years ago

    My new paint grade cabinets were painted professionally, there are very visible brush marks as well as bleeding on the new cabinetry. The Millwork is MDF and has large speckles and bumpiness, the spackled areas are raised and uneven standing out from a distance. The MDF is rough in places as on window sills and chair molding. The nails marks are visible on the wainscot from a distance. There are also heavy runs and sags on doors, wainscot, ceiling and dentil molding. We were given a bid and painter has given a final invoice exceeding bid by $4000- what do you all think?

  • 18 years ago

    Well you shouldn't pay for rough wood, runs, sags and poorly sanded spackled areas. The invoice exceeded the bid by $4K with no warning, reason or change orders?

    Personally I hate painting MDF. It's hard to fill nail holes because the MDF puffs out when a nail is driven into it and the brush marks don't subside as nicely as they do when you are painting real wood. A good painter should of course be able to paint MDF and have good results but the fact that it is MDF is certainly a factor.