Software
Houzz Logo Print
amberley_gw

Advice needed on 'reclaimed' marble countertops

18 years ago

I have an opportunity to buy two sections of marble countertop: one 8'5.5" long and she says 24" deep by 1" thick. The other is 6'9" long and 24" deep 1" thick. I am not sure if these measurements are 100% accurate yet. It is described as "white with caramel veining throughout". I am hoping that they are actually a little deeper than 24".

I have not seen photos yet-the seller is getting them to me hopefully tonight. Story is that she bought her house last year, and the seller had bought them "reclaimed" and had intended to install them but never did. She did granite instead.

My questions are:

Can I find a fabricator who will cut this for me to the size(s) I specify? Can I have it honed as well? (She said it is not super shiny but not honed either). The big one is: can I have these two pieces "laminated" to create a thicker profile??

This would require some creative rejiggling in my concept in my head (see current "chef's table thread"..) but if the marble is what I am after...it may be worth it.

By the way, both pieces are only $200!

I will post pics as soon as she sends them-hopefully someone out there might know what marble it is!!

I think I have become TKO!!

Comments (13)

  • 18 years ago

    i have no answers for your questions but that sounds like a fantastic buy. I just want to tell you I hope everything works out in your favor, its too good to pass up. Cant wait to see the pics!

  • 18 years ago

    I am going bananas waiting for the pics!!

  • 18 years ago

    I am really hoping some of you guys see this and have some thoughts.

    The seller won't have pics until tomorrow afternoon, but she did say that the counters are 25" deep (whew!) and less than 1" but more than 3/4" thick.

    I am so anxious....

  • 18 years ago

    Bump ... sorry, I have no answer.

  • 18 years ago

    That's a very good price - if I were you I'd contact some fabricators in your area and see what they say. Even if you purchased new, the cost of the material is generally low compared to the fabrication and installation costs.

  • 18 years ago

    What a great price-have you contacted any fabricators? I think this may be a great deal-but no idea if you can find someone to do the work?

  • 18 years ago

    It shouldn't cost too much to have them refitted since half the fabrication is done, but they will still have the cutting, any sink or other cutouts and the installation. Keep in mind that if there are any tiny cracks you don't see they could give way as the material is being worked or set into place -- or if a piece is dropped -- and there won't be another slab back at the yard to match it.

    There is some risk, but sounds like it's definitely worth looking into. I'd be willing to try it.

  • 18 years ago

    I bought my piece of marble for $50. My stone guy took it with the soapstone I had and polished it and brought it back and installed it. I wouldn't laminate them for a thicker profile but would look at possible edges that you can do to give the appearance of thicker . That way you have two pieces to work with in different areas. My marble is 1 1/3 " thick and my soapstone is 1 1/4" thick. I am not sure why folks need thicker counters as these look plenty thick to me. I am looking forward to seeing your pics. Just my opinion of course :). Caroline

  • 18 years ago

    The fabrication is the REAL cost in any type of stone countertops. I'd expect that those costs will be significant, because not that many stone places will want the potential headache of dealing with slabs they didn't source, as well as it being a relatively small job to begin with. Before you get too attached to the idea, please find out what someone will charge you to do the fabrication you need. It really might not be that significant a price diffrence between that and new slabs that you select yourself. Of course, in this construction down market, you might get lucky and find a place that will cut you a deal. If that's the case, just make sure they have been in business long enough to really know what they're doing. There are a lot of fly by night "buy a container load from China and set up shop" stone places going under right now.

  • 18 years ago

    I am so sad :(

    It turns out that when the seller went to take the photos, she turned it over and saw Corian sticker on the bottom. I am crushed...

    I spent half the day thinking- it could be statuary, it could be calcatta.....

    Back to the drawing board, literally!!

    Thanks for all you insights!

  • 18 years ago

    That's a real bummer. I was getting so excited for you.

  • 18 years ago

    Amberly,
    If yourneeds are this small you should locate a few fabricators and check out their remnant yards. SOME will work a deal with you on different levels. $200 for a couple of scraps was not a REAL bargain. a good deal but not a bargain.

    As was said by weissman, the material is normally a small portion of the actual job.

    Blessings

  • 18 years ago

    LOL Poor thing can't tell marble from Corian. I'm sorry for your disappointment, but I'm glas there was a sticker to guide her. But how did she not see that in buying them and looking at them for the job she was going to use them for? Oh well.....

    My slabs were less than half of the cost of my installed countertops, so having the material doesn't mean getting them installed would be super cheap. You have the material and some of the fabrication done. but even if there wwere no other issues, any craftsman is going to need to cover his costs for a job and travel to the job that may be all he does for that day and whatever time he spends getting the material ready beofre that. You'd probably run into minimum job charges.

    Good luck finding your countertops!