Software
Houzz Logo Print
dody40_gw

Hanging a Tapestry?????

13 years ago

My son gave me this Tapestry for Mother's Day. I have it up on the wall right now with thumb tacks. I am thinking to hang it properly, I could put a casing on the back and hang it from a curtain rod. It is 57 inches wide, not counting the fringe, I think I need to pull it to the right another inch or two. Am I right in my thinking, or is there a better way?

TIA,
dody

Comments (23)

  • 13 years ago

    I bought a tapestry years ago, and it came with a wrought iron rod with Fleur de lis finials on each end, so you are exactly right.

    I wonder, though, since this didn't come with a casing to hang it from, and appears to have fringe on all sides, if it's meant to be a throw/blanket, rather than hung?

    I found some online that are called family photo afghan/throw blanket/tapestry, which are 38x54". Is that the size of yours?

  • 13 years ago

    It probably was meant for a throw, but I have no place to display it. I already like what I have on my couch, so I figured I could hang it. Sister Shirley also suggested that I get a slat of wood to use instead of a rod, but I am not sure how to do that.

  • 13 years ago

    A curtain rod would be perfect, as it'll come with the hanging brackets you'd need, too. It will need to be a strong one, as that is probably quite heavy. As I mentioned, my rod was wrought iron.

    I've put a link to a wooden one below on eBay, which may give you some ideas. It's only 50.5 inches wide. You may be able to find similar brackets somewhere.

    Here is a link that might be useful: Wood Tapestry Banner Hanger Hanging Rod

  • 13 years ago

    I can't help you out, but what a thoughtful gift!

  • 13 years ago

    Thanks

  • 13 years ago

    I don't know how it would work with the weave of the fabric, but can you sew a sleeve along the back? My picture (which is upside down, sorry) is a quilted wall hanging and the quilter has those 2 sleeve type sections sewn onto the back to hold the hanging rod.

    Then you can hang it on a decorative curtain rod with pretty finials.

    For your blanket, I wonder about the weight of the fabric and the open weave making it difficult.

    Edited to add: How odd. On my iPad the picture is upside down but when I looked on my laptop it wasn't. So I don't know how it shows to you. I hope the picture still shows after I add this edit.

    This post was edited by hhireno on Wed, May 15, 13 at 10:22

  • 13 years ago

    I have one of these holding a large quilt my grandmother made. I did not want to sew a casing to it, or put holes in it. This just pinches the edge of your quilt or whatever textile art you want to hang. It mounts on two screws in your wall.
    There are probably other websites for this type of hanger, this is just the first one I found under google. Lots of sizes too.

    Here is a link that might be useful: Quilt hanger

  • 13 years ago

    My tapestry is smaller than yours, but I hang it off a rod by loops of fabric that were sewn on the back...a little less obvious than a full-blown casing.

  • 13 years ago

    How about framing the tapestry like a picture? In a frame contrasting with the wood paneling? This way it would stand out better against the busy wood grain background.

    If to frame like in the picture in the link below, you could fold the fringe over the backing board. My parents have a vintage tapestry with an Alpine scenery framed like this in their LR.

    Here is a link that might be useful: French framed tapestry

  • 13 years ago

    Another way to frame textile art that leaves the fringe visible - in the link below.

    Here is a link that might be useful: Tapestry framing

  • 13 years ago

    Oh my gosh, I was so confused initially! That's some realistic tapestry! I thought I was looking through an opening in the wall and people were standing in the room beyond. I wondered, "so where's the tapestry?"

    My husband and I bought a heavy woven wall hanging in Australia and then took some time figuring out how to hang it. It already had a sleeve on the back, similar to what another poster is showing. I actually pieced together the "hardware solution" - I bought a narrow round black curtain rod with decorative finials (just a simple curl - wrought-iron look) and fed that through the sleeve. I didn't like any of the usual curtain rod hanging hardware, and so I bought two black hooks - the kind which are often used on the ceiling to hold hanging plant pots. These were installed on the wall, hooks curling up. The curtain rod is set into the hooks, and can easily be taken down but is securely in place. Everything looks like it was sold together.

    I don't believe the hooks are in studs (the hanging isn't THAT heavy, and I can't imagine your throw/tapestry is, either) but I think we used anchors. If you have a sewing machine you could probably pretty easily sew a similar-colored sleeve right across the back of the fringe. That way, the fringe would still appear to stand up, rather than flopping down, when the tapestry is hung.

  • 13 years ago

    One other low-impact option, which is better than thumb tacks and super-easy, though not the absolute best solution, would be to use Velcro tape. If your tapestry is as I think it is (throw-like), it is probably light enough to be held up by a strip of heavy-duty Velcro. You could add a few stitches to the tapestry side just to ensure that the tape wouldn't come off. The adhesive alone should be enough to stick to the wall (or you could also add a few flat thumb tacks to the wall strip for extra security.) Or, if you don't want to put something sticky on your wall, you could use small brads to tack down the whole length of the wall strip.

  • 13 years ago

    I had the casing fabric all cut out to put on the back, when I went down to where Larry had bought the tapestry (OK, couch throw!) to check out how they had hung them for display. They had folded the fringe back in under and then hung it from hooks.

    I folded the finge in under and measured six inches in between each push pin. It looks very nice, and for now, I am happy with it. Hubby went nuts when I said I was going to hang it from a rod, so I did this temporarily.

    At a later date, when he forgets, I may do the casing and rod thing with it. I have a very nice rod that I think would look right. (I love all the samples of hanging materials that you gave me, but with all the hospital co-pays and high med costs that we are enduring right now with Gary's SECOND hospital stay, as well as from his first stay, I can't really spend more money right now.) It cost me $160 dollars to have the picture on canvas mounted and framed, and I am still reeling from that. The canvas picture is in my dining room

    Yes, hhireno, your picture is right side up and it confused me, trying to picture it upside down. lol

    my3dogs, it is 57 inches wide, not counting the fringe.

    As a side note, I know the paneling look is not for everyone, but I actually like it, and had my son put it up for me.

    dody

  • 13 years ago

    The push pins reflected the light from the flash. They actually don't show up at all.

  • 13 years ago

    That seems like an okay solution to me.

    I actually bought my rod/finials/hooks at Target, I think, and they were really inexpensive. You could use any old scrap fabric to make the sleeve, so the whole project shouldn't cost very much. You could even use a wooden dowel if you didn't want something which would stand out against your paneling.

    What's the objection to the rod? Poking holes in the wall? I've been using 3M "Command hooks" for a lot of projects now and they now come in a variety of decorative looks, and the larger ones hold quite a lot of weight. They stick tightly to surfaces but come off cleanly. I use one on the glass window of my front door to hold a wreath which weighs a few pounds. That's another option for holding your curtain rod.

  • 13 years ago

    I am not sure what his objection is, if you remember at all, Gary had a fit when I wanted to open the living room back up. I am not sure why unless it is because he is incapable of helping, and he hates for me to be doing anything. I cannot sit still for too long, so that does not work for me.

    I already have a good rod and brackets that will work, but I have to make the change when he is sleeping. I have the casing fabric all cut and ready to sew on.

    I thank everyone for giving me advice on how to hang it.

    dody

  • 13 years ago

    I have hung several smaller oriental rugs on the wall. I always use carpet tack strips. Cut them just a tad shorter than the width of what you want to hang. I like to use them because then I don't get any sagging along the top of the piece I'm hanging. Obviously you want to hang the strip with the "tacks" curving up not down. This won't do any damage to your item.

  • 13 years ago

    Good job Dody: it looks great in that spot.

  • 13 years ago

    Wooden quilt hangers?

    Here is a link that might be useful: quilt hangers

  • 13 years ago

    I'm glad you found an inexpensive solution, the best kind! You did a nice job keeping the top level and keeping it flat to the wall, probably not an easy task when working without a second pair of hands or eyes to help you.

  • 13 years ago

    Just an idea, but I noticed you already said you had the casing cut. When I hung an old quilt in a former home, I cut the top of an old flat shee, the hem part, it was perfect for the casing, already pressed and sewn, I just had to sew it to the quilt.

    Just FYI for future reference.

  • 13 years ago

    Those are wonderful photos of you folks! I didn't know they did photos on tapestries like that.

  • 13 years ago

    I don't think I should do a more permanent solution right now. Come fall, (unfortunately) we have to close this room back off and move back into where the dining room is now. I just am not sure how (or where) I will hang the tapestry. Oh decisions to make, Woe is me!