Software
Houzz Logo Print
joanneswimsct

need Jandy LXi rear vent kit

17 years ago

Hi all!

We have an indoor/outdoor pool w a telescoping enclosure. Our Jandy heater was placed inside the enclosure and was never vented. In order to use it we have to open both end doors and the 4 windows. Kind of defeats the purpose if you know what I mean! Our gas guy was supposed to vent it back in Mar but that hasn't happened. Long story short I called Jandy to circumvent the gas guy but they won't sell to me. Gas guy came out in mid Oct but found he was missing a part. Said he'd be back a day or 2 later but once again he's been a no show. Does not answer his phone and his voice mail box is full. Any great ideas as to my next step? I haven't paid the gas guy anything but as far as I'm concerned he is unreliable and I want nothing more to do w/ him. Someone suggested an ebay store for the rear vent kit but who installs?? As always, thanks to you all for your input!!

Joanne

Comments (7)

  • 17 years ago

    Most AC/Heating contractors can do this, and should do this work.

  • 16 years ago

    From the manual:

    3.1 Combustion Air Supply
    The heater location must provide sufficient
    air supply for proper combustion and ventilation of
    the surrounding area as outlined in the latest edition
    of ANSI standard Z223.1 (NFPA 54) or in Canada,
    CAN/CSA-B149.1, and any local codes that may be
    applicable.
    In general, these requirements specify that the
    room in which a heater is installed should be provided
    with two permanent air supply openings; one within
    12 inches (305 mm) of the ceiling, the other within 12
    inches (305 mm) of the floor. All indoor installations
    must have openings to outside air for combustion,
    ventilation, and dilution of flue gases from inside the
    building. See Figure 7 and Table 3. Jandy Pool Prod-
    ucts, Inc., does not recommend indoor installations
    that do not provide combustion air from outside the
    building.

    The same goes for Pentair and RayPak. This is the main issue when installing a heater indoors. Getting the exhaust out is easier than getting a combustion air supply in.

    You might move the heater outside or build and enclosure that meets the specs.

    I don't remember how much air space is between the enclosure and it's rail system. It might provide enough combustion air so that only venting outside is required.

    Scott

    PS: Did you try the dam suggestion to keep the rain water out?

  • 16 years ago

    Thanks guys for the info.
    Scott we didn't try the dam system as my husband was fearful of a tripping hazard. We are also already fighting a serious mold problem w/ some standing H2O so are concerned about using the dam as we'll end up w/ even more standing H2O.
    As far as getting outside air in w/ the heater I think we'd have enough. There is space in b/ each module, in b/ the end walls and the deck and at the junction of the deck and end of each rail. I believe Libart said we get air turnover a few(?) times per day????
    Spoke w/ a heater installer guy who suggested we buy the vent kit from ebay but haven't found exactly what I need; only the heaters themselves. Guess a phone call couldn't hurt. Heater guy said it'd cost a lot less for us to buy than for him. He will install for $100... Also looking for an air heater as we no longer have sun on the enclosure so the only heat comes from the H2O. Gets foggy very quickly now and H2O loses heat fast. Too bad we couldn't harness any of the heat thrown off by the pool heater as it gets nice and toasty inside even w/ the doors and windows open. The risk of CO poisoning is too great to hang out nearby, tho!!!
    Joanne

  • 16 years ago

    Joanne, don't have a clue about the vent, but when I read your post, I remembered I showed my husband your pool and post about the water problem. If I remember correctly he said he would add an overlay from waters edge and taper outward toward the rails,and on the outside of the rails, grind down the concrete to taper away from the rails and add a thin overlay to cover the ground away concrete. Of course, if it was his pool, he would totally remove and relay the deck, but he's a fanatic for doing things right. It is probably too cold there to do anything til spring, but keep us posted. Happy Thanksgiving, Barb

  • 16 years ago

    Id just cut in deck drains to re-mediate the issue

  • 16 years ago

    Yes Racket, we agree, but were looking at esthetically pleasing as well. I hate the look of deck drains, breaks up the look of a large area. She may also have mold or algae problems with them, but it would be a much cheaper fix. Sure hate to see anyone have problems like joanne's, she has a sweet setup. Barb

  • 16 years ago

    Hi Barb and Racket
    In a perfect world we would start all over again but the price is outrageous and I just can't justify paying so much for someone else's mistake.
    Barb you are right; we are now battling a mold problem. We spent a few hours at the pool yesterday a.m. scraping, chloroxing, rinsing and vacuuming the mold buildup that has been taking over since the building has been closed. Way too much moisture as we have yet to purchase any heat source for the air. All we've used so far is the heat of the water once we take the solar cover off to warm up the air. It's nice except the moisture runs down the walls and back into the pool. What doesn't make it to the pool sits in low spots on the deck and grows mold. Yuck! We've tried squeegee-ing the water out but it just flows right back in under the rails as we are pitched in from outside a bit as well as inside... At least if we had a drain we could squeegee to it plus pour chlorox in every now and again to kill anything in the standing water.
    On a different note we met another gas guy who took the time to research our heater's capabilities plus called Jandy to verify that we DON'T need a rear vent kit but can use the existing vent situation on top of the unit and elbow out the wall. We save a bit by not needing the rear kit and just using an elbow and short piping and collar at the wall. Guy seems sharper than our original contact and has been out 3X so far to check the situation out. He should be able to do the job by the end of next week. His charge is $100 while the original guy wanted $300 plus parts. I hope we catch a break finally as we sure could use one!! I must say, though, we had great luck w/ both our fence guy and our landscaper. Anyone in CT looking for fencing check out Sunset Associates and for landscaping try 3B Lawncare. Top notch, professional and worked together in a timely fashion to be sure both jobs were done right.
    Hope everyone had a great Thanksgiving!
    Joanne

0