Software
Houzz Logo Print
imrainey

Pre-shrinking fabric

17 years ago

I didn't used to pre-wash unless I suspected bleeding dye. Now I do to control shrinkage. But I got in a discussion yesterday in the fabric shop about what actually causes the shrinking.

I use really hot water and iron the fabric with a hot iron when the wash cycle is done. I thought that would do it because heat is what caused the shrinkage. But other people said that they thought the trick was to use cold water to set the dyes and heat in the drier to shrink the fibers.

I am resisting the idea of tumbling in the drier because I just hate having to cut apart all the raveling threads that enmesh in the drier. Batiks aren't too bad but conventional weaves just come apart! Plus, I know that I've had shrinking because on the conventional weaves -- and occasionally the batiks -- I have to snip the selvages to get the fabric to lie flat. But is it enough?

What do you do?

Comments (7)

  • 17 years ago

    Shrinkage in natural fibers is caused by sharp changes in temperature. If you wash the fabrics in hot water, with a cold water rinse, then hit them with the hot iron, they will shrink for you. I agree with you about some fabrics--you can actually watch them shrink under the iron! Fabrics shrink more along the lengthwise grain (the warp) than along the cross-wise grain (weft) which is why selvedges will sometime shrink more than the body of the fabric--there are more warp threads per inch along the selvedge.

    I wash my fabrics in the sink with the hottest water from the tap until they stop bleeding (and, yes, modern dyes WILL bleed!) then rinse them in cold water and either hang dry or press dry depending on time and my mood. I choose to prewash because my fabrics are rarely selected for a quilt that I'm going to keep and I don't the recipients to inadvertantly ruin a quilt by washing it incorrectly.

  • 17 years ago

    I wash darks and brights in the sink in hot water and Retayne then put them in the dryer a while. Sometimes I'll iron them, but not always. Pastels get washed in the washer on hot and put in the dryer. I don't like the ravels either, and sometimes I'll iron a little piece dry, but mostly I just snip and rip off snaggles as I fold.

  • 17 years ago

    I prewash everything and add retayne which controls color runs. I think what you do is quite sufficient to get the shrinkage out. I usually iron my fabrics unless I had a lot of fabric to treat.

    I would either prewash everything or do none if I am doing it to control shrinkage. A mix in my opinion doesn't work well.

    A tip: if you are washing bigger yardages 2 yds +, I open the fabric out and accordion fold it along the selvage in about 3/4yd lengths. Then pin along both selvages and this will keep your fabrics from getting all tangled up in the washer or dryer.
    Jean

  • 17 years ago

    A hint as to how to keep fabric from raveling in the dryer:
    Cut a small triangle from each corner before washing and drying and it stops the raval. Another method that I have used is to serge the ends but since I have started to clip I have not done that. Jayne

  • 17 years ago

    Yes, I absolutely agree that mixing would be a mistake. I'm beginning to work backward to the prints I've had for ages. Right now I'm keeping the pre-shrunk and the unwashed in different rooms but it's getting ungainly to keep track and I'm tired of having to wash in the middle of a project because an unwashed fabric is better.

    Thanks for the tip about large pieces. I haven't dealt with any yet. I'll keep that in mind.

  • 17 years ago

    Oooh! I'm going to try clipping corners too.

    So glad I asked and got some useful tips! Thanks.

  • 17 years ago

    Yup, clipping just a tiny corner really helps. Doesn't stop raveling completely, but just a few stray strings.

    beverly

Sponsored
Bella Casa LLC
Average rating: 5 out of 5 stars17 Reviews
The Leading Interior Design Studio in Franklin County