Software
Houzz Logo Print
bigyellow_gw

Having problems driving trim nails

18 years ago

Every once and a while you run into a problem that makes you feel like you don't know what you're doing. I've built a tool shed from scratch and right now can't drive trim nails without bending them!

Here's the deal. We have a screened in porch and after a couple of rain outbursts we've had recently, the roof caved in. I took the whole thing apart, as there was a ton of wood rot and started from scratch. New plywood, sheathing, roll-roofing and cement. I installed the drip caps and now am just trying to add some nice metal trim before putting on the gutter. I bought the white 1 1/4" trim nails and I can't, for the life of me, drive them without bending them. After about 25 nails and only getting 5 to go in (with VERY careful, tentative nailing), I tried pre-drilling holes. Maybe the holes I drilled were too small, as it seemed to make NO difference whatsoever!

Should I just break out my brad nail gun? It will do the job fine, but the nails are aluminum colored and not white. Then again, they're so small, I could just hit it with a dab of paint afterwards. However, since metal trim is installed all the time, my question is, what's the trick? How are you supposed to do this? My *guess* is that this is simply done with an air gun and you just have to find white nails, but I don't know. Thanks in advance.

Comments (6)

  • 18 years ago

    I laughed at your first sentence because the best of us have been in that SAME situation.

    Siding installers usually shoot staples. I actually hate those staples because they are so tiny,holding such a small piece of metal, that high winds can work on it and rip the flashing right off. I like nails a lot better.

    I repaired some flashing like this, just recently, and I drilled a pilot hole thru the aluminium that was slightly larger than the nail. Then drilled a smaller pilot for the nail.

    Are these nails really long? Sometimes these nails seem a lot longer than you need, and are prone to bending when you get close to a knot in the wood. If they are, cut them off and try driving them. I've cut nails and never ground a tip on them but they could use a pilot hole to make it a little easier.

    If the nails won't be seen, just use your air gun. You'd be surprised how no one will even see it.

  • 18 years ago

    Having taught many volunteers how to hammer nails(HfH crew leader), I found two basic problems when folks bend nails.

    1. The hammer face is not perpendicular to the nail---it hits the nail at an angle. This problem has two causes---angled hammer heads(head not perpendicular to the handle).

    2. Improper use of the hammer(hitting at any of several angles---off perpendicular/off vertical/on a bias).

    Either of the two can be caused by being nervous about holding such a small nail when hammering---fear of hitting ones fingers is a powerful deterrant to proper procedure.

    One way to prevent the fear factor is to hold the nail with a pair of regular pliers. Not needle nosed or slip joint types. The grooves in the plier jaws hold the nail securely and the nail can be aimed to be in line with the face of the hammer---with a little practice. The pliers also help support the nails and lessen the chance of it being bent.

  • 18 years ago

    Believe it or not, I'm one of those crazies who has no fear in getting his fingers smashed by a hammer blow! I think in this case, the nails are just so delicate that they simply would not go through the wood.

    I solved my problem by pre-drilling 5/32 holes. Before, I was only using 1/8. That extra 1/32 made all the difference! Thanks, guys.

    One more note. I'm really practicing hammering with a consistent, perpendicular blow. So far, so good. Again, thanks for your help!

  • 18 years ago

    First, no reputable siding installer will ever use staples. Staples are prohibited by Building Codes in most cases.

    Second, you are likley using aluminum trim nails. You should throw them away and use only stainless steel trim nails which will never bend under normal hammer installation. Stainless steel trim nails can be found in any color that aluminum trim nails can be found...and stanless steel nails will cost only slightly more than aluminum trim nails.

  • 18 years ago

    Does sound like you are using aluminum nails, and they are a bear! Predrilling usually works, provided you are drilling large enough and deap enough. And then a gentle "tap-tap-tap" with the hammer. If the nail bends even a bit, pull it out and try again.

    I've resorted to using a bigger nail and pounding it in a ways, pulling it out and then putting in the aluminum nail. It's a real drag when you are at the top of an extension ladder trying to get the peak of the fasia trim nailed down. I don't like hieghts!

    I like the idea of stainless steal trim nails, I have not come accross them, but have not looked for them either. Even if you can't find colored ones, I'd use them, and then a dab of paint to hide the surface. Half the time the paint comes off the aluminum nails anyway.

    Cathy

  • 18 years ago

    Buy an air compressor and nailer ... you will never pick up a hammer again!