Software
Houzz Logo Print
adichristi

Curtains out of

18 years ago

I put this in the sewing forum, but no reply's yet .

I was thinking about making some curtains out of some nice Damask (54% Cotton, 46% Polyester) tablecloths. Has anyone done this and how did they look? I was thinking of ring clips instead of a rod pocket.

Thanks.

Comments (14)

  • 18 years ago

    Are you asking if using tablecloths in general as the fabric for window treatments is a good idea or specifically a damask? It's a great use of fabric IMO and if a damask is what you love then go for it. I had roman shades made out of hemstitched table cloths - my sewing skills are WAY below roman shade level! - and I love them.

    The one downside I can see to your idea is that sometimes clip rings on a straight panel of fabric look a bit undeveloped - know what I mean? I find they need more detail to take them up a notch. If you have enough fabric width, try working a small pleat into each clip. It takes a bit of fussing to work the pleats softly down the length but it adds some needed definition to the top.

  • 18 years ago

    dlm2000, I was asking about damask, only because they are a sale item.

    I think you answered my question (clip rings on a straight panel of fabric look a bit undeveloped - know what I mean) about the look though.
    Do you have a picture of your roman shades made out of hemstitched table cloths? I would love to see them.

    Thank you!

  • 18 years ago

    I've used tablecloths before. Not damask, but cheap and cheerful Martha Stewart from K-Mart. I lined them with old sheets, and made rod pockets. Very easy. I did the rod pocket at the top, stitched the braid trim in the side seams (I'm explaining it poorly, but if you sew at all, you know what I mean) and did the two hems separately.

  • 18 years ago

    Sounds like that sale damask is a great solution. To make them hang well - you shouldn't need pleats -
    hang them on the rings
    pleat them by hand into the folds you want
    tie string loosely at top, middle, and bottom (or use big rubber bands) of the panels to hold the folds in place
    steam the folds (optional but recommended)
    let hang a couple of days (longer if you don't steam) before you remove the string

  • 18 years ago

    Using a tablecloth is a great idea - generally tablecloth fabric is heavier than, say, a sheet. However, the rings complicate matters a lot. Unless you are prepared to finish the top properly, the drapes are likely to droop. A rod pocket would be much easier.

  • 18 years ago

    chris in the valley - that's what I do to "dress" curtains, and it works well for stationary panels that you don't intend to close, or for curtains that have an interling to 'hold' the dressing even with opening and closing.

    asichristi - I don't know if the you intend to line these, if they are to be opened and closed or stationary panels. But as grawings said, the tops tend to droop without some stiffening. If they are to be unlined panels and you do intend to open and close, they'll lose the soft folds from dressing very quickly and you'll be re-dressing them often to keep them neat looking. I've found that pleating a bit with the clips adds a bit of structure and helps maintain a neater look. You may be going for a really unstructured look, and in that case - nevermind!

    These are the shades I had made. I did the same thing you are doing - bought them on sale but it took me years to actually use them.

    {{!gwi}}

    {{!gwi}}

  • 18 years ago

    Those look really nice! I never would have thought to use on-sale tablecloths as window treatments. Hmmmmmm

  • 18 years ago

    I've used tablecloths as 'fabric' for upholstery, but never even thought of window coverings~great idea for shades!

    I want to use a tie-up shade in my master bath, and this is the perfect solution and since the window is frosted, won't even need it lined. A little fringe 'glued on' and i'll be good to go. dlm2000, your Roman shades look fantastic! Such a great idea.

  • 18 years ago

    "I've used tablecloths as 'fabric' for upholstery, but never even thought of window coverings~great idea for shades! "

    Another GREAT idea!

  • 18 years ago

    I often look at table clothes to use as fabric. I made valances for the kitchen to match the table cloth and Martha Stewart Paint on the walls! Saved money and it all matched too!
    If it's made out of fabric and there's enough for what you want to make, no reason not to use anything for anything eles.
    Did that make sense? :^/

  • 18 years ago

    dlm2000, I think Country Curtains should hire you! Very nice shades. Did you use a pattern? How did you do them, if you don't mind me asking?

    I do want to open and close them. They would probably look a lot nicer lined.
    I agree with what everyone says. Thank you!
    Now, I have to do some more thinking on this.

  • 18 years ago

    adichristi thanks for the compliment but I didn't make my shades - that's way too much math for me! I have a friend who has a home sewing business and we make a great team - I get an idea and she makes it happen. I wanted tailored, crisp shades with just a little detail to make them special.

  • 18 years ago

    I've used tablecloths as curtains a few times. Just with a rod and clip rings. I didn't notice any sagging at the top, but it probably depends on the fabric. If something did sag, I'd just use more clip rings.

    My favorite curtains from tablecloths were some white matelasse ones that I had in my bedroom.

    One thing about tablecloths as curtains--if you have really tall windows, you can get long tablecloths that will cover the whole window for a lot less than pre-made curtains. Even if you decided to line them and make a header, it will still work out to be less.

  • 18 years ago

    All great minds think alike!

    I'm still not sure what I am going to do at this point.

Sponsored
J.Holderby - Renovations
Average rating: 5 out of 5 stars4 Reviews
Franklin County's Leading General Contractors - 2X Best of Houzz!