Software
Houzz Logo Print
kathec_gw

Question about stair treads.

17 years ago

I've got carpeted stairs. They are covered in builder quality off-white carpet the PO installed to sell. After 18 months, 2 adults, 3 kids, 2 dogs, it's getting pretty bad. I have a Bissell carpet cleaner, and occassionaly clean them, but they're already getting to that point where the stains aren't coming up and the fibers are flat.

I've been toying with the idea of ripping off the carpet. OK, I fantasize about it everytime I vacuum. I know that at least in the foreseeable future, I can't afford to have new treads and risers. Or, I should say that it's pretty low on the priority list to deck it out with the good stuff. So I've peeked under the tinest corner and see builder grade lumber with paint & texture overspray, tack strips, carpet glue and staples. I'm pretty sure with a bucket of Ready Strip, caulk, paint, and a runner I could get these to look reasonably good, at least for the next year or two.

Has anyone done something like this before? Was it successful? I guess I should mention that the house is a circa 1990 center hall colonial style, so the stairs are the first thing you see when you enter the front door. It's a straight run upstairs, no landing. After 3 test runs I still can't get a picture in the body of the message, so I've got a link. It's the original realtor's photo, so no, it doesn't look like this anymore.

Thanks!

Here is a link that might be useful: Entry/Stairs

Comments (5)

  • 17 years ago

    I've done this twice - I riped vinyl type flooring off one set of stairs, and carpet on another. At the first house, it was soft (read: dog nails scratched the heck out of the stairs) pine. So, I took thin planks of an oak veneer, painted designs for the risers(hey, I was young) and glued them back on. The biggest issue was joining the rise and the run, and I used a L piece of moulding to cover the line where they joined. Only problem that I had was that I used pine moulding, which was got beat up in no time.

    At the second place, I was lucky in that the treads were solid maple, and I tiled the risers with a nice Italian floor tile (border height so that it fit, displayed a pattern, etc).

    I now have carpeted stairs again, with builder rough lumber underneath. To make matters worse (or, more expensive), my railing spindles are attached directly to the treads, so railings would have to be adjusted etc if I were to replace the treads or try to cover them with hardwood. My hardwood flooring installer suggested hardwood veneer on the risers, and recarpet the treads for a new look.....

  • 17 years ago

    chloe s mom, I could see your problem with dealing with the spindles. I love the look of the spindles meeting the treads, but it's definitely more expensive. I guess that's why so many builders (like mine) go the cheaper route.

    For my stairs, I know I will definitely not luck out with maple. It's probably pine. I didn't dare peel away but just the tiniest corner of the carpet to see.

    I am hoping to get away with painting the existing treads, maybe even paint a faux grain and tack up a stair runner. That way it's just about 2 inches showing on either side. My stairs are on the narrow side. I would think that the runner should protect the pine a bit. I don't mind having a bit of wear, as the flooring in the entry is handscraped hickory with a lot of "chatter".

    Thanks for sharing your experience. I'm glad to know I'm not the only one to consider doing this.

  • 17 years ago

    Someone here did that - ripped out the carpet and painted - may have even been plywood treads, can't remember. But anyway it was beautiful when she was done. I know she came back at some point to show how it was wearing and she did not have a runner. Wish I could find it - didn't see it on a quick search. Maybe start a new thread with a title about painting stair treads and risers and you'll get more info.

  • 17 years ago

    I just found this site and thought of this thread. Now I want to rip out my carpeting (and wallpaper the risers!). I wonder if the lacquer would make the stairs slipper (presumably a runner would take care of this problem though)

    Here is a link that might be useful: painting lumber stairs

  • 17 years ago

    You can get a wood grain look by either using gel stain, my preferance, or Zar stains, and their woodgraining tool. Check video link below.

    Cabot makes a waterbase gel stain which is much less toxic than oil based stains. Cabot is sold at Lowes. It comes highly recommended from an old friend of mine that I'd trust with anything to do with paint or stains.

    Here is a link that might be useful: Woodgraining technique.

Sponsored
Bella Casa LLC
Average rating: 5 out of 5 stars17 Reviews
The Leading Interior Design Studio in Franklin County