Software
Houzz Logo Print
bicyclegirl1

Backsplash installation question

11 years ago

I'm helping a friend put her backsplash up this coming weekend. I've tiled walls, floors & backsplash before, but the ones I've done, were fairly good size tile that were pretty easy to work with. She's using 1x1" glass tiles that are on a large mesh sheet. It's probably about 12x12" & the sheets are pretty heavy. I wonder if we'll need a certain type of mud to put them up so they don't slip down before they dry. Or a certain consistency of mud? They're going up onto textured & painted sheetrock, if that's important. It's been awhile & I'm going to google to make sure I have the steps down, but if anyone on here has used something similar, I'd love to hear your experience.

Another thing I'm concerned about is, the glass tiles are kind of fragile. They can break pretty easily. It's a little intimidating thinking we may have to cut a little piece off one of those tiles. I've used little clippers when working w/ subway tiles, as an example. They worked great. With this tile, all that will do, is break one of those little bitty tiles in pieces. We'll have a wet saw, but that could be a disaster w/ cutting just a little edge, if needed.

Are we getting in over our heads?!?

If you have advice, please post! I'm going to do a double post onto the kitchen forum & see if anyone over there has tackled this.

Thank you in advance for your help.

Comments (6)

  • PRO
    11 years ago

    Use a modified thinset and you should be ok.If the wall is painted with a gloss paint it would not hurt to scuff it up with some 80 grit sandpaper.Those sheets of small tiles may want to sag on you so keep a close eye on them.

  • 11 years ago

    I have used glass tiles in the past--they were 2x2's on a mesh. If you use the thinset that comes pre-mixed, it is firm enough that the tiles don't slide down. And be sure to use the white thinset--not the gray. The grey can be seen thru glass tiles while the white doesn't interfere with their color.

    When I cut these tiles, I use a roto zip with a diamond blade and cover the tile in a good sticky tape before cutting. This will often prevent cracking, but you'll have to be very careful, and SOME will crack, especially along any inclusions in the glass. It's a DELICATE job citting these tiles, but it CAN be done. If you can't clamp the tile down to cut, use some double-back sticky tape to hold it down while cutting.

  • 11 years ago

    precision & green, thanks for all of the advice! I was talking to a guy today at Home Depot who told me about the thinset.

    green, you don't happen to be in Austin so we can borrow that roto zip, do you?!?! I'm not sure she's going to want to go buy one for doing just this job. But, someone was telling me about the dremel - I'm sure I'm not spelling that correctly! - & how to use it to cut glass tile. My friend has one, so we're going to look into that a little more.

    I'll post a pic when we finish it. Thanks for the help.

  • 11 years ago

    If you know the manufacturer of the tiles, see if they have installation guidance on their website, or call their tech department for information.

    Understand that "premixed thinset" and mastics which come ready-to-use in resealable plastic tubs can yellow over time. You may not want that behind a glass tile. Depends on opacity, etc. Mastic also cures by drying out. With uneven drying you can get a blotchy or mottled appearance on the wall. One inch tiles are small enough where they shouldn't prevent the mastic behind them from drying.

    If you do go with a true portland cement based thinset, then yes, use a white thinset as a previous poster advised.

    If you can use either, then mastics can be easier for DIY.

    Thinset and mastic are often put on the wall with a notched trowel. When using glass it's sometimes advisable that after you apply the thinset/mastic to the wall and comb it out with the notched side, to then knock the ridges flat with the flat side of the trowel. Ridges can sometimes entrain air and result in air bubbles behind the tile. Again depending on the properties of the glass tie, the bubbles may show through the tile.

    Have blue tape available. When you set a sheet, run blue tape across the sheet seams from one sheet to another. It can help prevent sheet creep. Don't be shy about using tape.

    Any cutouts, junction boxes, etc. If the tile are as fragile as you say, it might help to cut wide around and outlets, etc. Set your full sheets and partial sheets. Clean out any thinset squeeze out near the junction boxes.

    Let the thinset cure.

    Then come back the next day and you can fill in the cut pieces by hand. Put a blot of thinset on the individual glass tile, shmoosh it into place, run a strip of blue tape over it, pat it so the face of it is flush with its neighbors, and leave it be.

    Come back after the thinset has set, pull the tape, check spacing, grout, etc.

  • 11 years ago

    What do you mean by "textured" sheetrock? If it's some kind of stucco like coating, you may have problems with it. Otherwise. look to Mapei's Ultralite or Laticrete's 255 thinsets. Either one in white, both are highly modified non-sag thinsets

  • 11 years ago

    mongoct, thanks for all of that information! I love the blue tape tip! That makes such great sense! Also, I wasn't sure about the difference in mastic & thinset. I want to say I've used both, but it's been awhile, so I guess we'll go w/ thinset. Seems everyone talks about using that. And, white! Also, knocking down the ridges is great info, as well. Wonderful tips!

    bill, sorry, I probably should have been a little clearer on that. It's not highly textured, but just typical textured sheetrock. I'll check out the 2 thinsets, as well. I like the "non-sag" part!! Thanks!