Software
Houzz Logo Print
itzbinnice

John Deere SRX75 Rider Issue

11 years ago
last modified: 11 years ago

I have an old Deere SRX75 30" rider with a Kawasaki 9 HP engine. Kawasaki Model #
FC290V-FS10.

For the past several years I am having difficulty restarting it, more so in late
fall. When I start it I choke it and turn the key it usually starts that
way. I move the lever to fast and it runs ok.

The problem I'm having is once warm, the ONLY way it will start again is in
slowest setting, and that may take several tries. In the past it started right
away on slow (never on fast), but now it takes several attempts on slow to
start.

I had taken the carb apart and cleaned everything but it was very clean
inside. I always use Stabil and run the mower dry and drain all gas at seasons
end..

When I had the carb apart, I noticed there was no needle seat in the carb
that I thought may be the problem. I tuned the carb upside down and blew into
the inlet, it was sealed so I'm thinking that's not causing flooding when on
fast. I'm wondering, perhaps the needle is worn and permitting gas to flow when
the carb is installed having less pressure on the needle. Below is link for
schematic of carb:

http://www.dowdatractor.com/OemParts#%2fJohn_Deere%2fSRX75_RIDING_MOWER_(9_H.P_ELECTRIC_START)-PC2292%2fCARBURETOR_SRX75%3a_FUEL%26_AIR%2f22920002%2f2292C070C0303000002

Does anybody have any suggestions of what else I can check
to correct this issue.


Edited: Sorry I can't get the carb parts link to work.

Comments (6)

  • 11 years ago

    Well, I tend to think of hot restarts problems being ignition or possibly compression related. One wouldn't think that a float valve would leak only hot. Spark plugs and igniters get my first attention on these. You are correct that there is not a serviceable seat in these carbs. If you think that possibly fuel is passing the inlet, shut off the fuel valve 30 seconds before shutting down to test your theory.

  • 11 years ago
    last modified: 11 years ago

    SRX75 Electrical Components

    @tomplum
    Thank you for your reply and suggestions. I won't be able to test the until the
    spring since the mower is winterized and sitting in the shed.
    The first thing I will do is try the fuel shut off suggestion, next will be
    changing the spark plug and checking for good spark in all starting carb positions.

    I did change the plug at the beginning of last season but things do go bad
    unexpectedly. I also changed the ignition module over 3 years ago, at that time
    the mower wouldn't start at all. I see there is also an ignition coil which was
    never changed. Parts for these electrical Deere components are outrageously
    expensive and I can only find them at John Deere dealers.

    Oddly enough I can start the engine from cold, let it run a minute and shut it
    off. If I try to restart at fast speed it will not start, only at idle speed
    will it start. Not even anything in-between the two positions. This I would
    imagine would rule out heat causing it since it only ran for a short duration.

    This is the link for the electrical system, hopefully this
    time the link it will work when clicked on, if not copy and paste may work. This new Houzz site is proving difficult with links even though I selected insert link.

    http://www.dowdatractor.com/OemParts#/John_Deere/SRX75_RIDING_MOWER_%289_H.P_ELECTRIC_START%29_-PC2292/ENGINE_ELECTRICAL_SYSTEM_SRX75%3a_9_HP_KAWASAKI_ENGINE_MODEL_FC290V/22920002/2292B060B0102000005


  • 11 years ago

    A thing to try anyways . When you install the new plug, set the gap .020" and see if there is an improvement. Maybe start with a new air filter and don't treat/ oil the wrap.

  • 11 years ago

    Thanks for the tips, I'll give them a try in the spring when things warm up here. The cold spell here on Long Island is the worst in the past 30 years for low temps in February. With temps usually in the teens it makes no sense to do any testing..

    The plug was set at.030 as per manual I'll replace the plug and set to .020. Also, I always had put 3 drops of oil in the precleaner after washing it. I won't do that anymore. I also intend to replace the fuel filter in the spring.

  • 11 years ago

    weak coils are definitely a problem on aging deeres. If you can borrow one in the spring to try that would rule that out. Mine was problematic when it warmed up as well.

  • 11 years ago

    I don't have an extra coil, nor can I borrow one. I don't want to spend 80.00 for a new one unless I'm positive that is the problem. Part # MIU13323.

    I too was thinking possibly the coil since that was never replaced. But I'm not so sure that is the issue. As previously stated even running for a short time it will only start at slow speed, so the coil did not really get that hot.

    In the spring I will do the following test. Before initial start I'll remove the plug and crank it to see what kind of spark I get. Next I'll put the plug back in, start it and let it run awhile. Then I'll remove the plug and crank it once again and see if there are any changes in the intensity of the spark.

    I hate working on this Deere, they make everything so difficult to work on. Even changing the oil is not as easy as one would like due to the location of the oil drain pipe.

Sponsored