Software
Houzz Logo Print
fanninjosh

Ficus Deltoidea in Gritty Mix

10 years ago

Slowly getting everything repotted into gritty mix. I've just been using window screen over the drainage hole because it's all I had. What size screen does everyone else use? Any thoughts on how I should start pruning this? Not sure if I want to try it as a bonsai?

Comments (20)

  • 10 years ago

    Window screen is just fine...

  • 10 years ago

    I agree.

    I agree with Rina. I use Fiberglas insect screen or the plastic canvas used in some needlepoint projects.




    There is no difference in how plants respond to "bonsai pruning techniques" as opposed to "houseplant pruning techniques" because they are one and the same; and what would make a bonsai look has the same potential to make a houseplant look good. What separates a proficient bonsai practitioner from a houseplant devotee (when it comes to pruning and root pruning) is primarily the intimate familiarity the bonsai practitioner has with the process.


    FWIW - it's difficult to give meaningful pruning advice based on a single 2D image.

    Nice plant!

    Al

  • 10 years ago

    Thanks Al and Rina. I didn't use a wick on any of mine, though it did cross my mind. Is the wick to allow the bottom portion of the mix to dry faster?

  • 10 years ago
    last modified: 10 years ago

    Hi! I'm sorry I'm writing under somebody else's post but I posted a question about ficus benjamina somewhere else on houzz and got no answer:(
    I have a ficus benjamina that I have bought at home depot maybe 4 years ago. It has been in different room before and was losing leaves many times. I moved it few months ago to different room where it gets more light and I water less often. it doesn't shed leaves anymore and grows actually leaves on top, but the inside branches are dry and have no leaves and even on top some leaves grow small and later the branches on top dry up too. I would like the plant to look fuller and not so spindly, also I must say it did not grow a lot since I bought it. My questions are: should I repot it into gritty mix? I already bought it. If so, should I add gypsum to the mix or just fertilize it every time I water? I live in Atlanta area, should I put the plant outside or can it stay inside? Thank you sooo much in advance for response.

  • 10 years ago

    WE GET IT!!!!!!!!!!!!!!!!!!

  • 10 years ago
    last modified: 10 years ago

    If you put it in the gritty mix, you need to fully repot and remove ALL of the old soil.

    Moving it outside will greatly help it fill out. You must acclimate to full sun or you'll burn a lot of leaves. However, if that happens, new ones will grow back that can handle full sun so it doesn't matter much.

    I'd also prune it back to help with back budding.

    Got mine at lowes a little over a year ago for $20. It was 4' tall and is now over 7'. Mainly due to being outside last summer. That said, in the 4 years you've had it, your tree should have grown a lot more and isn't growing due to the cultural conditions you're providing. No offense.

  • 10 years ago

    Makes sense Al. So if I wanted to air layer a tree about 3/4" in diameter and the clone would be about 2-3' tall, do I just make a slice above a leaf node and below a leaf node and peel that off and wrap it? I guess my question is where to remove the cambium layer and how wide of a layer to remove.

  • 10 years ago

    You needn't remove bark in a specific place if propagation is your only goal, but the ht of the bark removed should be equal to 1.5X the diameter of the branch/trunk at that point. For Ficus b, you should ring the bark entirely.


    A couple of other ways to layer below




    The bark would be ringed or there would be a tourniquet around the branch in the last 2 pictures.


    Al

  • 10 years ago

    It's for a Ficus Elastica. So where exactly so I make the rings? Above and below a leaf node, or both directly below? Can I just wrap it in some highly composted pine bark? I don't have any peat on hand, but the composted pine fines seem like they'd stay moist for quite a while.

  • 10 years ago

    Jow,

    can you make a new thread in this section of the forum about the issues you'd like to resolve? We can talk about the ficus and also your spider mite issue with your Schefflera.

    Let's try not to hijack this thread so things don't get confusing.

  • 10 years ago
    last modified: 10 years ago

    Use the flap method for elastica (second picture above) & slide toothpicks under the flaps to hold them open. How did we get to elastica from mistletoe fig? You should use a well-aerated soil and a container like I showed with the twig through it but with a hole through the bottom if required, or use sphagnum moss as your medium for air layers.

    Al

  • 10 years ago

    Thanks Al. Could you give me some specifics, such as: Location of flaps in relation to the nodes, length of flaps (still 1.5X diameter of plant?), depth of flap cuts. Thanks for the help.

  • 10 years ago

    It doesn't matter where you cut the flaps - cut them anywhere along an internode. If you look closely at the picture above, you can see I cut through the phloem, the xylem, and took a little sapwood when I made the cuts. After you make the cuts, stick a piece of toothpick or a small pebble under the flap to hold it open. Cut them long enough so you have a flap. The ones in the picture are about 1" long. The number of flaps depends on the diameter of the branch/stem you're layering.


    Al

  • 10 years ago

    Ok so 3-4 flaps would be good for a 3/4" diameter tree? Can I just use some gritty mix as the medium?

  • 10 years ago

    4 flaps for a 4/4" tree, and the gritty mix should be great if you're using the pot method and don't mind waiting a couple of weeks longer, otherwise get some sphagnum moss and do the more traditional layer with the moss wrapped in plastic and the whole layer covered by aluminum foil.

    Al

  • 10 years ago

    So, I had it done before you responded and only used 3 flaps, but the plant is closer to 5/8 so I think it will work. Does it need to be air tight or can I leave it like this? Let me know what you think and as always thanks for the help, it is very much appreciated.

  • 10 years ago

    The moss should be damp - not wet, so there should be provision for drainage from the bottom of the layering capsule. Traditionally, they are sealed at the top - like a sausage, with only a small opening to add a little water when necessary. Maybe you could fashion a cover from aluminum foil, which would block light and slow evaporation. Use a spritzer to remoisten the sphagnum moss & don't over-wet it.

    Al

  • 10 years ago

    I used gritty mix for the medium and it can drain from the bottom. I can put a piece of foil around it. Hope I did it right!

  • 10 years ago
    last modified: 10 years ago

    That should work - didn't realize it wasn't moss - didn't click the pic to enlarge. DO use something to block the light, though.

    Al

Sponsored
High Point Cabinets
Average rating: 5 out of 5 stars21 Reviews
Columbus' Experienced Custom Cabinet Builder | 4x Best of Houzz Winner