Software
Houzz Logo Print
sbetterton1

1970's Nightmare Underpadding!

9 years ago

So after a few months of pinching our pennies the wife and I have just purchased some awesome laminate flooring for the main level of our house. Because I have installed laminate before and consider myself somewhat handy I decided that we would install it ourselves. There's a bit of a problem though.. Ok thats an understatement, there is a HUUUUGEE problem! and it involves what can only be describe as this awful hard clay/rubber under padding that has bonded itself to our floorboards. Clearly whoever lived in our house before us didn't want to attempt this battle because they placed a new under padding over top of this stuff before putting in a new carpet.

Now I've honestly spent a good 3 hours or so scouring the internet for any advice I can find on how I can defeat this monster but haven't found anything all that promising.

Here's what I'm wondering. Over the past few days we have been trying to scrape all of this stuff off the floor. In some areas it comes up without much of a problem at all, but in other areas it grips the floor like you wouldn't believe. No matter how much you scrape at it, it just wont budge. Here is my question: If I manage to scrape most of it off the floor to the point that its only a millimeter thick would it be safe to assume that this wouldn't have a negative impact on my laminate flooring? I could even use a belt sander to make it a little bit flatter if needed.


We've honestly spent about 10 hours trying to remove this garbage from a 10sq foot area and we still haven't gotten rid of all of the orange substance. It's very flat and looks a lot like someone has put cast material all over the floor boards. We aren't trying to take the easy way out but we're pretty much at our wits end with this stuff and could really use some assistance on the matter.


Please if you have ever dealt with this before I am begging you for some answers for I fear this job will be the death of me.


P.S. whoever invented this 1970's underpad of hell is an awful individual!

Comments (17)

  • 9 years ago

    Is there white thread running through it?

  • 9 years ago

    Only on the top. We have scraped all of that out to leave just an orange clay like material. Thanks for the reply Jocelyn! :)

  • 9 years ago

    Photos, please! :)

  • 9 years ago

    Had that stuff in parts of my house, but it had fortunately just gone to crumbs. There were thousands of staples holding it to the plywood that I had to remove. I am guessing yours was glued down, and not stapled? I have removed glue from small areas with furniture paint stripper, would be a long stinky process.

  • 9 years ago

    I'm at work right now but I promise I will post a photo when I get home.

  • 9 years ago

    All


    right just got home and took a picture of this mess.

  • 9 years ago
    I have not removed that exact material before but did remove some old laminate type tiles from a large bedroom. We rented a floor scraper from Home Depot for a day. It works really well if you can get an edge pulled up for the blade to get under. The equipment is a little smaller than a floor buffer and is pretty easy to use. Hope that helps!
  • 9 years ago

    Maybe you could use one of these?

    Steve thanked Sammy
  • 9 years ago

    If it comes down to it I might try something like that but I think first I want to try a belt sander and see how that works. I guess my real question that I was hoping to get an answer about was whether I would be ok with leaving some of the orange colour on the wood. Like will it be ok if I can sand it down to a very thin layer and just put the new underpad/laminate over it. I understand the importance of having a level floor but I don't think a millimeter would be at all noticeable.

  • 9 years ago
    We removed carpet from a small bedroom to refinish the hard wood and it took weeks to remove the glue! Ours didn't look like that, it was basically black, but I know your pain. We used a razor tool from homedepot, and shovels. It was awful.
    Steve thanked sharayak
  • 9 years ago

    Ya that sounds awful. I mean ours is horrible but the only plus side to it is that it isn't really a glue but more of a really hard clay like substance. For that reason I feel like a belt sander could actually do the trick and I happen to own one from a previous deck refinish job I did last summer. That was a bit of a nightmare job too, lol.. Oh the splendors of home ownership.... lol

  • 9 years ago

    bump

  • 9 years ago

    If you take a belt sander to that, please, please wear a good quality respirator while doing it. You do not want to breath that stuff into your lungs!

    Steve thanked ryann_j_macluskie
  • 9 years ago

    I do have a respirator but just out of curiosity why do you say this? Is it toxic? I hope there's no asbestos in it..?

  • 9 years ago
    last modified: 9 years ago

    I would not think that there is anything toxic in it, but sanding will break it down small enough to make particles become airborne. Like you said, it is some kind of rubbery material. You don't want to inhale it. I know several DIYers from the older generation who are now having COPD and asthma issues from years of not wearing respirators while woodworking or sanding and inhaling fine wood particles.

    Something like this is worth the expense

    http://www.homedepot.com/p/3M-Medium-House-Hold-Multi-Purpose-Respirator-65021HA1-C/202080143

    Steve thanked ryann_j_macluskie
  • 9 years ago

    Hey Ryan, I actually have one of those that I use to paint with so I should be good to go. And you raise a really good point. Just because it's not considered highly toxic doesn't mean it should be in your lungs.

    Appreciate the feedback :)