Software
Houzz Logo Print
hzdeleted_48976844

Uneven filler strips

8 years ago

I just had a contractor place a new Kubebath vanity in gray oak in my recessed bathroom. He did tell me that the filler strips would not look good because the recess space does not have perfectly parallel dimensions. However, the end product does look very strange to me. Are there ways my contractor could have made the filler strips fit better, i.e. scribe more or add extra pieces of wood? Or should I remove the filler strips after all?




Before any filler strips




Finished front view- contractor could not find any closer color for filler strips





The (my) right side is fine, but the left filler strip is not flush with counter top. We have had to put extra caulking in the back due to another gap between the vanity and the back wall.




Also on the left side, there is a gap large enough to fit a paper folder. Can an extra piece of wood be added to close that gap?

Comments (14)

  • PRO
    8 years ago

    He did an excellent job. These are cabinets, not the Space Shuttle. "Gap large enough to fit a paper folder"? Seriously?


    Pay him and be grateful, please.

    User thanked Joseph Corlett, LLC
  • 8 years ago

    Already did. Just trying to get some advice here

  • 8 years ago

    I'd take the filler strips out.


    User thanked tdemonti
  • PRO
    8 years ago

    I think it looks better without the filler strips too; remove them.

    User thanked Skippack Tile & Stone
  • 8 years ago
    I think he did a great job, but I prefer furniture-like vanities without the filler strips.
    User thanked Elle
  • PRO
    8 years ago

    He did a good job but this is a furniture piece vanity so it just looks odd with the fillers. It's trying to be a built-in with those fillers but it's not. My vote is no fillers!

    User thanked Sina Sadeddin Architectural Design
  • PRO
    8 years ago
    If you were doing a custom top I would have used the fillers but recessed them an inch or two so they were less visible. Since you aren’t using a custom top you should have skipped the fillers.
    User thanked Ellsworth Design Build
  • PRO
    8 years ago

    I would leave the filler strips. The spaces between the vanity and the wall are so small that leaving them open is going to both look weird and will be a problem if you drop something or want to clean the area (which will be a magnet for dust). A furniture-type vanity looks great when it is featured in a larger space, not when it is plunked into a space that is just a wee bit too large, as this one is.

    User thanked Diana Bier Interiors, LLC
  • 8 years ago
    last modified: 8 years ago

    better without the filler strips. a swiffer would fit down the sides to dust. BUT you will not be able to repaint without taking out the vanity.

    User thanked Judy Mishkin
  • 8 years ago

    The design is the issue, not the install. You don’t build in furniture pieces without the pieces being designed and built especially for that. That cabinet was not designed to be anything other than freestanding. And it is too large for the space. You need 4”-6” of open space on either side as a minimum.

    Do a different vanity entirely. That doesn’t work.

    User thanked User
  • PRO
    8 years ago

    I agree with Spphie the wrong piece for that space and IMO by the time you pay for the vanity, the install and now filler strips you could probably done custom, you have walls that are not plumb that is not the fault of the installer unless he did all the work in the space.

    User thanked Patricia Colwell Consulting
  • 8 years ago

    Thank you all for the advice! In retrospect, a smaller or a custom-made vanity would have worked better. Unfortunately replacing the vanity is not an option due to cost.

  • 8 years ago

    Let it be for a little minute, it looks good on my monitor.

    User thanked smileythecat
Sponsored
Hope Restoration & General Contracting
Average rating: 4.7 out of 5 stars35 Reviews
Columbus Design-Build, Kitchen & Bath Remodeling, Historic Renovations