Software
Houzz Logo Print
cline6771

Shutter hinges with aluminum clad windows?

5 years ago

New construction: Brick house (to be painted) - Pella Architectural 6 over 6 double hung windows with a 3 1/2" brick mold - simulated divided lights - wide muntins - a traditional, historical look.

I really would like to have shutter dogs and hinges on my shutters (but they do NOT need to be operable). I think the shutter dogs can be installed to the brick without any problem but I don't know how hinges can be attached to the windows because the window is aluminum clad so I assume the brick mold is also. is that right? And the hinge would have to be attached to the brick mold? Could hinges somehow be attached to the brick instead of to the brick mold? How would that work? I'm confused about exactly how the brick mold looks and where it sits and where the hinge would need to be attached.

Comments (10)

  • 5 years ago

    Please provide a few photos.

  • PRO
    5 years ago
    last modified: 5 years ago


    It is a question for your BUILDER


    "

    Exterior Shutter Hinges

    "Historic shutters were mounted on hinges. There are two parts to a shutter hinge. One part is attached to the house and the other part is attached to the shutter. The part of the shutter hinge that is attached to the house contains a Pintle – a pivot point for the shutter hinge to rest on. This part of the hinge can either be mounted to the house on the face of the window casing OR on the inside edge (jamb) of the window. Each of the two mounting types provides a different appearance.

    There are many types and sizes of shutter hinges you can use. A lot depends on your window and how much space you have to mount the hinge. These details and customizations you should discuss with the shutter manufacturer. Here, on OldHouseGuy.com, you will learn what you need to know to get the proper look.

    If you think your house originally had shutters, you can check to see where the original hinges were mounted by looking for “ghost marks”. Even after years of painting, you should still be able to see these marks. You may even see them in both places (edge and face) – this means your shutters and/or hinges were replaced. Most likely, old face-mounted strap hinges were replaced in the late 19th century with newer hinges mounted on the inside edge."





  • PRO
    5 years ago

    Only your builder knows how the brick mould is made- on my house they were applied after the windows were installed.

    Yes you can hinge the shutters off the brick but screws set that close to the edge of bricks tends to make them crack.

  • PRO
    5 years ago

    If you purchased the windows with Pella's factory brickmould it's most likely aluminum. If it was field applied it could be aluminum, wood, composite or PVC.


    The shutter dogs alone will suggest the shutters are operable to most people. I suggest you install them on a pair of shutters and evaluate whether you need the hinges. If you do, fastening them to the 3 1/2" brickmould will be an easier task than attaching them to most vinyl shutters.

  • 5 years ago
    last modified: 5 years ago

    The trim from Pella is extruded aluminum and should be attached at the factory.

    I assume your windows are aluminum clad wood double-hungs from the Pella Architect Series and the trim is Pella's 3 1/2" Brickmould shown below and is slightly recessed in the brick openings rather than lapping over the face of the brick.



    The simulated "brickmould" is actually the outermost band and the wide flat part simulates flat casing trim more commonly found on a wood clad house. I assume the window and trim will be recessed an inch or so back from the face of the brick instead of overlapping the brick. Such a wide trim in a brick opening is unusual.

    If the shutters were mounted on the flat part of the moulding they would not be able to lie flat against the brick unless the hardware offset was unusually large as shown below.



    The other choice would be to mount the shutters to the brick in the convential manner so that the closed shutters would fill the brick opening as shown HERE and below.



    In either case, the mounting screws should be installed very carefully.

  • 5 years ago
    last modified: 5 years ago

    For a traditional brick house, I would have expected the window trim to be Pella's Standard Brickmould.







  • PRO
    5 years ago

    NO pictures no help but what the hell is the point of paying for brick if you are going to paint it . We need a lot mor einfo and pictures.

  • PRO
    5 years ago

    @RES2,

    Some traditional designs benefit from the wider brickmould. The Wythe House in Williamsburg, VA is an example:




  • 5 years ago
    last modified: 5 years ago

    I did a gut rehab of ths one. It too had no shutters.

    If you're going to cover up the wide casing trim with shutters why bother to install wide trim?

    But it does make it easier to replace the windows.


  • 5 years ago

    I appreciate those of you who provided helpful information - thank you so much. I'm learning and trying to be sure I understand something which is unfamiliar to me. I do not have pictures because the house is not under construction yet. We are in the process of ordering windows and I want to be sure I will have the look I want, which is historical and traditional. I thought the wider, recessed brick mould would give me that look, and I do want shutters and I was trying to figure out if the hinges hardware could be applied. I will talk to my builder and the window supplier about this but the information above has helped me understand. (By the way, as to painted brick, I really believe that's a personal preference. I live in "brick country" and the look of a regular brick house is not that distinctive. YMMV which is fine.)