Corner Drapery Rod question

2 years ago

last modified: 2 years ago

I asked this q in a sunroom post but no one noticed it or else thought it was too boring. : )

I have bamboo blinds on order, and 4 panels on order. The panels will be hung almost to the ceiling (they are 9' long and that is my ceiling height), and over the blinds (see pic one, below).

In the corner, I will have two panels; there is virtually no wall space in the corner. Similar to picture two, below.

Function: None. These are decorative. I do not anticipate opening or closing the curtains; prob not the blinds either if my experience so far is indicative! The curtains are unlined and appear lightweight. They have dual hanging options: rod pocket (bunched) or back tabs (pleated).

My questions;

I assume I have to get a rod that goes around a corner? Is there a term for that when I search?

The blinds person said, when I asked, that a rod that protruded 6" should be fine. That seems like a lot, so I asked a follow up question and he said: "It is probably 2-3 inches with the stack up high. The stack will be coming forward if it is up. You just want to make sure you are in front of it. You could always look into purchasing adjustable extension brackets for the rod if needed. "

WWYD and where would you look. I want something simple. Also, pocket or tabs?

Featured Answer

deegw

2 years ago

last modified: 2 years ago

DH and I DIY a lot of things and it took me forever to realize that hanging panels is complicated and requires a lot of nit-picky decisions. DH would just throw up a rod and I'd get the length right but wonder why the panels never looked quite right. For my next house, I am leaving the drapery hanging to the professionals!

Sort by:Oldest

Comments (11)

deegw
2 years ago
The stacking is a puzzle, especially if the hanging hardware gets in the way.

In one of our houses, I had an odd bedroom window configuration - the windows on one wall were crammed to the corners and the other wall had an angled bay-type bump out. I used French rods on all the windows. They solved the stacking problem and the tight corner issue.

Rod pocket often looks messy to me but I have an issue with symmetry so it might be a me problem.
mtnrdredux_gw
Original Author
2 years ago
Had to look them up, but I like French rods. Another dumb question. The long wall is about 15" IIRC; I assume you can just peice rods together?
Related Professionals
Waycross Furniture & Accessories · Dayton Furniture & Accessories · Johnson City Furniture & Accessories · Cedar Rapids Furniture & Accessories · Escanaba Furniture & Accessories · Durango Furniture & Accessories · Dubuque Interior Designers & Decorators · Sierra Vista Interior Designers & Decorators · Billings Interior Designers & Decorators · La Grande Interior Designers & Decorators · Casper Interior Designers & Decorators · Middlesboro Architects & Building Designers · Owensboro Architects & Building Designers · Redding Architects & Building Designers · Sterling Architects & Building Designers
jojoco
2 years ago
try "drapery pivot corner bracket".

I love the wrap around look.
deegw
2 years ago
Mtn, you would likely have one long rod with support hardware on the long wall, not sure if you can get one that long but it should be easy to find out.

I did want to point out that your inspiration photos have panels hung with rings. That's my favorite look but not sure if it will look good or make sense for your inexpensive panels.
mtnrdredux_gw
Original Author
2 years ago
Dee, I am thinking that I should do what the vendor shows. Am I right that they have the rod through the pocket?

Also, can i find decent rods at Lowe's, etc.?
deegw
2 years ago
I think that's the back tab, rod pocket usually looks more bunchy on top.
mtnrdredux_gw thanked deegw
Tina Marie
2 years ago
I would do the back tabs, or you can also iron the heading flat and use rings. Using rings might make the panels too long though. I also like the wrap around look.
mtnrdredux_gw thanked Tina Marie
Funkyart
2 years ago
I have a similar challenge in my breakfast room-- the there is little space in the corner for the hardware. I opted to use two rods but will upgrade to the corner rod soon. It looks soooo much better!

At the time PB had them for sale but I wanted to try the cheaper option first because the rods don't actually show much ... but I regretted the decision almost immediately.

I did consider the french rods as the time-- but I couldnt find any that would work well with my tight corner. I do like them a lot!

Both Lowes and HD have upped their offerings in the last few years-- it wouldnt surprise me if they had decent options but I don't know from experience.
mtnrdredux_gw thanked Funkyart
ratherbesewing
2 years ago
You need a corner piece that joins the 2 rods. Many choices on the Big A (wont allow me to save a photo ). Google corner drapery rods and you get lots of options (from finish to rod diameter). Most drapery brackets are adjustable so you can ensure clearance from your blinds. In addition, Dee is correct —the printed drapes are back tab.
mtnrdredux_gw thanked ratherbesewing
mtnrdredux_gw
Original Author
2 years ago
Ballard had all the requisite pieces from the same line; other purveryors did not have the connectors. All told $457 in hardware though; ouch.