Software
Houzz Logo Print
vmckague_gw

'Another' Earthtainer question

17 years ago

I'm new at building earthtainers and have the first one finished. It came out really good and am planing to build more of them. My question is has anyone came up with a good design for using the lid cutout for the insert instead of using the bottom of another container? Maybe a few pictures showing what you use to hold the lid off of the bottom and to support the weight of the soil. Also how to keep the sides for bulging out from the pressure of the soil mix. If I could use the lid cutout it would save a lot of money and I like getting the most product for the money. Thanks in advance.

Comments (14)

  • 17 years ago

    vm,

    If you are growing tomatoes and want the rigid cage support system, then forget trying to improvise with using the lid for the aeration bench. Others have come up with alternative bench solutions - - but none will provide the strength to support two tomato cages attached to the main container.

    Raybo

  • 17 years ago

    Thanks Raybo for the info. I'm on the way to get supplies to make 3 more earthtainers. One quick question, How did you come up with the name earthtainers?

  • 17 years ago

    vm,

    I created the name "EarthTainer" as a contraction of "Earth" and "Container". It just sounded kind of accurate as to its purpose.

    Raybo

  • 17 years ago

    I am building/built the Earthtainers using the lid cutout.

    I cut drinking water safe 1.5 inch PVC pipe to the height of the basket (4 inches). For the 18 gallon ones I used 4 on each of the four corners. I may need to use more for the 31 gallon. I drilled holes in the PVC to allow water to freely move through it and some on the top so that I can fasten it to the lid cutout. I fastened the PVC pipe to the lid cutout using zip ties (exactly how the basket is attached).

    That is my plan and what I have so far. I think that should work but if I find that I need more support I am sure I can either use some toggle bolts or something else.

    I found the key to using the lid to be to flip the lid over and cut the exact shape maximizing the amount of plastic. Mine fits very snug. I used an exacto knife to get a perfect cut.

  • 17 years ago

    buck,

    Are you attaching the tomato cage system externally, (or maybe growing something else that does not need a cage)?

    Raybo

  • 17 years ago

    For now, I just plan on building something externally ($$ factor).

    Just thinking outloud, I suppose if I were to build the cage system into the lid cutout I could use that as an additional support sytem (would provide very little support but wouldn't weigh it down either). Whether by using tomato cages or concrete reinforced wire (may be too heavy), you could make sure you had only the vertical metal bars poking through holes drilled into the the lid (clip off any vertical bars that were below 4 inches) and fasten it below the lid cutout with a ?wire rope clip?.

    Again, that is me completely thinking out loud but it might be a start.

  • 17 years ago

    I just finished my first ET and started to fill it with potting mix. I had a 55 qt of MG mix and it didn't fill it! It looks like it will probably take another 10 qts at least. Can I use this again next year and if so should I mix a little fresh mix in with it? I'm going to make 3 more boxes this weekend and now have to figure out how to tell the wife I need 4 more bags of potting mix. LOL She can't understand why I don't just use the garden like I have for the past 25+ years. It's a good thing Sam's has them for 11 dollars a bag. Thanks for any advice in advance.
    Raybo, I made a donation to feed the children as I went by your videos and think it's only right to do so.

  • 17 years ago

    vm,

    Are you using this potting mix:

    {{gwi:17662}}

    It comes in 2.5 cu. ft. bags. It takes approx 3.3 cu.ft. to fill the new EarthTainer II due to the larger capacity now above the aeration bench. So 3 of these bags (in the picture) will fill 2 'Tainers.

    Instructions for "recharging" the potting mix next season should be at near the end of the Construction Guide. Basically, I try to extract 1 cu. ft. of the old potting mix around the root ball, then mix in 1 cu. ft. of new potting mix when planting again in the Spring. I figure 3 seasons total, then I will reuse the old mix somewhere else in the yard and start season 4 with all new mix.

    {{gwi:16498}}

    Raybo

    p.s. A big "THANKS" for remembering to make a donation to the Feed The Children Organization. They need all the help they can get in these difficult times.

  • 17 years ago

    I drill pairs of holes on opposite sides of the container (3 on the long sides, 2 on the short) at the desired height of the bottom of the soil and then I stretch 16 ga copper wire between the pairs securing it on the outside of the container by forming a large coil. On top of this one can put the cut out from the top of the container, cut to fit tightly in the space with plenty of small holes drilled in it for air and drainage, or a piece of plastic flourescent light grating cut to fit then covered with some sort of netting (window screen fabric) to hold the soil, or (my favorite) use two 10 gal Rubbermaid Roughneck containers and just set the second one, right side up, inside the first, on top of the wire after drilling the appropriate holes in its bottom. If any of these ideas interest you I can post photos of my empty containers--- after I find out how to post photos.

  • 17 years ago

    new_city_girl, I like your idea with the copper wire.

    I was considering that for a secondary support for the lid in the 31 gallon container if the 4 pvc pipes weren't enough to hold up the lid entirely, but never thought of it without another type of support. I'm curious if it comprimises the integrity of the outside of the container (the wire holding up all that weight in dirt) by pulling down on the outside of the container walls. How long have you used this method? I'm curious about the life expectancy of the containers.

  • 17 years ago

    I don't go larger than 18 gals so the weight isn't so much, and I left out that I cover the holes in the containers with metal grommets before stringing the wire to keep it from cutting through the plastic of the container. I have pictures but I don't know how to post them. Can anyone help? If not, you can see them at http://www.flickr.com/photos/drobberbaron/

  • 17 years ago

    Here are some photos of a couple of my containers. I haven't used these techniques with containers larger than 18 gallons, so I don't know if either would work with 25 or 31 gal containers, but it might give someone another idea.

    A double 10 gal container (I include this because it seems like a better way to use 2 containers together):

    outside, assembled
    {{gwi:17663}}

    inside top container
    {{gwi:17665}}

    inside bottom container showing wire support
    {{gwi:17667}}

    alternate wire setup
    {{gwi:17668}}

    underside of top container
    {{gwi:17669}}

    18 gal container
    {{gwi:17670}}

    shelf in 18 gal container made from flourescent light grid cover, resting on wire supports. holes haven't been cut for "wicking cups" yet
    {{gwi:17671}}

    lid being cut to form shelf which could sit on top of wire supports
    {{gwi:17673}}

    I haven't completed one with a lid shelf yet, but, as with the grid shelf, I intend to line the portion of the container which will hold potting mix with window screen cloth.

  • 17 years ago

    http://www.homegrownevolution.com/

    Go to this web site, scroll down on right side to self containers and click on it. I use this method to support the lid on the 18 gal tote, it works fine and it will carry a lot of weight.

    Bill B

  • 17 years ago

    The site posted above by Billb_veggies shows the "bible" of SWC. I've used the 4" drain pipe, and found that to be great. I do the double tub, also, but economically, using the cover works very well.