Software
Houzz Logo Print
wvhagan

Oil level in lawnmower

17 years ago

I have a Lawnboy with a basic Tecumseh engine. Last year I accidently overfilled the oil. It hasn't seemed to cause any problems. In an unpressurized system, can accidentally overfilling the oil cause any harm? As long as the mower has enough oil, and your mower isn't smoking, it seems that a little extra oil shouldn't harm anything.

Comments (12)

  • 17 years ago

    That depends on what you mean by "a little extra oil". If it's enough to cause foaming of the oil then it can cause harm. If your mower seems to be running alright now, and has the proper level of oil in it, then chances are that it's ok. Watch the oil level and run it.

  • 17 years ago

    With the mower level and the oil hot, remove the dipstick and wipe it dry. Reinsert the dipstick and screw the cap down. Remove it again to check oil level. Tip the mower up to pour out excess oil, then re-check level. I wouldn't deliberately run it with too much or too little oil.

    Note: on Honda GCV and GSV engines, do not screw the cap down when checking the oil. Crazy, I know, but that's the deal.

  • 17 years ago

    Orangedotfever, could you tell me more about foaming of the oil? I've heard the term, but am not too clear on what causes it and how it harms the engine. I use 75% thirty weight oil and 25% Lucas oil stabilizer. "A little bit extra oil" is imprecise. Change that to 1/3 way up the dipstick. That is probably more than some might call "a little bit extra." I wouldn't and didn't INTENTIONALLY put too much oil in the mower, but last year after I had done it, I thought that as long as the thing has the lubrication it needs, what harm could it do? Usually I change the oil in my mowers every spring.

  • 17 years ago

    When you have too much oil in the crankcase the moving parts that don't normally touch the oil can dip down into the now high level oil and whip up a foam of air bubbles. This foam will inhibit lubricating the engine parts be it a splash type lube system or a pressure type. Air bubbles don't pump well or they keep the liquid oil from being splashed where it needs to go.

  • 17 years ago

    Thanks for the information!

  • 17 years ago

    orangedotfever, Your description of oil foaming from overfilling is complete fiction. Nothing even close to that happens. Modern motor oils do not foam. If they did engines wouldn't last 5 minutes. As far as the oil level affecting the way the oil is splashed....it does not matter. The oil is being thrashed around in there like it's in an F-5 tornado anyway.
    The reason manufacturers warn against overfilling on vertical shaft designs is to prevent oil from seeping past the piston and causing a hydraulic lock in the combustion chamber. Also overfilling can cause excessive oil consumption if it gets into the crankcase vent system. Excessive overfilling can cause overheating.

  • 17 years ago

    Old wives tales die hard I guess. My 2 strokes don't foam anyway.

  • 17 years ago

    How much of an overfill? 2 ounces is one thing but 20 is way overfilled. The crankcase capacity is quite small, usually around 2/3 quart or so.

  • 17 years ago

    ....and more food for thought: Lucas Oil Stabilizer was notorious for causing oil foaming. We used to run into mystery missfire codes on electronic injection diesels and after much head scratching a bright tech figured out the common denominator was "LOS". Eventually there was a service bulletin on it.

    Maybe the new stuff is better/reformulated.

  • 17 years ago

    25% Lucas is way too much anyway. If I were going to use it, I would use the synthetic 'new car' formula at only 1 oz to an oil change in a mower. You're using as much in 20 oz of oil as I use in 5 qts in car engines with 75,000 miles - 4 oz. I know they advise using that much but I just can't see it. What the 4 oz has done for me is provide quieter start-ups, which is exactly why I used it. I would never use a whole qt in an engine in good condition. These engines are 4-cam, 24-valve V6s (GM L81) that have a history of valve train noise and problems. Without the LOS I was getting some tappet noise sometimes on cold starts. With the LOS it's been fine. 4 or 5 oz in a lawn mower is definitely overkill.

  • 17 years ago

    I received an old mower from a man, who said he had added oil to the top of the dip-stick tube! He asked if that was too much oil!
    Duhhh!

  • 17 years ago

    "I use 75% thirty weight oil and 25% Lucas oil stabilizer. "

    What properties of modern engine oil are so unstable that they require an additive. Or asked another way what characteristics do you think the engineers at Mobil, Shell, etc., forgot in their motor oil formulation?

Sponsored
Peabody Landscape Group
Average rating: 3.5 out of 5 stars8 Reviews
Franklin County's Reliable Landscape Design & Contracting