Software
Houzz Logo Print
quintus_gw

duraforce tip

19 years ago

I stopped by my local mower shop to do some shopping for the upcoming season. I started talking with the senior tech about opening season problems and repairs. We got around to talking about LB's and I asked him what the most prevalent problem was with the duraforce. He said definitely the carburetor and within the carb. the float and needle seat. He said the cork floats become fuel logged, then lose bouancy and fail to put enough pressure on the needle to shut off fuel. His solution? Install a fuel shutoff, then use it shut down the mower after each use. That way the float is only bathed in gasoline while the machine is being used.

Just a tip for those who are interested.

Comments (13)

  • 19 years ago

    Float logging has been a possible problem on all Lawn Boys that used the cork float. Some floats will last a long time and not become fuel logged, some just a little and some a lot. It is often difficult to tell if a cork float is partially fuel logged without weighing it and comparing the weight with a new dry float. And yes any fuel logging is going to produce less pressure on the fuel inlet needle meaning a less than ideal seal.
    Fuel and oil will be absorbed into the cork if there is a break in the coating covering the float. Where the brass prongs enter the cork can be another entry point. I have found that recoating a new float (or dry used one) with a product called U.S standard tank sealer adds very little weight to the float and gives extra insurance against logging.

  • 19 years ago

    "That way the float is only bathed in gasoline while the machine is being used."

    I agree with the fuel shutoff valve but not with the statement above. Even if you shut off the gas, run the engine until it quits, there is still gas in the carb bowl unless you take it off and dump it each time.

    Cork carb floats were used in the days of the "good ole Lawn Boys" with very little problem. I have 40 year old LBs with this style float but perhaps they are better made.

    Walt Conner

  • 19 years ago

    I see another post that the cork floats were a problem. I specialized in LB repair for a number of years and saw very little problem with this.

    However, with the wide spread use of Ethanol, this may be an increasing problem with the Alcohol in the fuel. I try not to use Ethanol in anything but that is all the station I normally trade at, where I have a discount card, sells. I drive a little farther and pay a little more for gasoline without Alcohol for all our small engines.

    Save all the "Green" posts until you know yourself positively the amount of pollution resulting from the production of Ethanol.

    From a long line of farmers whose farm income from corn production has doubled as a result of Ethanol.

    Walt Conner

  • 19 years ago

    Walt-

    I don't mean to disparge your knowledge and experience, however, I ran the following test.

    I have an old Toro whirlwind with a Tec. TVS-840 2 stroke.
    The carb. has a bowl drain on the bottom. I started the engine then turned the fuel off till the engine quit. I pressed the drain button, only three or four drops of fuel came out. Clearly the bowl had been mostly drained.

    Most small engine manuals recommend running an engine till fuel is exhausted in preparation for storage. This ensures that MOST of the fuel is used up. This prevents gumming and clogs when the engine is again started.

  • 19 years ago

    The discussion was about fuel logged float, not long term storage. I admit I do not have much experience with LBs, only about 40 years. While some did have the bowl drain, most do not and they have gotten so tight that they do not put a fuel shut off valve on them even now. The bowl drains were handy for removing water & crap, until they started leaking. They were not put there to keep the float from becoming fuel logged.

    Walt Conner

  • 19 years ago

    "That way the float is only bathed in gasoline while the machine is being used."
    I agree with the fuel shutoff valve but not with the statement above. Even if you shut off the gas, run the engine until it quits, there is still gas in the carb bowl unless you take it off and dump it each time.


    Shutting fuel off and allowing the engine to run until it quits does indeed drain the float bowl with the exception of a few drops at the bottom of the bowl. I verified this by test. During the long periods between mowing sessions, (perhaps weeks) the float is not sitting in gasoline. Therefore, the time exposure of the float to gasoline is drastically reduced. This prevents the slow absorption of gasoline by the float and consequent gas logging. The tech was right. Think about it.

  • 19 years ago

    not a very good idea to starve your two stroke of gas.
    It creates a lean condition and can burn up your engine.

    Same amount of air is coming in, but you've drastically reduced the amount of fuel going through the engine. lean seizures can happen because of this, especially if you have a leaky petcock that does not seal fully when vacuum is put on it.

  • 19 years ago

    Hello all.

    Hi slag, rollerzeke is not an expert on this Duraforce tip. But I think that you have a very good point.

    Good day.

  • 19 years ago

    Is it possible to attach a small hose with valve on the bowl? They are plastic, so maybe this is doable? Then you can drain the bowl after each use. Room is tight, but maybe it will work? Could you tap into the plastic bowl bottom with a small right angle brass fitting..attach some fuel line with a valve? You would need a valve on the tank too.

  • 19 years ago

    "not a very good idea to starve your two stroke of gas.
    It creates a lean condition and can burn up your engine.
    Same amount of air is coming in, but you've drastically reduced the amount of fuel going through the engine. lean seizures can happen because of this, especially if you have a leaky petcock that does not seal fully when vacuum is put on it."

    The carburetor bowl is a resevoir for fuel, the level of which is controlled by the float and needle assembly. As fuel is drawn into the engine, created by the negative pressure in the venturi of the carb., fuel level in the float bowl (carburetor bowl) drops. When the fuel level drops the float drops and the attached needle opens the fuel inlet and more gasoline enters the float bowl. The riseing fuel level raises the float and needle, shutting off the fuel. As the engine runs the process is continuous: fuel used, float drops, more fuel enters carb. bowl. If you cut off the fuel supply via shutoff, fuel is constantly drawn from the resevoir(float bowl), which is now NOT BEING replenished. The engine runs until there is no longer any fuel left in the carb. float bowl. At most, there are a few drops of gas left in the bottom of the bowl which could not be pulled up thru the jets. However, the jets and other carburetor circuits are clear of fuel. This prevents gumming from fuel evaporation during long storage.

    How does this procedure cause a lean condition? Fuel with lubricant(two stroke)is being supplied until the engine quits. MAYBE, one or two seconds before the engine dies it does lean out, but I doubt this will cause any damage. ANYWAY, EVERY MANUFACTURER I know recommends operating gasoline engines(two and four stroke)till fuel is exhausted in preperation for storage, just for the reason cited above.

  • 19 years ago

    In this day of high tech materials and manufacturing techniques it's amazing to me that a company still opted to use a cork float. Lawn-Boy mowers should have a float designed to last as long as the mower probably will. Once again we have "bean counters" and accountants to thank for the misery that float will cause a few years down the line. I hope the extra penny profit was worth it to the corporate moron who made the decision to continue cork use. He probably doesn't even work for Lawn-Boy anymore. I hope his toilet has a saturated cork float and runs on and on this weekend. Ha. Whatever....

  • 19 years ago

    I always wondered about Lawn Boy's use of a cork float. It might have been because of the outboard motor connection with OMC,boating and fishing (remember cork bobbers and fishing pole handles). Years ago many carburetors from automobiles to aircraft used cork floats, most of them switched to brass, plastic or composite but Lawn Boy stayed with cork for a long time. The cork float actually works quite well as long as it doesn't absorb any fuel. The key is in the coating covering the cork. Over the years Lawn Boy tried a couple of different coating formulas. Many floats were ruined when owners used certain additives in the fuel that softened the coating or dissolved it. I think that a metal float would have probably been better, although metal floats sometimes leak and fill up with fuel themselves. I like the cork float, its another one of the things that set a Lawn Boy apart from the rest, just like the two cycle engine.

  • 19 years ago

    Hello, I know this does'nt contribute too much to the discussion but one of my lawnboys has what I would consider a prototype carb float. It is a model# 6430 commercial or "suburban" push mower. It has the "F" engine and the classic plastic carb but the only difference is the float was made of black plastic and the arm was stainless steel instead of brass.
    I don't know if it was some sort of replacement but I always wondered why lawnboy or OMC did'nt use them in all the carbs. Probably was not cost effective or something.

    Neal

0
Sponsored
Bella Casa LLC
Average rating: 5 out of 5 stars17 Reviews
The Leading Interior Design Studio in Franklin County