Software
Houzz Logo Print
occamsshaver

6.75 Tecumseh engine no longer starting

20 years ago

I'm hoping that someone here might have some words of wisdom for me. I've got a 22" Craftsman mower with a 6.75 Tecumseh engine. I recently picked it up used and wound up spending a hefty sum on a new bag and frame... and a few weeks later, my mower isn't running! It was starting flawlessly just a few weeks ago.

It is getting spark. If I press the prime button ~ 10 times or so, and pull the cord, the engine will start and run for about 3 seconds then die out. It won't idle any longer than that. The air filter looks brand new (I believe the guy I bought it from was big on maintaining his lawn machines).

Any ideas what the culprit might be? I'm mechanically-inclined, but don't really know the intricacies of a lawnmower engine.

Thanks!

Comments (14)

  • 20 years ago

    Old gas? Always use fresh gas with Stabil added.
    Bad gas cap? Loosen cap a couple of turns and try.
    Clogged screen in tank? Visually inspect.
    Cracked primer bulb?

  • 20 years ago

    Take off the bolt that attaches the bowl at the bottom of the carbutetor. Before you do this, clamp the gas line with a vice grip so gas doesn't pour out on your garage floor. The bolt has holes in it that allow gas to pass through. These are probably the culprit, as they tend to get gunked up. Use a fine piece of wire to clean out the holes (twistie from a loaf of bread works good). I had the same problem with my Craftsman, and after cleaning the holes in the bolt, it runs like a champ.

  • 20 years ago

    pickngrin,

    Does this engine have a standard float bowl carburetor,
    or...is the bowl made of black plastic? We need to know
    this so we can tell HOW TO handle this issue. What you
    describe is a clogged/blocked main fuel jet. If a standard
    float bowl carb, the brass bowl nut that holds the bowl
    on "IS" the main fuel jet. Look on the upper side, just
    above the threads on this nut, and you'll see a very small
    hole/orifice. Poke out this hole with a piece of stiff
    wire, and clean rest of nut with carb spray. Replace nut
    and try running again. If the bowl is plastic....a complete
    bowl kit replacement is the WAY TO GO. Let us hear what
    you have, and we'll go from there....

    T-Man

  • 19 years ago

    Wow - I never realized there were responses to this thread. I'm sorry for not following up. At any rate, I am still having the same problem. I couldn't find a diagram for this engine online and was unable to figure out how to remove the carburator (I couldn't find any remaining screws or bolts holding it on, and it still wasn't coming free). I believe that I have the plastic bowl. There was no brass bolt at the bottom. Rather, there is a large-head screw which goes horizontally into the bowl and appears to control gas flow. The gasket that goes between this part and the engine is pretty beat up. I did get the mower running for approx. 8 minutes today, and was able to mow a small portion of my lawn... then it died again.
    In my quest to figure out how to remove the carb, I removed the bolts that fasten the head (where the spark plug goes). I then bolted the head back on. Shortly thereafter, I tried starting the engine and oil came out where the (paper) air filter goes.
    Does this sound salvageable? Does anyone know where I might find a diagram that would help me remove the carb?
    Thanks!

  • 19 years ago

    The bottom end (square plastic bowl) is removed by
    popping the clip off the bowl with a screwdriver. A
    new bowl kit (Tecumseh part# 730235B) replaces the
    entire bottom end. The crankcase breather is at the
    very top of the cylinder, under the flywheel. About
    the ONLY way oil can come out the air cleaner is if
    the engine was tipped on its side. There's a rubber
    tube that runs from the breather to the A/C housing.
    Oil can run down that breather tube and into the A/C
    housing if the mower is tipped on it's side. If you
    took the cylinder head off, you probably should REPLACE
    it...Tec part# 36061. I'd drain the crankcase oil and
    re-fill with 27 ozs. of 30HD oil. To install the bowl
    kit, clamp off fuel line, remove line from bowl nipple,
    install new kit, re-install fuel line, un-clamp line.
    This should restore the carb to "LIKE NEW". If your air
    filter got soaked with oil...replace that, too...Tec part
    # 36046.

    T-Man

  • 19 years ago

    'If you
    took the cylinder head off, you probably should REPLACE
    it...Tec part# 36061'

    Cylinder head or gasket?

    'I'd drain the crankcase oil and
    re-fill with 27 ozs. of 30HD oil.'

    This engine takes 27 ounces?

  • 19 years ago

    Saxman....I wasn't very clear in re-reading my post. I
    was suggesting replacing the head gasket and NOT the head.
    The Vector/Millenia style engine is "UNIQUE", in that, it
    DOES TAKE 27 ozs. of oil vs. the standard rotary mower
    engine (ANY brand) and 20 ozs. ANY rotary mower engine you
    come across with one of these plastic bowl carbs....is the
    Vector/Millenia engine design I'm referring to. ALL take
    27 ozs. to fill their deeper oil pan and crankcase. A nice
    selling feature of the engine.

    T-Man

  • 19 years ago

    I was given an old Poulan tractor. The carb. has the square black plastic bowl on it. I'd never seen one of those on a large tractor mower. I guess I'll have to get a new bowl assembly, since it only runs for 10 seconds with ether, or gas squirted into it. I did replace the fuel filter-it was clogged.
    What is it that goes bad in the plastic bowl? There aren't very many parts in there.
    I'm over-run with lawn tractors this week! Most of them weren't stored properly for winter, is the big problem.

  • 19 years ago

    T-Man,
    Thanks SO MUCH. I had been able to remove the bottom end but I couldn't figure out how to remove the whole carb. If the bowl is all I need to replace or clean, so much the better. Is there anything I need to know about replacing the head gasket or do I just place it on and bolt the head back on? I don't own a torque wrench (nor have I ever used one); do I need one?

    Are you a parts vendor? If so, I'd be happy to give you my business.

    Thanks again
    Pickngrin

  • 19 years ago

    Head bolts are tightened in a somewhat crisscross pattern. I'm thinking about 15 foot pounds. It's hard to describe the torque, but if you put your socket wrench on the bolt and left your arm drop on the end of the wrench, it might be 5 foot pounds. Go from there.

  • 19 years ago

    I got the mower running! I was able to buy both parts locally and followed your instructions.
    Thanks again!

  • 19 years ago

    Rusty,

    Bowl kits:

    Walk-Behinds 1997 and earlier - 730235B
    " " 1998 and to date - 730637A

    Riders 11-13HP - 730638
    Riders 15-18HP - 730639
    Rider w/Twin Cyl - 730649 (2 Kits Needed)

    ALL these kits RETAIL for $17.50 or thereabouts. They
    are the ONLY WAY TO GO when servicing this style carb.
    Quick, no guesswork, and a money maker for the repair
    shop.

    T-Man

  • 19 years ago

    Thanks, T-man, for the info, and numbers! I haven't got back to that machine, although i did spring for the float bowl kit! I'm trying to get a tractor running for a friend, and then there's a JC Penny riding lawn mower which has sat in an open shed for some time, and its owner wants it to run, and etc. Well, at least, it cranks! Needs lots of TLC!
    Rustyj

  • 16 years ago

    I know this thread is ancient but I hope someone can help me. Like those above, I also have a Craftsman mower with 6.75 hp engine, plastic float bowl. I installed the new bowl kit (Tecumseh part# 730235B), new plug, new air filter, changed oil, fresh gas, new fuel line, new "vacuum" line (behind the primer bulb). Still won't run. Not even for a second. It spins fine, has spark. Here's my main question...there was a small spring in the kit, no instructions. In my manual, the exploded diagram shows the spring goes at the bottom of the red "nozzle" that stands vertically and goes up into the carburetor body. The bowl I removed did not have this spring. Is it necessary to install this? I'll be pulling it apart again tomorrow and spraying some Gumout on the carb to see if that helps. Any other ideas? Thanks