Software
Houzz Logo Print
mbergen_gw

shop vac questions

19 years ago

Hi. After doing some research on this, and reading some of the posts here, I decided to buy a shop-vac at Lowes that will pump out the water to clean my pond - I think I saw the model discussed here.

I tried it last night, and it appears I will empty my entire pond trying to clean it out. It's not that big - maybe 6' x 10' and 3' deep with plant shelves. Right now the fish are in another pond that I built last week, but my hope was to be able to use it with fish in there in the future.

A couple of questions: Can I return the water I am pumping out, back to the pond, if I dedicate the shop-vac to only use in the pond? I know I read in the FAQ that you have to be careful doing this cause there's not much oxygen in that water - but thought maybe it'd be ok returning it to my waterfall that flows to the pond first so it was filtered by the plants in there.

Or: Is it better to return it and get the Muck-Vac that I had thought about getting instead. I got good water pressure with the inexpensive hose operated vacuum I have now - just didn't like the fact that it would fill the pond up with chlorinated water fairly quickly so I could never use it with fish in it.

I'm also wondering if it would be good to get a skimmer. It is near a pine tree so gets lots of needles in the pond, plus maple seedlings, etc. I may look into that but in the meantime I need to clean it. Maybe best for now just to drain it again and vacuum it out and start over with new water. I'm worried though about catching fish. I have some pretty small goldfish. I used to occassionally catch them in my pump, even though it was inside a filter - so i put a nylon around the pump to keep them out.

Meg

Comments (7)

  • 19 years ago

    Here is a DIY to go along with your shop vac. Other wise you got a lot of dumping to do..........

    Here is a link that might be useful: Floyds DIY

  • 19 years ago

    We've used a shop vac to clean ours for five years now with no problems to the fish. And yes, it does take out some of the water, but if you don't turn the vac on until the hose is on the bottom of the pond, you don't loose as much. Also a 10 to 15% weekly water change is good for the fish, just add declor when adding back the fresh water.

  • 19 years ago

    If you by a reducing attachment for your shop vac and cut the hose size down to 1 1/4" you will be able to get more vacuuming done before your tank fills up. You asked about returning the water back to the pond.

    Can I ask how you would filter the gunk you just vacuumed out of the water you're putting back in the pond? I'm not being a smart azz either, if you've thought about a way to do this I'd sure like to know.

    My last thought is that if you end up emptying your pond by vacuuming the sludge out, then I would re-evaluate your maintenance procedures throught the rest of the year.

  • 19 years ago

    Hi. Thanks for replying. I have a half barrel waterfall that flows into a mini stream I made with three separate pools in it, that then flows into the pond. That is filled with plants like parrotfeather and iris, so I thought I might be able to let the water out in there in the barrel, so that it goes through the plant roots and the three sections before getting into the pond. It's a bit easier to vacuum out those small areas than the big pond. Also I read some info here about putting a nylon stocking on the hose inlet so all the gunk doesn't get into the shop-vac in the first place so it's cleaner water - think I might try that.

    I could perhaps put rocks into one of the pools so the water goes through that as well before getting to the pond.

    I did let the pond go too long without cleaning it up - other than cleaning the filter regularly.
    I had a problem with one of the the floating plants getting out of control (frogbit I think)so I decided to empty it all out to try to get that plant out of there as well as give it a good cleaning, so I built a second fairly good sized pond to put the fish in in the meantime. That should help - just having a place to put the fish if necessary.

    Meg

  • 19 years ago

    Try adding some quilt batting to one of the barrels, it'll catch most of the gunk. Just take it out and rinse it ever few days.

  • 19 years ago

    Queensizeponder gave you the solution with the quilt batting in the barrel.
    I sit my shop vac over a half barrel and have fitted a 1¼" valve on the vac's drain. When the vac fills, I open the drain and let the water out to filter through the quilt batting in the half barrel. Then it goes out a spout and back into the pond.
    I also have a leg of a panty hose trapped into the in-put port of the vac to catch the heavier sludge /leaves etc as the water passes into the vac's tank.

    The quilt batting catches 99% of the junk.
    The plant roots would not be that effective in filtering out the fine particles.

    This I find is better than using the pump in the vac,[ if you have that type] as it cannot keep up with the suction and becomes plugged up to easily. Those pumps are meant for clean water really, not for pond maintenance.
    "Horton"

  • 19 years ago

    Thanks for all your replies. That quilt batting sounds like a good idea. I decided to return the shopvac, and have ordered the pondvac 3 (seemed more suited to pond use than what I got) on ebay. I don't yet know how it works to return water to the pond, but I think it will be better than what I got.

    Thanks.