Software
Houzz Logo Print
buster1_2021

22 hp briggs won't start

16 years ago

model 40h777 code 050120y0 type 0241 E1 22 hp Briggs

Problem The motor won't start without a quick shot of starter fluid. Once running it runs long and strong. After a cool down same thing it needs a shot of starter fluid.

I have put in fresh fuel.

Checked spark and plugs.

I pulled the carb off and sprayed cleaner (I did not rebuild)

Is there a way to check fuel pump or backfire solenoid?

Does anybody have any suggestions?

Comments (12)

  • 16 years ago

    chk throttle linkage at carb to verify choke is engaged when throttle/choke control at dash is activated.

  • 16 years ago

    I agree with rcbe, sounds like it is choke related. Forget any suspicions you might have about fuel pump or afterfire solenoid, neither of those components would yield the symptoms you describe. If it was either of those, you would not be able to achieve start-up at all (except for a second or 2 until the starting fluid was consumed).

  • 16 years ago

    I just checked the choke and it seems to be working fine. I just ran it for about 10 min to warm it up, turned it off and it wouldn't start. So it won't even start when it's warm.

  • 16 years ago

    how did you check plug/spark when it won't start ?

  • 16 years ago

    I grounded each plug to the block and cranked the motor.

  • 16 years ago

    you should have seen a bright blue spark... and that has to be done right at the time the engine wont' start... such will detect probs in the ignition circuit, such as weak coil when engine is hot. A yellowish spark indicates problems.

    Also make sure engine cooling fins are clean - rodents. etc. love to winter over in such spots. Remove engine xhroud sheet metal to ck - also closely check ignition leads for any mouse chewing damage... they like insulation.

    Also remove carb air cleaner and observe correct choke plate movement when /choke throttle control is activated.

    Does they starter crank the engine briskly while it won't start ?

  • 16 years ago

    It's funny how things change. My neighbor said the motor was only firing on one cylinder. To make a long story short, the starting problem was a bad plug on one side and a bent push rod on the other. The valve is moving freely so I got a new push rod and will put it in later on tonight. What will go wrong next?

  • 16 years ago

    That push rod bent for a reason. Generally the valve is sticking OR the valve guide has worked up to where it hits the valve spring retainer. Valve guide working up usually is caused by a cooling problem, cooling shroud, cooling fins plugged.

    IF this would be the problem, B&S says the head has to be replaced. I do have a fix for it. I also have instructions for adjusting the valves.

    Walt Conner

  • 16 years ago

    I would be interested in knowing your fix for the bent push rod problem. Jim

  • 16 years ago

    The fix is for loose Valve guide which MAY be the cause of bent push rod. Too long for here. Address below, put in proper format.

    Walt Conner
    wconner5 at verizon dot net

  • 16 years ago

    Walt could to much lash or the valve adjuster working loose cause the valve stem to eventually get bent? It may of just worked so loose over time that it started hitting the piston?? just an thought?

  • 16 years ago

    "Walt could to much lash or the valve adjuster working loose cause the valve stem to eventually get bent? It may of just worked so loose over time that it started hitting the piston?? just an thought?"

    I don't follow that. IF the adjustment got very loose, the valve would travel LESS distance into the cylinder and be less likely to be hit by the piston.

    It was the push rod that was bent anyway??

    Walt Conner

Sponsored
Landscape Management Group
Average rating: 4.9 out of 5 stars33 Reviews
High Quality Landscaping Services in Columbus