Software
Houzz Logo Print
hchdg

Briggs 18HP Wont Start

16 years ago

Preface: Not an expert at small engines by any means. I have used other posts on this forum to get me this far! I apologize for the length of this post, but this is everything I have tried to date:

I have an 18 HP 422707-1510 briggs and stratton that ran fine last year, then stalled one day and has not started since.

I have a new coil, new starter, flywheel was pulled-key looks good and the carb. is getting fuel. I have used the 'screwdriver' method to check spark and it looked REALLY weak with new plugs and new coil, so I am getting a spark tester today and see how that goes. When I pour fuel into the float bowl of the carb it does spit it out at a fairly high rate. But I figure that even if it was really rich it would at least fire for a short while???

The valves are not adjustable (1510) but they are not open at the same time so I figure that is a good sign...

Can any of the switches (deck and gear selection) allow the motor to crank and prevent spark??? I thought the safety switches prevented cranking as well??

ANY help would be GREATLY appreciated!!!!!!!!!!!!

Matt

Comments (27)

  • 16 years ago

    EDIT:
    I do start it with jumper cables and a car battery as the battery is completely dead, but I did that all last year and it seemed to run fine????

  • 16 years ago

    "The valves are not adjustable"

    Well of course they are BUT I doubt very much if that is your problem. What does (1510)mean?

    There are several things you can do to test. As far as safety features are concerned, somewhere on the engine there is likely to be a terminal where the "kill" wire junctions with other wiring harness. Check for this above the left hand Intake Manifold just below the edge of the cooling shroud. Left hand while facing the Intake Manifold side of the engine. Disconnecting the wires here will disable all safety switches as well as the way to shut the engine off. You will need to shut off the gas, pull plug wires, short the terminal, in case the engine does start.

    That is just a start.

    Walt Conner

  • 16 years ago

    the 1510 is the model of engine, and everything I have read they are not adjustable, unless you are grinding on the cam to shorten their length.
    Will the coil still function properly with the black wire not connected? I have tried with it on and off, no difference.

  • 16 years ago

    Firing means the engine ignition system is producing a spark.
    Cranking means the engine is being spun by an external force, usually a starter but if you are pulling on a starter rope, you are still only cranking the engine.
    Running means the engine is operating on its own power.
    These terms are not interchangable, each one means a specific, and different, process.
    Seat switch will prevent the ignition system from firing but will not affect cranking.
    Clutch switch and PTO switch will prevent the starter from cranking the engine, but have no effect on ignition firing.
    Your model # is 422707, 1510 is the first 4 digits of the type # (see first photo).
    So, the engine does not try to run at all when you pour some fuel into the open throat of the carburetor, is this correct?
    Have you tried separating the kill wire at the electrical post as suggested by Walt? (second photo)

    I also included a clickable link to the Briggs IPL for your engine. You can download that IPL for free and keep it in your computer, handy for reference.

    {{gwi:325617}}

    {{gwi:325618}}

    Here is a link that might be useful: 422707

  • 16 years ago

    You are correct mo, fuel in throat of carb and it will not fire, just crank. Great info on the other switches which means I can rule them out as bad if the engine is cranking. The pic of the kill switch post is awesome THANKS! I will disconnect that tonight and see what happens. Dont want to get ahead of myself but if it runs with the kill switch removed, is that indicative of an electrical short?

    Walt, Mownie, thank you again for the help.

  • 16 years ago

    If you disconnect the wires from the post (don't let the loose end touch metal) and the engine runs, that could indicate a short in the wire (left wire in picture) that leads to the seat switch and/or ignition switch, but it could indicate a defective seat switch . If you disconnect the left wire and the engine still will not run, access the ignition coil and remove the small black wire (this is the other end of the wire on the right side of post in picture). If the engine runs now, this would indicate that this wire is shorted (mice chewed insulation or vibration chafed insulation). If the engine runs after pulling off this wire, reconnect the wire to see if the engine dies. If it dies, replace this wire with a new one (you can make the wire). Do not run the engine with the flywheel cover removed for more than a few seconds (engine will overheat).
    If.....the engine still does not run with the kill wire removed completely, check for spark as you have been doing. If you do not get spark, you may have a defective ignition key switch, and the defective switch has fried your new ignition coil. If you have no spark, test the wire on the left side of post with a test light or a voltmeter to see if this wire has any voltage present. Test it in all positions of the key switch, including OFF and START. Read this very carefully: THIS WIRE SHOULD NOT HAVE VOLTAGE ON IT AT ANY TIME.....If you detect 12 volts on this wire, your key switch is either defective, or else it has been mis-wired (easy enough to do if it uses individual wires instead of a molded connector plug).
    Do these tests and post back.

  • 16 years ago

    Mo, not sure how to post pictures yet so I will describe:
    The kill switch is not wired to the block as in your picture, it connects to the wiring harness that goes to the clutch pedal switch and merges with the ignition wiring harness. The seat switch wire has been removed, tested with in on just to make sure and no change. The motor will NOT run with the kill switch completely removed from the coil. I manual compressed the clutch switch and that produced no change either. But with a spark tester on the ONLY spark occurred after the motor was cranking and when I let go of the key, meaning as soon as I let the key out of the start position, I get ONE spark before the engine stopped cranking. Sound like an ignition key switch?????? This was repeated several times, just the one spark??
    I will try to get pictures up later today.

    Thanks again!

    Matt

  • 16 years ago

    The ignition coil on this Briggs engine is completely self powered and uses no external source of voltage to power it. In fact, applying any voltage to the coil through the "kill wire" will do just that to the coil.
    You can tell us what brand of tractor the engine is in (along with the full technical model number) cause we may need that info shortly.
    I hope you did the test to see if you were getting any voltage on the kill wire like I described. Since it appears your application lacks the standard Briggs post on the front of the engine, you need to do the test for voltage as I described to the disconnected kill wire at the coil. Report back on that and then we will choose from there where we need to go next.

    Here is a link that might be useful: post pictures primer

  • 16 years ago

    {{gwi:325619}}
    This is a picture of the kill switch going to the coil. The arrow is just pointing to the connection on the coil. When following the wire that is spliced into a yellow wire, you can see that it goes into the wiring harness and ultimately ends up at the clutch switch. There is NO voltage reading from the kill switch when cranking or not.
    Engine is 422707 1510 01.

  • 16 years ago

    When I said we need the full Model number of the tractor, I meant for the vehicle chassis, not the engine. But what you say about the single spark at the end of cranking might mean something, might not.
    The fact that you are not getting a series of sparks when the kill wire is completly removed from the coil is puzzling. Do you have BOTH spark plug wires removed when you check for a spark? Do you have BOTH spark plugs out of the engine (so it can crank fast) when you check for spark? On this engine, both plugs fire at the exact same time. One cyl is on compression, the other is on exhaust. This is called "wasted spark". Leaving one plug wire connected while trying to check for spark on the other can give dubious results.

  • 16 years ago

    I am not an expert on this - but I think you have the coil installed upside down.

  • 16 years ago

    Sme say one plug wire has to be grounded inorder to get the other to fire(?) B&S says to not operate this (series) of engine with one plug wire disconnected.

    OK, the coil in the picture above is on upside down. The spark plug wires on these engines exit the coil heading towards the "back" of the engine, do a `180 degree loop under the coil and come out on the spark plug side of engine. Kill wire is on opposite side, down.
    Walt Conner

  • 16 years ago

    Mo, mower is a craftsman signature 1000 mower, circa 1992 or so. I will have to look tonight for any other identification numbers on the mower. When using the spark tester, I have both plugs installed with one plug wire attached to the plug, one to the tester.
    I have been testing spark with one plug wire connected and I have tested both plugs with the exact same result.

    Walt, the coil being upside down would not affect the spark right?? Does the direction the magnet passes by the coil change the rate of spark?

    Could the ignition switch be failing - allowing the engine to crank but not allowing spark??? that doesnt make a lot of sense to me though.

  • 16 years ago

    Coil upside down certainly will affect spark.....and spark timing. Upside down coil is sort of like "putting the cart before the horse" in the ignition sequence of events.

  • 16 years ago

    I will flip it tonight and see what happens. Thanks for the quick response, can't wait to get it running. Feel like a pretty big bonehead installing something upside down.......!!!

  • 16 years ago

    TWO VERY common errors people make with this general B&S series of engines is install coil upside down AND connect fuel pump backwards.

    Walt Conner

  • 16 years ago

    It fired up and ran! but... It definitely fired right up with the coil in the proper alignment. Now the fuel pump doesn't seem to be sucking any fuel, but there is no clamp on the suction hose so I will clamp it and see if that fixes the problem.
    Secondly, after it died from lack of fuel, I cranked it again and the starter would spin the flywheel, then suck back into the starter housing without me letting up on the key. It did that a few times, then a click, then nothing at all. It was hooked up to my truck via jumper cables so I know it was getting power. Ignition switch or starter Solenoid went bad??? How do you test those switches? I do have a multi meter but I do not really know how to test this type of stuff with it??

  • 16 years ago

    "Now the fuel pump doesn't seem to be sucking any fuel"

    Did you read my post above? Vacuum line to fuel pump connects to bottom, fuel line to side.

    I'll let Mownie explain how to check solenoid and switches out, it will take a long post and I don't have the fortitude for that.

    Walt Conner

  • 16 years ago

    For this, a 12 volt test light will probably be easier to use than a volt meter. So that's how I will describe the tests. The battery must be fully charged for these tests to be accurate and you must make sure there are no blown fuses. Clip the ground of the test light lead to a known good ground, negative post of battery is ok. Confirm the test light works by touching the probe of the light to the battery positive post. If light works, proceed to tests. You might want/need a helper to turn the key switch if you have short arms.
    Lock the brake pedal and make sure the PTO switch or, or other engaging method is not engaged.
    Touch the probe of the test light to the small white wire on the starter solenoid, turn the key switch to the START position. If the test light burns, the entire control circuit for the starter solenoid is good. If this is the case, move the test light probe over to the large post on the solenoid that has the cable going to the starter. Turn the key switch to START position. If the test light burns now, the starter is faulty. If the test light does not burn now, the solenoid is faulty.
    Now, if the first test of the white wire did not cause the test light to burn, find the brake switch and locate the 2 white wires on that switch (there might be 4 wires on the switch, only check the white wires). Turn the key switch to START and hold it in that position. Touch the probe to each white wire. If the test light burns when touched to both wires (one wire at a time of course), the clutch/brake switch is good. This would mean there is a break in the white wire between the brake switch and the starter solenoid (because you have power on the white wire leaving the brake switch but no power on the same white wire arriving at the solenoid).
    If you have power showing on just one white wire at the brake switch (with pedal locked down) replace the brake switch.
    Now, if you don't have power at either of the white wires on the brake switch, move up to the PTO switch.
    Find the white wires on the PTO switch and place the probe on the white wires one at a time. Turn the key to START. The test light should burn on both white wires. If only one white wire has no power on it when in START position, replace the PTO switch. If you have power on both wires here, but not at the brake switch, there is a break in the wire between the PTO switch and the brake switch.
    If neither white wire at PTO switch has power, move to the ignition key switch itself.
    Find the white wire on the back of the key switch and place the probe on it. Turn key to START. If you have power on the white wire here, but not at the PTO switch, there is a break in the wire between the key switch and the PTO switch. If you do not have power on the white wire here, the key switch is defective.

  • 16 years ago

    Mo,
    Thank you for your patience and diligence in that last post. I will tackle that this weekend, finally have some time.

  • 16 years ago

    What patience & diligence are you talking about??
    That is a "Copy & Paste" rendition from my "stock files" :^)
    We'll be right here.

  • 16 years ago

    Did not hear if the fuel pump was connected correctly.

    Walt Conner

  • 16 years ago

    Sorry for the delay, work and life has been busy!!!!!!!!!
    So I have not tested the starter switch yet. But, I think it has to be cooked: When the Key is in the 'off' position and I hook a jump box to the battery, the starter spins, but does not come up. When I turn the key to the accessory or start position, nothing happens? I am going to order a new starter switch, can't be that much $ right?? And eliminate a possible cause.

    Walt - The fuel pump is hooked up correctly, I removed some blockages so when its cranking again, I'll see if that was the problem.

    Is there anything in this process that could fry my new, $60 starter?? I really don't want to do that.........If so, how can I protect the starter?
    On that note, constantly jumping the tractor shouldn't really damage any components right?? I know the amps are different, but its not constant so no prob or risky?

    Thanks guys.

  • 16 years ago

    The starter only spins backwards when the key is in the switch in the OFF position. When turned to the ON, NOT start, position, NOTHING happens???????
    I replaced the starter solenoid and ignition switch, made no difference, same exact problem.

    ANY IDEAS???? I am 100% confused.

  • 16 years ago

    Are you saying that the starter spins backward when the key is in the OFF position? Does this mean that you are connecting the battery cables to the battery and when you touch the cable to the battery, the starter begins spinning, but backward??????
    The starter is a "DC Motor". For the starter to spin backward means that the battery is connected backward (reverse polarity). The correct configuration of cables at the battery are: Red cable to POSITIVE POST (+ sign), Black cable to NEGATIVE POST (- sign). The black ground cable connects to the negative post and the other end of this cable connects to the chassis frame, or the engine block.
    The red cable connects to the positive post and the other end of this cable connects to one of the large posts on the solenoid.
    Go out at double check how the battery is connected and then we will check some other things regarding how you might have mis-wired some things.
    One detail in your latest post that really bothers me is that you say the starter spins in the off position. I'm not really clear on whether this happens like I described above, or if you are "jumping" the solenoid manually, or just what the heck is going on!!!!

  • 16 years ago

    Mo,

    The negative lead off of the battery connects to one of the posts on the 3 pole solenoid. The other pole is positive, and the third is an orange wire that connects to the ignition switch.

    When the battery is hooked up correctly, the starter spins backwards when the key is in the OFF position. When the key is moved to the ON position, nothing happens, same with the START position, nothing happens. When the jumper cables are reversed, the starter spins in the opposite direction, but not with enough speed for the starter gear to engage the flywheel. The same switch problem persists in this situation, only spinning when key is in the OFF position.

    I have switched positive and negative connections at the solenoid, no difference in the direction of the starter. I have removed the third wire from the solenoid (not the positive or negative from the battery, the orange wire going to the ignition switch) and the starter still spins backwards when key is in the off position, nothing at On or Start.

    With the battery connected to the solenoid, both positive and negative, I have run a jumper from the neg. battery terminal to the engine block and frame to ensure proper grounding, and it made no difference, starter still spinning backwards...........................

  • 16 years ago

    COWLY HOW MATBAN!!!!
    Boy is that NOT wired correctly! (IF.....your description is accurate)
    On the starter solenoid, the wires/cables should be configured as follows:
    (1) The battery positive cable connects to one of the large posts of the solenoid.
    (2) The large cable that connects to the single post on the starter itself connects to the 2nd large post on the solenoid.
    (3) The small wire (should be a white wire, if OEM) connects to the small post or terminal. This wire is supposed to be arriving at the solenoid after having traveled through the clutch/brake switch and the PTO interlock switch.

    So, if you are telling us that both of the battery cables are connected to the solenoid..........well, that just can't work, and I think you must be mistaking (somehow) the cable that runs from the solenoid to the starter as being "a negative cable", which it is not.
    Double check all the wires/cables on that solenoid as to where they actually go to, or come from, and post back.

    If you could find the full, technical model number of the tractor we could probably view an online wiring diagram.
    Knowing the approximate year model is not much help because Sears does not list the manuals except by the full technical model number of the tractor.

    Post a picture of the solenoid as it is wired now please.
    I will try to find a Craftsman wiring diagram that "will fit" your tractor and post it to the forum.
    Refer to the photo I posted showing the Briggs numbers as they appear on the engine. Find the Code number and post it. That will narrow the date of the engine build and the date of tractor build will not be much later than that.
    I will then try to correlate a "printing date" from a Craftsman manual that is close to the engine Code number date.
    One more question.......does this tractor have an electric PTO clutch or does the deck engage manually by moving a lever??
    OK, that's your homework for today and I gotta head off to my job now.

Sponsored
Urban Upkeep LLC
Average rating: 5 out of 5 stars6 Reviews
Columbus High Quality Painting Expert