Software
Houzz Logo Print
o2mow

17 HP Briggs Will Not Start Warm

17 years ago

I have a Briggs & Stratton 17 HP lawn tractor (42a707 engine model) that has me completely stumped. It starts fine when cold but will not start when the engine has been running a while. I have replaced the spark plugs, rebuilt the carb and replaced the coil. I have even tried removing the coil grounding strap without success.

Today, I ran the lawn tractor for about 1/2 an hour. I stopped it and then immediately restarted it. To my surprise it started up. I waited 10 minutes and then it wouldn restart. I checked and it had spark (using a spark tester). I definitely smelled gasoline, so I believe it is getting feul. I gave up trying to start it after about 5 minutes of cranking (when the battery died). While cranking, it didn't even sputter.

Any help or suggestions are appreciated.

Comments (9)

  • 17 years ago

    Does the engine have a fuel pump or is it gravity fed? If it is gravity fed, does it have an inline fuel shutoff valve? If it is gravity fed and has an inline fuel shutoff valve, next time you plan to "stop the engine", turn off the inline fuel shutoff valve and let the carb run "out of fuel" before stopping the engine. It sounds like the carb float needle valve might not be stopping the flow of gas and this might be "flooding the engine". After doing this test, do not turn on the fuel valve until you are ready to restart the engine. If the "hard starting hot" disappears, the carb has a problem with the float needle & seat. If it is gravity fed and you DO NOT have an inline fuel shutoff valve, how come you don't add one....and then do the test?

  • 17 years ago

    Agree completely.

    Walt Conner

  • 17 years ago

    Thanks mownie, Walt for the suggestion. I have an 18HP Briggs twin with same symptoms. Well, I used to have those symptoms before I decided to never shut it off once it's started for the day. I ran it nonstop 3+ hours last week, hauling stuff to my brush pile. Spent 95% of the time idling while loading/unloading the trailer. Very wasteful. Gotta fix it.

    But wouldn't a nonfunctioning float valve cause the flooding to happen at all times, including parked in the shed for days or weeks between uses? I'm not understanding the 'warm engine' aspect of it.

  • 17 years ago

    ****"I have an 18HP Briggs twin with same symptoms."***
    How much "the same" is YOUR 18HP Briggs twin, to the example machine in the OP (who, by the way, has not bothered to reply yet)??
    But to answer the portion of the question that COULD apply to ***"wouldn't a nonfunctioning float valve cause the flooding to happen at all times, including parked in the shed for days or weeks between uses?"***
    Yes, it would "attempt to flood" at all times, BUT, if your engine is fed by a fuel pump (instead of gravity) the faulty float valve can still leak enough fuel to flood the engine and cause "hard starting hot", simply by the amount of fuel in the fuel hose between the output connector of the fuel pump and the carb float valve. If the engine were stone cold....that same amount of fuel leakage would not hamper the engine from starting up (could help actually as it would be a "rich mix", which a cold engine wants for starting). The fact that YOUR engine is hard to start after a hot shutdown could be due to flooding temporarily because of the scenario I described, but not filling the engine crankcase with raw gas during storage because your engine might be "pump fed". You did not state whether pump or gravity, so I can't say how exact your situation is to the OP's situation, and since that person has not yet divulged the same info.....it's anybody's guess whether the engine configurations are the same. Could be, but so far....no proof! The small amount of fuel leaking into the engine intake after shutting down a pump fed carb could certainly cause "hard start hot from flooding". BUT, that small amount of gas would evaporate and be gone long before it could make its way into the crankcase (the engine would still be somewhat warm when all the fuel finished leaking out of the carb and estabilshed a "stable level" in the bowl. Another thing I will toss in here, and forgive me if I seem to be making "an assumption". You are not by chance "using the choke" when you attempt to restart the engine hot, are you. Before you get all defensive, I have had a couple of cases where an owner/operator complained of "hard start hot" only to learn (by chance) that they were ALWAYS "pulling the choke" to start!!!!! HOT or COLD. Remember, hot engines flood at the slightest provocation, but cold engines "like" a shot of gas.

  • 17 years ago

    Model is 422707 1208 01
    I thought it was gravity fed but now I'm not so sure. There is a direct (via inline fuel filter) hose from tank to carb. More specifically, the hose goes to a rectangular-shaped bump-out on the front face of carb. There is another hose (same size) attached to that same bump-out that runs down to the engine block somewhere. I'll have to do some more research and reply later. I read something somewhere about a vacuum-type fuel pump, maybe that's what mine is and the rectangular bump-out is the pump? I'll check the Briggs website to possibly find an exploded diagram which offers some sort of explanation about what everything is and how it works.

    I don't use choke when attempting warm start. I will try 1/2 choke, then full choke, but only after 3-4 failed attempts at unchoked starting. Some combination of choke setting and throttle setting would sometimes finally work, but even that varied depending on whether the engine was shut off 5min ago vs. 30min vs. 1hr. It is terribly unpredictable. That is why I now just let it run.

  • 17 years ago

    "There is another hose (same size) attached to that same bump-out that runs down to the engine block somewhere."

    That is the fuel pump.

    Walt Conner

  • 17 years ago

    Thanks Walt.
    Now I know my engine has a fuel pump.

  • 17 years ago

    sorry for the delay in returning to this post...I thought I would recv an email notification when an updated occurred.

    The model that I have uses a feul pump on the carb. It is a 3 screw model. I rebuilt the carb as it had been sitting for a while. It uses vacum to power a little baffle that pumps feul into the carb. The little jet at the top of the feul tank appears to be open and clean.

    I don't use the choke to start a warm engine but have to admit after cranking for a few minutes, I have tried pulling it up to see if it made a difference.

    I replaced the feul filter before rebuilding the carb so I know it is good. I even cleaned the plastic tank at the same time to make sure nothing would block it.

    I don't have a feul shut-off but it sounds like that would be a good test and fairly inexpensive.

    I used to have problems with this engine back-firing when shutting it down hot...even after taking the throttle down to an idle.

    Thank you all for the posts and suggestions!!...sorry for the dely in responding....I thought this topic fell into the obscurity of the Internet

  • 15 years ago

    I have simuler problem and I have two briggs 17 and 17.5 hp. I tried all the things mentioned and I'm convinced it's a valve problem. I thought I had mine fixed but now I can mow my whole yard ad if I cut it off it won't crank because motor drags. I'm going to tighten valves again because too much pressure causes the compression to be too much and won't release. I know this because you can loosen spark plug and engine will turn over fine.

Sponsored
Urban Upkeep LLC
Average rating: 5 out of 5 stars6 Reviews
Columbus High Quality Painting Expert