Software
Houzz Logo Print
buellboy_gw

Deere 425 AWS starting and cooling problems

16 years ago

( Sorry if this post is a DUPLICATE- I tried to post this before and never saw it! Oddly if I search the postings by my username it comes back blank, and there is no button that says SEE MY POSTS. )

*************************

My 425 starting acting up at about 1100 hours. I just did the FULL service on it- fluids and filters. I didn't change the plugs yet- I'm not sure what it needs. It ran fine after the service for about 40 hours.

The first problem may NOT be a problem, but it seems odd. I can't keep the radiator or overflow tank full, or in the range I'd expect them to be.

They dont leak- I can fill them and check the next day and they are still full. But after mowing the overflow is empty and the radiator is down like 2 in. The tempo gauge stays well in the green - it seems to run cool. But it seems odd that I cant keep the levels up. After running there is a cup or so of coolant by the left front tire.

and the other problem...

Anyhow it starting quitting very suddenly, hot or cold, then its very hard to start. Today I started it cold, and tried to back it into the garage. It started INSTANTLY. I left the choke on like 1/2 as it likes that for the first 5 min or so.

Anyhow I started backing and died without sputter, after running like 20 seconds. I cranked and cranked- it would not start at all. I could not smell gas.

I noticed that when it gets in *this mode* the best thing to do is to turn the key like 2 seconds and release. It won't start if the key is turned, but *eventually* it will *catch* when its spinning, and they key is released, and sputter back to life (with 10 seconds of smoke) if they key is released.

Where is this timing relay located? ON that circuit board?

Comments (5)

  • 16 years ago

    You had better park it right now. Further use will just push it closer to oblivion.
    You stated some very significant symptoms that pretty well confirm you have AT LEAST........a head gasket leaking, but your water pump is also likely defective. And I don't mean "one or the other", I mean you probably have BOTH defects present.
    The cup or so of coolant by the left front tire is either leaking from the radiator recovery jug (overflow tank), or from the water pump weep hole, or both places.
    Your statement regarding the radiator & recovery jug, "They dont leak- I can fill them and check the next day and they are still full." is "partly true".
    They might not leak in the sense of having a hole or crack, but they are certainly "bleeding & venting pressure" during engine operation.
    What is happening is the head gasket is leaking combustion gases (under high pressure) into the cooling system and raising the pressure above the vent relief value of the radiator cap (usually 13 PSI). As the gases (and pressure) enter the cooling system, the radiator cap begins venting the excess pressure (along with coolant and combustion gases) into the coolant recovery jug. As the venting continues the recovery jug overfills, it begins to dump coolant out of its overflow tube. The loss of coolant from the radiator will decrease somewhat as the coolant level drops to a lower point, but the gases continue to be vented into the recovery jug and create a frothy mix of gases which continue to carry coolant out of the recovery jug (because the jug is "not pressurized"). The 13 PSI in the radiator keeps the foaming/frothing from happening there, but the recoery jug has not pressure cap.
    Since your engine has over 1,100 hours on it, and your have now experienced this very serious failure, it would be prudent to tear the engine down to inspect the crankshaft, camshaft, and related bearings.
    Inspect the cylinder walls for scoring (pre-galling streaks).
    You will also need to replace the water pump (it is probably worn anyhow) if the engine is still salvable.
    Radiator should ideally be flushed out (internal flush as well as complete cleaning of the core fins exterior).
    New radiator cap and a new thermostat will be needed too, if the engine is salvable.
    Click the link to read another recent case very similar to yours.
    Here's what happens after you cut off the engine. First, the pressure in the cooling system immediately drops to 13 PSI (because that is the value of the relief valve setting).
    With 13 PSI pressure in the cooling system, a small amount of coolant will be forced past the defective spot in the leaking head gasket and into the cylinder. This is why you are experiencing "hard to crank", the cylinder is "hydro-locking".

    Here is a link that might be useful: 425 Kaw engine total loss?

  • 16 years ago

    Ignition Delay Module is probably causing the hard starting. It's a little box near the ignition module.

    Mownie's post is dead-on about the coolant. Pressure check it. Poor man's check - get the engine hot and hold a coffee filter over the exhaust. If it gets sticky, there is coolant coming out. You can also run your finger in the exhaust pipe (when COOL!!!) to see if it's sticky/gooy.

  • 16 years ago

    Well, I guess I sort of overlooked some of the detail about the "starting problem" and inferred that it was not "cranking" properly.
    But at this point, I maintain that the problem with how it starts is "the least" of your worries (contrary to what you may think).
    Unless you address the coolant issue, you will soon not have to worry about starting this machine.

  • 16 years ago

    Water pump has a small weep hole that will let the coolant out. It can be hard to see, you may need a flashlight.

    You may notice haze or steam like smoke puffing from the exhaust if you have coolant in the oil or blown headgasket. If you have a lot of coolant in the oil the water vapor etc can wet foul the plugs, had this on a Kubota this past week.

    I would check the oil for a milky look. The water pump seals can fail and allow the coolant to enter the crankcase, since the pump is driven off the camshaft gear.

    I have seen the Kawi engine's loose the pump seals and most of the water went into the engine, if so flush the engine after you replace the pump and 2 gaskets.

    Torq the pump bolts to 70 lb in's and the 1 large bolt to 187 lb in's.

    Good Luck

  • 16 years ago

    Forgot to mention the TDM, Time Delay Module.

    Engine Tech is right, the black box is on the left hand rear side of the engine. I bypass those things most of the time unless the customer wants to keep it. Most say bypass it.

    All you have to do is check for spark at both plugs. No spark at either plug could be a bad TDM. Spark at only one plug might just be a coil issue.

Sponsored