Software
Houzz Logo Print
wayneinala

.030 or .040" gap on Kohler

14 years ago

This is an old question I've had. On my John Deere mower with a 17.5 hp Kohler CV491S single cylinder OHV engine, the JD manual calls for a plug gap of .030". The Kohler service manual calls for a .040" plug gap. I emailed Kohler and of course thaty said theirs was correct. Anyone else run into this?

For what it's worth, I've run both gaps and in-between and did not see any difference.

Comments (7)

  • 14 years ago
    last modified: 11 years ago

    I would trust Kohler.

    Often the tractor manuf. will copy & paste sections from one manual to a new manual and simply miss.

    There's a bunch of Craftsman manuals that specify the wrong fuel filter for some of their Kohler engined tractors.

  • 14 years ago
    last modified: 11 years ago

    Yes, and for what it's worth it probably will not make much difference in the future either.
    Some theory regarding this subject:
    Gaps closer than .030" make it TOO easy for a spark to "jump across" and therefore results in a smaller and cooler arc. And because there are fewer molecules of fuel occupying that narrower gap, the flame propagation front will be smaller resulting in a somewhat slower spread throughout the combustion chamber............which ultimately means there will be less power produced and more UNBURNED fuel going out the exhaust during the exhaust stroke.
    But.........because the gap is narrow, the moment of spark will be slightly earlier and of a longer duration than with a wider gap.
    So the bad effects of a narrow gap are somewhat mitigated, and the operation of the engine will be near normal.

    Gaps greater than .040" result in a much hotter (relatively speaking) spark and the wider gap allows more molecules of fuel to be involved with the spark resulting in a larger flame propagation front to spread quickly throughout the combustion chamber. Theoretically this would seem to ideal........but because the wider gap is harder to force a spark across, the actual moment of spark is a bit later and of a shorter duration and that means that any benefits of a hotter spark are offset by the time of the spark.............so the operation of the engine will be near normal.

    Any spark plugs and the ignition systems using them are designed to work inside of specific parameters, no matter what brand of plug or engine. The parameters are actually quite generous as to what will work.
    A gap range from .025" to .045" is actually within the theoretical parameters of the old school automotive and outdoor power engines technology.

    When you attempt to operate at gaps wider than say .050", you begin to see real problems with the operation of an engine that was designed around standard old school automotive principles and technology.
    Because of the extra energy required to produce a spark across the wider gap.........spark will not be a dependable event and misfire will occur.
    Also because electricity seeks the path of least resistance, the spark will tend to tunnel through the insulation of the plug cable in its pursuit of a path to ground. This will quickly become the route of choice for the spark under those conditions.
    The extra energy required will also cause more heating of the ignition coil which can lead to coil failure.

    Modern automotive ignition systems touting wide gap capabilities are designed from the start with that in mind and so are built to withstand the rigors of those conditions. Conditions which would surely kill a common outdoor power engine ignition system.

    Your experience with both .030" and .040" gaps bears out the fact that gap per se is not that critical in most applications.
    But gap is not the only factor affecting spark.
    Spark plugs do deteriorate with use and an old used plug is not as dependable a spark maker as a new plug.

  • 14 years ago
    last modified: 11 years ago

    Thank you for your replies.

  • 14 years ago
    last modified: 11 years ago

    Mownie, thanks for the detailed description. One of the reasons I hang out on these forums is that while you "know" something, you're not sure why or how it works. Folks like you provide detailed info for the rest of us.

    Thanks again,

    Ev

  • 14 years ago
    last modified: 11 years ago

    An excellent explanation by Mownie.

    Just to add a bit-
    Some of the "high performance" spark plugs simply use an internal air gap that's wider than the plug gap.
    Your coil is forced to build up more voltage to jump the internal gap and thus a "higher voltage" spark.
    The only advantage is the "air gap" isn't in the combustion chamber where compression makes it harder to jump the plug gap.
    The bad news is that it makes your coil "work harder" building up a higher than necessary voltage. This can cause dielectric break down internally and shorter coil life.

  • 9 years ago

    Ok I tried 40 and it ran soooo good it was the best it ever ran so definitely 40

0
Sponsored