Software
Houzz Logo Print
ez2fix

Craftsman Snowplow Attachment

18 years ago

I have a 1993 Craftsman Lawn Mower (Mod:917.255590) and I have found a snowplow that looks like it would fit. However,,, it looks like I need a bracket from the rear of the plow frame to the manual lift arm. The arm used for the mower deck does not look like it would work. Sears is absolutely no help. Does anyone know where I could find a manual for the plow attachment. I have the tractor manual but it does not cover the plow. OR,,, where there would be a large used parts place that might help. OR - OR,, would someone have a picture of the frame mounted plow attachment and maybe I could fabricate something myself.

Thanks.

Comments (9)

  • 18 years ago

    Do you know who made the plow?

  • 18 years ago

    Try:
    My neighbor made a cross tube that holds the back end of the main tube, from the front pivot, back to a point under the tractor. This is a cross tube that fits below the frame rails, with 2 plates bolted to the frame.
    I also conjured up a drawing of a newer model of snow plow, which i found in the Sears web-site.
    If the plow you have isn't made especially for a Sears tractor, you are on your own, and will have to rig it up some way for it to work.

    Type in your serial number, then poke around in there-i'm sure you will get some ideas on how to do it.
    www3sears.com. or: Searspartsdirect.com.

  • 18 years ago

    I just mounted Sears 46 inch snowblower to 5000GT Craftsman garden tractor. Here is a link to the snowblower manual.

    Here is a link that might be useful: Craftsman 46 inch snowblower

  • 18 years ago

    I realize that you are seeking info about a plow, but I thought method of mounting snowblower might be useful.

  • 18 years ago

    Sorry, I have been consumed by a charity "Duck Race". However, thank you to all that provided info. The plow that I was considering buying for $40-50 has been repainted a few times but the current owner says it is a Sears 42" plow off an old "grey" Sears Lawn tractor. I don't think he is going to sell it right away.
    The blade is 42" and it has the typical Sears manual angle and a long beam that has the hanging arm that would line up with the front end brackets on the tractor. The beam continues to the middle of the tractor and then has a pin that looks like it would line up with the raise/lower lever. Here is the issue: Looks like a need a 12-14" bracket to go between the back end of the plow and the raise/lower mechanism under the tractor.
    Other than that 1 bracket, I think it would fit. A manual or picture or even a drawing would help me find one or possibly fabricate one of my own.
    Thanks again for all that responded.

  • 17 years ago

    ez2fix.....
    I just went thru the same question process with my newly acquired snow plow.
    I have a Sears 12.5 hp 42" deck tractor, model 917.255581. I have a 'new to me', Sears 42 inch snow blade, model 486.244072. I have the same front end brackets as you do. If you enter the plow's number into the www.sears.com parts section and compare what your plow looks like, I think that you'll see that you're missing the lift mechanism, also shown on pg. 6 & 14, item #26. This mechanism attaches to the small pin on the end of the plow's main beam and attaches to the mower deck raise/lower mechanism.
    I would think that a replacement mechanism using a simple pivoting rod and handle, with locking mechanism, could be fabricated easy enough, not connected to the mower height handle, if the part is not available. The parts list says that it is available, p/n 62546. An adaption of the newer Craftsman plow lower/raise mechasism is another option.
    Just make sure that when the plow is in the down position, the main beam does not touch the lower pulley of the engine.
    Incidentally, my plow is NOT made 'exactly' for my tractor, specifically, but is close enough that a couple washers and longer bolts made it work.
    Incidentally, I just picked up a Sears single stage blower for the same old 'grey' tractor, but it's missing some parts, too. Another project in the works.
    All I need now, is SNOW!

  • 17 years ago

    I have just done the same and found a manual online.

    http://c.sears.com/assets/own/24441e.pdf
    Model # 486.24441
    42" Snow Blade

    I called Sears and they were still of little help in Canada
    You will find the parts you need.

  • 17 years ago

    After fabricating and mounting a homade snow-plow blade and lifting mechanism on a Model A Ford Homade tractor, some years ago, i find that making things just comes naturally to me, so:
    In the current photo in the Sears web-site, the snow plow lift arm/ bracket, is connected to the mower deck lift arm by a long steel shaft, via a clevis and pin/bolt. That shaft may have to be bent some to make it work correctly. The forward end is connected to a vertical plate that will tilt or raise the plow blade. And the regular slotted hold-up assembly will hold it up or down.
    From what i can see, the lower plow assembly doesn't lift up, but the blade tilts back and forward, depending on the setting of the side lift arm, the arm that normally lifts and lowers the mower deck. The blade assembly allows some angling of the blade, and that is controlled by another handle and rod on the left side. It didn't look very strong, especially if you were to run into a pile of hardened snow, from a previous snow removal job!
    My link to Craftsman snow plow: use model no. 486.244283.
    This is only for illustration on fabricating a snow plow lifting mechanism. HTH: Rustyj

  • 15 years ago

    I've been trying to find a diagram of the parts needed to attach a 42' craftsman snowplow to my 25 HP craftsman riding mower

Sponsored